When the windshield deicer switch is turned on, a windshield deicer activation request signal is sent via the LIN communication line*1 or CAN communication line*2 to the air conditioning amplifier assembly. Then the air conditioning amplifier assembly operates the windshield deicer. When the on signal from the windshield deicer switch is received, the DEICER relay is operated for 15 minutes. Also, if the off signal from the switch is received within 15 minutes, the DEICER relay operation is stopped.
*1: w/o Navigation System
*2: w/ Navigation System
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication and LIN communication malfunctions before troubleshooting this symptom.
Select the Active Test using the intelligent tester to generate a control command, and then check that the windshield deicer operates (See page Vehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Deicer Relay (Front) | DEICER relay operation | OFF or ON | - |
The windshield deicer system operates normally.
| Result | Proceed to |
|---|---|
| OK (w/o Navigation System) | A |
| OK (w/ Navigation System) | B |
| NG | C |
A
B
C
Temporarily replace the air conditioning control assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Navigation System)>REMOVAL).
Turn the ignition switch to ON.
Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.
Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.
Windshield deicer system functioning normally.
OK
NG
Check if the navigation system functioning normally (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Navigation system functioning normally.
OK
NG
Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Turn the ignition switch to ON.
Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.
Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.
Windshield deicer system functioning normally.
OK
NG
Temporarily replace the multi-media module receiver assembly with a new or normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (w/ Multi-display)>REMOVAL).
Turn the ignition switch to ON.
Check that pressing the windshield deicer switch illuminates the indicator and warms the front windshield surface.
Check that after approximately 15 minutes, the indicator light turns off and the windshield deicer deactivates.
Windshield deicer system functioning normally.
OK
NG
Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).
Inspect the DEICER relay (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).
OK
NG
Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).
Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.
*1: w/ Rear Heater
*2: w/o Rear Heater
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| DEICER relay terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay terminal 1 - E36-9 (FDEF) | Always | Below 1 Ω |
| DEICER relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEICER relay terminal 1 - E81-39 (FDEF) | Always | Below 1 Ω |
| DEICER relay terminal 1 - Body ground | Always | 10 kΩ or higher |
OK
NG
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Disconnect the A23*1 or A63*2 windshield glass (windshield deicer wire) connector.
Remove the DEICER relay from the engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Windshield Deicer)>ON-VEHICLE INSPECTION).
Remove the HWD1, HWD2, HWD3 and HWD4 relays from the No. 2 engine room relay block (See page Vehicle Exterior>WINDOW / GLASS>RELAY(for Window Defogger)>ON-VEHICLE INSPECTION).*2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-1 (B) - DEICER relay terminal 3 | Always | Below 1 Ω |
| A23-2 (E) - Body ground | Always | Below 1 Ω |
| DEICER relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-1 (B) - DEICER relay terminal 3 | Always | Below 1 Ω |
| A63-2 (E) - Body ground | Always | Below 1 Ω |
| DEICER relay terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the A23 windshield glass (windshield deicer wire) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A23-1 (B) - A23-2 (E) | Ignition switch ON and deicer switch on | 11 to 14 V |
| *a | Front view of wire harness connector:
(to Window Glass [Windshield Deicer Wire]) |
OK
NG