Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) › from 2016.08
RM2660E _58 Vehicle Interior _052838 DOOR LOCK _0255552 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all the doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

w/o Tire Pressure Warning System


B242194E05
0.699,2.952 2.132,3.128 1.434,0.177 10 Door Control Receiver 0.699,2.767 1.019,2.943 0.320,0.177 10 L47 2.055,0.712 2.376,0.889 0.320,0.177 10 3 1.601,0.805 1.957,0.982 0.356,0.177 10 PRG 2.055,1.212 2.376,1.388 0.320,0.177 10 2 5.263,2.207 5.700,2.383 0.437,0.177 10 E118 1.605,1.305 1.945,1.481 0.341,0.177 10 RDA 2.055,1.704 2.376,1.880 0.320,0.177 10 5 1.73,1.796 1.946,1.973 0.217,0.177 10 +B 2.055,2.15 2.376,2.326 0.320,0.177 10 1 1.611,2.243 1.945,2.419 0.334,0.177 10 GND 5.22,0.805 5.637,0.982 0.417,0.177 10 PRG 5.22,1.293 5.622,1.470 0.402,0.177 10 RDA 4.967,0.709 5.325,0.885 0.357,0.177 10 5 4.967,1.211 5.385,1.387 0.417,0.177 10 4 5.264,2.39 6.379,2.716 1.115,0.326 10 Main Body ECU 3.179,2.281 4.052,2.461 0.872,0.181 10 from Battery 2.254,1.95 3.114,2.131 0.860,0.181 10 MPX-B NO.1


w/ Tire Pressure Warning System


B456778E01
0.448,5.188 3.656,5.385 3.208,0.198 10 false Door Control Receiver 2.802,3.542 6.01,3.74 3.208,0.198 10 false Tire Pressure Monitor Receiver Assembly 5.563,5.156 7.094,5.385 1.531,0.229 10 false Main Body ECU 5.563,4.99 7.094,5.219 1.531,0.229 10 false E118 2.802,3.344 4.333,3.573 1.531,0.229 10 false L75 0.448,5.01 1.979,5.24 1.531,0.229 10 false L47 1.365,4.25 2.896,4.479 1.531,0.229 10 false GND 1.76,4.104 3.292,4.333 1.531,0.229 10 false 1 1.385,2.969 2.917,3.198 1.531,0.229 10 false PRG 1.365,2.135 2.896,2.365 1.531,0.229 10 false RDA 1.469,0.833 3,1.063 1.531,0.229 10 false +B 1.74,0.708 3.271,0.938 1.531,0.229 10 false 5 1.76,2.031 3.292,2.26 1.531,0.229 10 false 2 1.75,2.875 3.281,3.104 1.531,0.229 10 false 3 3.01,2.042 4.542,2.271 1.531,0.229 10 false 10 3.031,2.875 4.563,3.104 1.531,0.229 10 false 9 2.375,0.979 3.906,1.208 1.531,0.229 10 false MPX-B NO. 1 3.802,0.813 5.333,1.042 1.531,0.229 10 false from Battery 4.458,2.042 5.99,2.271 1.531,0.229 10 false 4 5.552,2.052 7.083,2.281 1.531,0.229 10 false 4 4.479,2.854 6.01,3.083 1.531,0.229 10 false 5 5.552,2.854 7.083,3.083 1.531,0.229 10 false 5 5.729,2.156 7.125,2.406 1.396,0.25 10 false RDA 5.74,2.99 7.156,3.229 1.417,0.24 10 false PRG 3.99,2.156 5.385,2.406 1.396,0.25 10 false RDA2 3.24,2.156 4.635,2.406 1.396,0.25 10 false RDA3 3.26,2.969 4.792,3.198 1.531,0.229 10 false PRG3 4,2.948 5.531,3.177 1.531,0.229 10 false PRG2


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>REGISTRATION).

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver or tire pressure monitor receiver assembly if the door control receiver or tire pressure monitor receiver assembly has been replaced.*

for Initialization:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

for Registration:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

First, confirm that there are no malfunctions in the tire pressure warning system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU, make sure to replace it with a new one.

*: w/ Tire Pressure Warning System




PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Each door locks and unlocks normally.




OK

2.CHECK KEY REMINDER WARNING OPERATION

NG

2.CHECK KEY REMINDER WARNING OPERATION
a.

Check the key reminder warning buzzer operation.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK

HINT:

If the key reminder warning buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.


OK:

Key reminder warning buzzer operates normally.




OK

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

NG

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock control functions operate normally.




OK

4.CHECK TRANSMITTER BATTERY

NG

5.CHECK FOR ELECTRICAL NOISE
4.CHECK TRANSMITTER BATTERY
a.

Remove the battery from the inoperative door control transmitter assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Entry and Start System)>REPLACEMENT


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Always 2.5 to 3.2 V




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

5.CHECK FOR ELECTRICAL NOISE
a.

Move the transmitter in the vicinity of the door control receiver.

HINT:

Refer to Parts Location for the location of the door control receiver.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>PARTS LOCATION



b.

Press and hold either the lock or unlock transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter assembly closer to the door control receiver. Moving closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter assembly is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.




Result
Result Proceed to
OK A
NG (for Light Type) B
NG (for Buzzer Type) C


A

FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT

B

6.SWITCH TO SELF DIAGNOSTIC MODE

C

8.SWITCH TO SELF DIAGNOSTIC MODE
6.SWITCH TO SELF DIAGNOSTIC MODE
a.

Using GTS

i.

Connect the GTS to the DLC3.


ii.

Turn the Ignition switch to ON.


iii.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Door Lock Diagnosis Mode


iv.

Proceed to the next step in accordance with the prompts on the GTS screen.


v.
B220865E36
0.094,0.125 2.021,0.458 1.927,0.333 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false On 0.573,1.698 1.042,2.01 0.469,0.313 10 false Off 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.



b.

Not using GTS (for LHD)

i.

Insert and remove the key into/from the ignition key cylinder one time (Insert → Remove → Insert → Remove) and then ignition switch turn ON to off within 5 seconds.


ii.

Perform the following operations within 30 seconds.

(1) Turn the ignition switch from ON to off at nine times.


iii.
B220865E37
0.104,0.094 2.094,0.427 1.99,0.333 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false On 0.573,1.698 1.042,2.01 0.469,0.313 10 false Off 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.




NEXT

7.CHECK SELF DIAGNOSTIC MODE
7.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B456672E01
0.208,0.146 4.063,0.385 3.854,0.24 12 false Interior Light Output: 0.531,0.948 2.823,1.146 2.292,0.198 10 false Normal Wave (A): 0.521,1.24 2.813,1.438 2.292,0.198 10 false (Lock/Unlock Switch) 0.469,1.979 2.76,2.177 2.292,0.198 10 false On 0.479,2.365 2.771,2.563 2.292,0.198 10 false Off 1.219,2.781 3.51,2.979 2.292,0.198 10 false T1 1.729,2.792 4.021,2.99 2.292,0.198 10 false T2 0.677,3.5 2.969,3.698 2.292,0.198 10 false T1: 0.25 seconds (Interior Light) 0.677,3.823 2.969,4.021 2.292,0.198 10 false T2: 0.5 seconds (Interior Light) 4.271,3.385 6.563,3.583 2.292,0.198 10 false Off 4.281,1.563 6.573,1.76 2.292,0.198 10 false Off 4.313,1.146 6.604,1.344 2.292,0.198 10 false On 4.958,2.021 7.156,2.219 2.198,0.198 10 false Wave is being received 3.844,0.594 6.042,0.792 2.198,0.198 10 false Unmatching Recognition Code (B): 4.073,2.844 6.271,3.042 2.198,0.198 10 false No Diagnostic Output (C):


Result
Result Proceed to
Normal wave (light flash pattern) is output (A). A
Unmatching recognition code is output (B). B
No diagnostic outputs (C). C


A

B

10.CHECK REGISTER RECOGNITION CODE

C

11.CHECK DOOR CONTROL RECEIVER (RESPONSE)
8.SWITCH TO SELF DIAGNOSTIC MODE
a.

Using GTS

i.

Connect the GTS to the DLC3.


ii.

Turn the Ignition switch to ON.


iii.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.

Body Electrical > Main Body > Utility
Tester Display
Wireless Door Lock Diagnosis Mode


iv.

Proceed to the next step in accordance with the prompts on the GTS screen.


v.
B220865E79
0.115,0.135 3.073,0.5 2.958,0.365 12 false Wireless Door Lock Buzzer Output: 0.646,1.396 1,1.604 0.354,0.208 10 false ON 0.583,1.677 1.083,1.938 0.5,0.26 10 false OFF 1.552,2.167 1.844,2.385 0.292,0.219 10 false T1 2.146,2.167 2.396,2.375 0.25,0.208 10 false T2 1.969,2.583 3.354,3.021 1.385,0.438 10 false T1: 0.13 seconds 1.969,2.896 3.146,3.24 1.177,0.344 10 false T2: 0.25 seconds 1.802,2.167 2.083,2.427 0.281,0.26 10 false T1

Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern.



b.

Not using GTS (for LHD)

i.

Insert and remove the key into/from the ignition key cylinder one time (Insert → Remove → Insert → Remove) and then ignition switch turn ON to off within 5 seconds.


ii.

Perform the following operations within 30 seconds.

(1) Turn the ignition switch from ON to off at nine times.


iii.
B220865E79
0.115,0.135 3.073,0.5 2.958,0.365 12 false Wireless Door Lock Buzzer Output: 0.646,1.396 1,1.604 0.354,0.208 10 false ON 0.583,1.677 1.083,1.938 0.5,0.26 10 false OFF 1.552,2.167 1.844,2.385 0.292,0.219 10 false T1 2.146,2.167 2.396,2.375 0.25,0.208 10 false T2 1.969,2.583 3.354,3.021 1.385,0.438 10 false T1: 0.13 seconds 1.969,2.896 3.146,3.24 1.177,0.344 10 false T2: 0.25 seconds 1.802,2.167 2.083,2.427 0.281,0.26 10 false T1

Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern.




NEXT

9.CHECK SELF DIAGNOSTIC MODE
9.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the the sound patterns of the wireless door lock buzzer.

B357193E43
0.146,0.104 2.958,0.583 2.813,0.479 12 false Wireless Door Lock Buzzer Output: 0.177,1.021 2.469,1.219 2.292,0.198 10 false Normal Wave (A) 0.177,1.333 3.323,1.573 3.146,0.24 10 false (Lock/Unlock switch): 0.427,2.208 0.885,2.406 0.458,0.198 10 false OFF 0.427,1.833 0.885,2.031 0.458,0.198 10 false ON 1.208,2.604 1.667,2.802 0.458,0.198 10 false T1 1.719,2.615 2.177,2.813 0.458,0.198 10 false T2 0.698,3.198 3.844,3.438 3.146,0.24 10 false T1: 0.13 seconds (Wireless Door Lock Buzzer) 0.698,3.583 3.844,3.823 3.146,0.24 10 false T2: 0.25 seconds (Wireless Door Lock Buzzer) 4.115,0.448 6.406,0.646 2.292,0.198 10 false Unmatching Recognition Code (B): 4.146,0.99 4.604,1.188 0.458,0.198 10 false ON 4.156,1.396 4.615,1.594 0.458,0.198 10 false OFF 4.917,1.844 6.51,2.094 1.594,0.25 10 false Wave is being received 4.177,2.708 5.771,2.958 1.594,0.25 10 false No Diagnostic Output (C): 4.167,3.208 4.625,3.406 0.458,0.198 10 false OFF


Result
Result Proceed to
Normal wave (sound pattern) is output (A). A
Unmatching recognition code is output (B). B
No diagnostic outputs (C). C


A

B

10.CHECK REGISTER RECOGNITION CODE

C

11.CHECK DOOR CONTROL RECEIVER (RESPONSE)
10.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)>REGISTRATION

OK:

Recognition code can be registered.




OK

NG

15.REPLACE DOOR CONTROL RECEIVER
11.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter assembly from another vehicle.


b.

Press and hold down the door control transmitter assembly switch.


c.

Check that an unmatching recognition code is output.

OK:

Unmatching recognition code is not output.




OK

12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPLACE DOOR CONTROL TRANSMITTER

12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U164154E02
1.219,1.427 1.042,1.917 false 2.208,1.406 2.354,1.896 false 0.844,1.917 1.198,2.104 0.354,0.188 10 false GND 2.313,1.917 2.531,2.104 0.219,0.188 10 false +B 0.146,0.063 0.344,0.25 0.198,0.188 10 false *a 0.479,1.115 0.833,1.302 0.354,0.188 10 false L47

Disconnect the L47 door control receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-5 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)


OK

13.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B449857E01
0.635,1.396 0.99,1.635 0.354,0.24 2.01,2.24 1.75,1.938 true 0.698,1.438 1.156,1.635 0.458,0.198 10 false L47 2.063,2.177 2.521,2.375 0.458,0.198 10 false RDA 4.406,1.344 4.865,1.542 0.458,0.198 10 false 10 V 4.26,1.792 5.031,2.031 0.771,0.24 10 false Below 1 V 5.396,2.063 6.219,2.302 0.823,0.24 10 false 50 μsec. 5.271,0.875 6.719,1.104 1.448,0.229 10 false Transmitter Switch On 4.385,0.083 6.052,0.385 1.667,0.302 10 false RDA Output (Reference): 0.271,0.052 2.615,0.542 2.344,0.49 10 false Component with harness connected: (Door Control Receiver) 1.813,1.813 1.948,1.979 0.135,0.167 9 false 1 1.708,1.813 1.844,1.979 0.135,0.167 9 false 2 1.594,1.813 1.729,1.979 0.135,0.167 9 false 3 1.479,1.813 1.615,1.979 0.135,0.167 9 false 4 1.365,1.813 1.5,1.979 0.135,0.167 9 false 5

Measurement Condition
Item Content
Tester Connection L47-2 (RDA) - Body ground
Tool Setting 10 V/DIV., 50 μs/DIV.
Condition No key in ignition key cylinder, all doors closed and transmitter switch off → on

OK:

Waveform is output normally (refer to illustration).



Result
Result Proceed to
OK (w/o Tire Pressure Warning System) A
OK (w/ Tire Pressure Warning System) B
NG C


A

14.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)

B

18.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY)

C

REPLACE DOOR CONTROL RECEIVER

14.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
a.

Disconnect the L47 door control receiver connector.


b.

Disconnect the E118 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (RDA) - E118-4 (RDA) Always Below 1 Ω
L47-3 (PRG) - E118-5 (PRG) Always Below 1 Ω
L47-2 (RDA) - Body ground Always 10 kΩ or higher
L47-3 (PRG) - Body ground Always 10 kΩ or higher




OK

15.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL



NEXT

16.CHECK REGISTER RECOGNITION CODE
16.CHECK REGISTER RECOGNITION CODE

NEXT

17.CHECK DOOR CONTROL RECEIVER (OPERATION)
17.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.




OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

18.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TIRE PRESSURE MONITOR RECEIVER ASSEMBLY)
a.

Disconnect the L47 door control receiver connector.


b.

Disconnect the L75 tire pressure monitor receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (RDA) - L75-10 (RDA3) Always Below 1 Ω
L47-3 (PRG) - L75-9 (PRG3) Always Below 1 Ω
L47-2 (RDA) - Body ground Always 10 kΩ or higher
L47-3 (PRG) - Body ground Always 10 kΩ or higher




OK

19.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE MONITOR RECEIVER ASSEMBLY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE MONITOR RECEIVER ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the L75 tire pressure monitor receiver assembly connector.


b.

Disconnect the E118 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L75-4 (RDA2) - E118-4 (RDA) Always Below 1 Ω
L75-5 (PRG2) - E118-5 (PRG) Always Below 1 Ω
L75-4 (RDA2) - Body ground Always 10 kΩ or higher
L75-5 (PRG2) - Body ground Always 10 kΩ or higher




OK

20.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL



NEXT

21.CHECK REGISTER RECOGNITION CODE
21.CHECK REGISTER RECOGNITION CODE

NEXT

22.CHECK DOOR CONTROL RECEIVER (OPERATION)
22.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.




OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

23.REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY
23.REPLACE TIRE PRESSURE MONITOR RECEIVER ASSEMBLY
a.

Temporarily replace the tire pressure monitor receiver assembly with a new or known good one.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL



NEXT

24.CHECK REGISTER RECOGNITION CODE
24.CHECK REGISTER RECOGNITION CODE

NEXT

25.CHECK DOOR CONTROL RECEIVER (OPERATION)
25.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.




OK

END (TIRE PRESSURE MONITOR RECEIVER ASSEMBLY WAS DEFECTIVE)

NG