When the retractable outer mirror switch is set to auto (neutral position), an auto signal is detected by the main body ECU (multiplex network body ECU). When locking and unlocking all doors with the engine switch off, the main body ECU (multiplex network body ECU) sends return/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly returns and retracts the outer rear view mirror assembly based on the received signals.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.
Check power retract mirror function.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>OPERATION CHECK
Power retract mirror function is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wireless door lock control system.
Wireless door lock control system is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the smart entry and start system (for Entry Function).
Smart entry and start system (for Entry Function) is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List. (See pageVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Auto Mirror SW | Retractable outer mirror switch signal / ON or OFF | ON: Retractable outer mirror switch in auto position
OFF: Retractable outer mirror switch not in auto position |
- |
On the GTS screen, ON or OFF is displayed for each item according to the table above.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Remove the retractable outer mirror switch.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL
Inspect the retractable outer mirror switch.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G26 retractable outer mirror switch connector.
Disconnect the E117 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G26-2 (MR) - E117-14 (RET) | Always | Below 1 Ω |
| G26-3 (MAT) - E117-15 (AMR) | Always | Below 1 Ω |
| G26-4 (E) - Body ground | Always | Below 1 Ω |
| G26-2 (MR) or E117-14 (RET) - Body ground | Always | 10 kΩ or higher |
| G26-3 (MAT) or E117-15 (AMR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG