Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › from 2017.08
RM2660E _52 Drivetrain _066407 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0323663 AUTOMATIC TRANSMISSION ASSEMBLY A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 3.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C332155E02
1.323,0.75 0.979,0.094 0.979,0.094 0.875,0.094 true 1.167,2.448 0.917,3.063 0.917,3.063 0.771,3.063 true 2.792,0.219 2.948,0.396 0.156,0.177 10 false A 2.781,0.729 2.938,0.906 0.156,0.177 10 false *a 3.094,1.635 3.25,1.813 0.156,0.177 10 false *b 0.625,0 0.781,0.177 0.156,0.177 10 false *a 0.552,2.969 0.708,3.146 0.156,0.177 10 false *b

Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly (*a) and the torque converter assembly contact surface of the drive plate (*b).

Text in Illustration
*a Engine Surface
*b Drive Plate Surface


b.
C332156E02
0.854,0.344 0.552,0.146 0.552,0.146 0.844,0.49 true 0.333,0.01 0.49,0.188 0.156,0.177 10 false *a

Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

Text in Illustration
*a Matchmark

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C332157E02
3.021,0.969 3.177,1.146 0.156,0.177 10 false *1

Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C332158E02
3,0.99 3.156,1.167 0.156,0.177 10 false *1

Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the automatic transmission case sub-assembly and insert the key of the torque converter assembly into the groove of the oil pump drive gear.

Text in Illustration
*1 Front Oil Pump Oil Seal

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C332159E01
2.288,0.295 2.444,0.478 0.156,0.183 10 B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 6 harness clamp brackets with the 6 bolts.

C380140C01
2.875,2.26 3.073,2.469 0.198,0.208 10 false *a 6.198,2.313 6.396,2.521 0.198,0.208 10 false *a
V100135

Bolt A
V100136

Bolt B (Type A, Type B or Type C)
*a Bolt Head Length - -


Torque:
for bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt B (Type A) : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for bolt B (Type B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt B (Type C) : 13 N*m (133 kgf*cm, 10 ft.*lbf)

Bolt Head Length (Bolt B):
Item Bolt Head Length
Type A 4.0 mm (0.157 in.)
Type B 5.6 mm (0.220 in.)
Type C 6.0 mm (0.236 in.)



Hide 36100 5.INSTALL TRANSFER ASSEMBLY

Hide 36179 6.INSTALL LOWER TRANSFER CASE PROTECTOR

a.

Install the lower transfer case protector with the 7 bolts.

Torque:
13.6 N*m (139 kgf*cm, 10 ft.*lbf)


b.

Attach the clamp of the ground cable to the lower transfer case protector.


Hide 36407 7.INSTALL TRANSFER BREATHER HOSE SUB-ASSEMBLY

a.
C380092C01
1.01,2.625 1.146,2.625 1.146,2.625 1.813,1.781 true 1.615,3.135 1.865,3.135 1.865,3.135 2.104,1.896 true 3.198,3.104 3.198,2.927 3.198,2.927 2.969,2.469 true 0.792,2.531 1.01,2.771 0.219,0.24 10 false *1 1.406,3.052 1.615,3.292 0.208,0.24 10 false *1 3.104,3.115 3.354,3.344 0.25,0.229 10 false *1
*1 Breather Hose


Connect the 3 breather hoses and install the transfer breather hose sub-assembly to the automatic transmission assembly.


b.
C380091

Connect the 2 breather plug hoses to the harness clamp bracket.


Hide 35000 8.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

U165096E02
2.24,2.427 2.24,3.031 2.24,3.031 1.927,3.031 false 1.667,1.271 0.438,1.26 false 0.438,2.219 0.438,0.438 0.438,0.438 0.583,0.438 false 2.688,0 2.927,0.188 0.24,0.188 10 false *1 1.708,2.885 1.938,3.073 0.229,0.188 10 false *3 0.615,0.354 0.802,0.542 0.188,0.188 10 false *2

a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.

Confirm that the 2 knock pins are on the surface of the engine block that contacts the automatic transmission assembly.

Text in Illustration
*1 Torque Converter Assembly Centerpiece
*2 Knock Pin
*3 Crankshaft


c.
C380135C01
1.01,0.344 1.167,0.542 0.156,0.198 10 false -
V100135

Bolt A
V100136

Bolt B


Keeping the engine and automatic transmission assembly horizontal, align the knock pins with the holes on the automatic transmission assembly and install the 9 bolts shown in the illustration.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.




Hide 32943B 9.CONNECT TRANSMISSION OIL COOLER HOSE

a.
C380136C01
1.49,2.177 1.771,1.865 1.771,1.865 1.906,1.865 true 1.177,2.667 1.573,3.229 1.573,3.229 1.813,3.229 true 0.917,0.458 1,0.26 1,0.26 1.135,0.26 false 1.927,1.76 2.156,2.01 0.229,0.25 10 true *a 0.802,0.979 1.063,1.219 0.26,0.24 10 false *b 1.156,0.156 1.385,0.385 0.229,0.229 10 false *c 1.229,1.25 1.531,1.51 0.302,0.26 10 false 45° 1.229,1.625 1.531,1.885 0.302,0.26 10 false 45° 1.833,3.125 2.063,3.375 0.229,0.25 10 true *a
*a Paint Mark
*b 0 to 6.0 mm (0 to 0.236 in.)
*c 2.0 to 7.0 mm (0.0788 to 0.275 in.)


Connect the 2 transmission oil cooler hoses to the 2 oil cooler tube unions, and slide the 2 hose clips to secure the hose.

NOTICE:
·

Make sure the pinching portion of each hose clip is facing the direction shown in the illustration.

·

Make sure the paint mark of each hose is facing outward.




Hide 10.CONNECT OIL COOLER TUBE SUB-ASSEMBLY

a.
C380083N01
2.938,1.417 3.094,1.615 0.156,0.198 10 true A 0.344,0.042 0.5,0.24 0.156,0.198 10 true B

Temporarily install the oil cooler tube sub-assembly to the automatic transmission assembly and engine assembly with bolt A.


b.

Tighten bolt A, and then tighten bolt B.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 11.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the 13 wire harness clamps and wire harness.

C380134


b.

Connect the park/neutral position switch assembly connector, transmission wire connector, 2 transmission revolutions sensor connectors and 2 transfer control connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



c.
C380089

Install the 5 wire harness clamps.


d.

Tilt up the automatic transmission assembly.


e.
C171503

Connect the ground cable with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



Hide 12371 12.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 51203 13.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Connect the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.

Install the No. 3 frame crossmember sub-assembly to the frame with the 4 bolts and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


Hide 32101A 14.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the remaining 5 silver colored bolts.



Hide 11363A 15.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 28100 16.INSTALL STARTER ASSEMBLY

Hide 33702B 17.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

a.
C380067C01
2.01,1.073 2.302,1.354 2.302,1.354 2.594,1.354 false 2.625,1.26 2.844,1.479 0.219,0.219 10 false *1 2.292,0.25 2.49,0.458 0.198,0.208 10 false N 1.51,0.021 1.667,0.219 0.156,0.198 10 false P 1.906,0.375 2.063,0.573 0.156,0.198 10 false R
*1 Transmission Control Shaft Lever RH


Turn the transmission control shaft lever RH counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


b.
C380061

Connect the floor shift gear shifting rod sub-assembly to the transmission control shaft lever RH with the pin and a new clip.


Hide 17104 18.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17105 19.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 37110 20.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 21.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 24.INSPECT SHIFT LEVER POSITION

a.

When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.


b.

Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.


c.

Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after moving the shift lever to R.

If there are problems during the above inspections, perform the adjustment using the following procedures.

i.

Move the shift lever to N


ii.
C172428E02
1.175,0.153 1.357,0.330 0.182,0.177 10 *1 1.954,0.439 1.501,0.237 1.501,0.237 1.365,0.237 false

Loosen the nut of the floor shift gear shifting rod sub-assembly. Then, with the lever of the transmission floor shift assembly lightly pushed towards the rear of the vehicle, tighten the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 Shift Lever



Hide 53784 26.INSTALL FRONT FENDER APRON TRIM PACKING C

Hide 53782 27.INSTALL FRONT FENDER APRON TRIM PACKING A

Hide 51442 28.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51405A 29.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 30.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 31.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH