Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
67862
1.INSTALL FRONT DOOR WEATHERSTRIP LH
When installing the front door weatherstrip, heat the vehicle body and front door weatherstrip using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Front Door Weatherstrip | 20 to 30°C (68 to 86°F) |
Do not heat the vehicle body or front door weatherstrip excessively.
w/ Spot Cover:
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new front door weatherstrip LH.
Remove the peeling paper from the face of the front door weatherstrip LH.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Attach the 21 clips to install a new front door weatherstrip LH.
If clips are damaged during installation, replace them.
Press the front door weatherstrip LH firmly to install it.
w/o Spot Cover:
Attach the 21 clips to install the front door weatherstrip LH.
If clips are damaged during installation, replace them.
68620
2.INSTALL FRONT DOOR CHECK ASSEMBLY LH
Install the front door check assembly LH to the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the bolt.
68622C
3.INSTALL FRONT DOOR CHECK COVER LH (w/ Cover)
Install the front door check cover LH.
67924
4.INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION
When installing the front No. 2 door stiffener cushion, heat the vehicle body and front No. 2 door stiffener cushion using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Front No. 2 Door Stiffener Cushion | 20 to 30°C (68 to 86°F) |
Do not heat the vehicle body or front No. 2 door stiffener cushion excessively.
Clean the installation surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Install a new front No. 2 door stiffener cushion.
Using a heat light, heat the vehicle body and a new front No. 2 door stiffener cushion.
Remove the peeling paper from the face of the front No. 2 door stiffener cushion.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Attach the 2 clamps to install the door stiffener cushion.
Press the front No. 2 door stiffener cushion firmly to install it.
Install the 2 bolts.
89991
5.INSTALL DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)
Install the door electrical key oscillator with the screw.
69312
6.INSTALL FRONT DOOR LOCK OPEN ROD LH
Install the front door lock open rod LH as shown in the illustration.
89746D
7.INSTALL NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)
Connect the connector.
Attach the 3 clamps to install the No. 2 electrical key wire harness to the frame.
69202A
8.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Attach the 2 claws to install the front door outside handle frame sub-assembly LH.
Using a T30 "TORX" wrench, install the front door outside handle frame sub-assembly LH with the screw.
A cover should be inserted between the screw and door panel.
69760C
9.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Install the front door inside locking cable assembly LH.
Attach the 3 claws.
69720B
10.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Install the front door lock remote control cable assembly LH.
69320
11.INSTALL FRONT DOOR LOCK ASSEMBLY LH
69254C
12.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH
Attach the 2 claws to install the front door rear outside handle pad LH.
69252
13.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH
Attach the 3 claws to install the front door front outside handle pad LH.
69220
14.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
Pull and hold the bellcrank lever of the frame.
Install the front door outside handle assembly LH by pushing it in the direction of the arrow in the illustration.
Using a T30 ''TORX'' socket, install the screw.
w/ Entry and Start System:
Connect the connector.
69217F
15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH
Attach the 2 claws to install the front door outside handle cover LH to the front door lock cylinder.
Using a T30 ''TORX'' socket, install the front door outside cover LH (with the door lock cylinder) with the screw.
Install the hole plug.
85720C
16.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69802
17.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly LH.
Do not apply grease to the spring of the front door window regulator sub-assembly LH.
| *1 | Temporary Bolt |
Loosely install the temporary bolt onto the front door window regulator sub-assembly LH.
Insert the front door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the front door window regulator sub-assembly LH on the door panel.
Be careful not to drop the front door window regulator sub-assembly LH as it may become damaged.
Temporarily install the front door window regulator sub-assembly LH with the 5 bolts.
Tighten the 6 bolts in the order shown in the illustration.
75756C
18.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH
75720
19.INSTALL FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH
67674
20.INSTALL LOWER DOOR FRAME GARNISH LH
Attach the clip and install a new lower door frame garnish LH.
67404F
21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Install the front door rear lower frame sub-assembly LH with the bolt.
68151E
22.INSTALL FRONT DOOR GLASS RUN LH
Install the front door glass run LH.
68102
23.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.
Be careful not to damage the glass.
Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.
67832
24.INSTALL FRONT DOOR SERVICE HOLE COVER LH
Apply butyl tape to the door.
Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.
When installing the front door service hole cover LH, pull the links and connectors through the front door service hole cover LH.
There should be no wrinkles or folds after attaching the front door service hole cover LH.
After attaching the front door service hole cover LH, check the sealing quality.
Connect the 2 connectors.
Attach the 9 clamps.
Install the bolt as shown in the illustration.
89860A
25.INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH
86160
26.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
67856B
27.INSTALL FRONT DOOR PANEL PROTECTOR LH
Install the screw, and install the front No. 1 door stiffener cushion and front door panel protector LH.
89430
28.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
87940
29.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH
69278E
30.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
Install the front door inside handle bezel LH to the trim board with the 7 screws.
69206B
31.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Attach the 2 claws to install the front door inside handle sub-assembly LH.
84927
32.INSTALL SEAT MEMORY SWITCH (w/ Seat Position Memory System)
68172A
33.INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH
Install the front inner door glass weatherstrip LH.
67602
34.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Connect the connector.
Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.
Attach the 4 claws and 13 clips to install the front door trim board sub-assembly LH.
Install the 3 screws.
74646
35.INSTALL DOOR ASSIST GRIP COVER LH
Attach the 8 claws to install the door assist grip cover LH to the front door trim board sub-assembly LH.
84040
36.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
74232
37.INSTALL FRONT UPPER ARMREST BASE PANEL LH
69278B
38.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH
Attach the 4 claws to install the front door inside handle bezel LH.
81230
39.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
67492A
40.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Attach the clip and claw, and install the front door lower frame bracket garnish LH.
75072A
41.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)
42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
43.CHECK SRS WARNING LIGHT