Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER(for LHD) › from 2018.08
RM2660E _52 Drivetrain _052808 CLUTCH _0255312 CLUTCH MASTER CYLINDER(for LHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 31410 1.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.
C403551

Install the clutch master cylinder with the 2 bolts.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)


b.
C403552E01
0.563,1.844 1.938,2.042 1.375,0.198 10 false MP grease

Apply MP grease to the contact surface of the clevis pin and clevis bush.


c.

Install the wave washer to the clevis pin.


d.

Connect the clevis of the master cylinder assembly to the clutch pedal sub-assembly with the clevis pin.


e.

Install a new clip to the clevis pin.


Hide 84520 2.INSTALL CLUTCH START SWITCH ASSEMBLY

C173223

a.

Install the clutch start switch assembly to the clutch pedal support sub-assembly, and then temporarily install the 2 nuts.

HINT:

The 2 nuts will be tightened to a torque specification in the "Adjust Clutch Start Switch Assembly" procedure.



Hide 31481J 3.INSTALL CLUTCH MASTER CYLINDER TO WAY TUBE

C403553E01
1.49,1.135 3.427,1.5 1.938,0.365 10 true Torque Wrench Fulcrum Length

a.

Using a union nut wrench, install the tube to the clutch master cylinder and clutch pedal support way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)




Hide 31434 4.INSTALL CLUTCH RESERVOIR HOSE

C403554

a.

Install the clutch reservoir hose to the clutch master cylinder assembly and clutch pedal support way with 2 new clips.

NOTICE:

Connect the clutch reservoir hose so that it will not be twisted.



Hide 55107A 5.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER

Hide 31481 6.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE

Hide 82733A 7.INSTALL MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

Hide 8.FILL RESERVOIR WITH BRAKE FLUID

Hide 31301 10.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY

Hide 84520 11.ADJUST CLUTCH START SWITCH ASSEMBLY

a.
C403555

While depressing the clutch pedal, tighten the 2 nuts so that the clearance between the clutch pedal and clutch start switch is within the specification.

Standard clearance between clutch pedal and clutch start switch:

4.1 to 6.1 mm (0.162 to 0.240 in.)


Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12.CHECK FLUID LEVEL IN RESERVOIR

Hide 13.INSPECT FOR CLUTCH FLUID LEAK

Hide 55303B 14.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 73900 15.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)