83520
1.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
89422
2.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11415
3.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the cylinder block water drain cock plug from the cylinder block water drain cock.
Remove the cylinder block water drain cock from the cylinder block.
11301M
4.REMOVE VVT SENSOR (for Intake Side of Bank 1)
11301M
5.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)
11301M
6.REMOVE VVT SENSOR (for Intake Side of Bank 2)
11301M
7.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)
11401G
8.REMOVE CRANKSHAFT POSITION SENSOR
15330B
9.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)
15330B
10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)
15330B
11.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)
15340
12.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)
12185
13.REMOVE OIL FILLER CAP HOUSING
Remove the oil filler cap.
Remove the 2 nuts, oil filler cap housing and gasket.
15771
14.REMOVE NO. 1 OIL PIPE
15772
15.REMOVE NO. 2 OIL PIPE
16.REMOVE OIL FILTER ELEMENT
15671
17.REMOVE OIL FILTER BRACKET
16323
18.REMOVE WATER INLET HOUSING
16356
19.REMOVE REAR WATER BY-PASS JOINT
Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.
Remove the O-ring from the No. 1 water outlet pipe.
19100P
20.REMOVE SPARK PLUG
12204
21.REMOVE PCV VALVE SUB-ASSEMBLY
13471
22.REMOVE CRANKSHAFT PULLEY
11202
23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
11201
24.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
11193
25.REMOVE SPARK PLUG TUBE GASKET
Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
|
Pry |
Remove the 6 spark plug tube gaskets.
Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.
89491
26.REMOVE ENGINE OIL LEVEL SENSOR
12101A
27.REMOVE OIL PAN DRAIN PLUG
Remove the drain plug and gasket.
12102A
28.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
15104
29.REMOVE OIL STRAINER SUB-ASSEMBLY
12101
30.REMOVE OIL PAN SUB-ASSEMBLY
12121
31.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 6 bolts and No. 1 oil pan baffle plate.
11381
32.REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 5 bolts and 2 nuts.
Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.
| *a | Pry |
Tape the screwdriver tip before use.
11381A
33.REMOVE REAR CRANKSHAFT OIL SEAL
Using a screwdriver and hammer, tap out the oil seal.
Be careful not to damage the rear oil seal retainer.
11302
34.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
16100
35.REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 8 bolts, engine water pump and gasket.
11301C
36.REMOVE FRONT CRANKSHAFT OIL SEAL
37.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Temporarily install the pulley set bolt.
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
| *1 | Timing Mark |
13540
38.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
| *3 | Pin |
Move the stopper plate downward to set the lock, and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly.
13559
39.REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper.
13506
40.REMOVE CHAIN SUB-ASSEMBLY
Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
Remove the pulley set bolt.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly.
| *A | for Bank 1 |
13581
41.REMOVE NO. 1 IDLE GEAR SHAFT
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
13561
42.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
13562
43.REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 No. 2 chain vibration dampers.
13521
44.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket.
45.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.
13550
46.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly.
47.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the camshaft and No. 2 camshaft.
11103C
48.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
| *1 | Protective Tape |
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.
Tape the screwdriver tip before use.
49.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.
13560A
50.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly.
51.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Check that the camshafts are positioned as shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the No. 3 camshaft and No. 4 camshaft.
11104A
52.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
| *1 | Protective Tape |
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.
Tape the screwdriver tip before use.
13801
53.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 24 valve rocker arms from the cylinder head.
Arrange the removed parts in the correct order.
13750
54.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 24 valve lash adjusters from the cylinder head.
Arrange the removed parts in the correct order.
13716
55.REMOVE VALVE STEM CAP
Remove the 24 valve stem caps from the cylinder head.
Arrange the removed parts in the correct order.
11101
56.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11102
57.REMOVE CYLINDER HEAD LH
11115
58.REMOVE CYLINDER HEAD GASKET
11116
59.REMOVE NO. 2 CYLINDER HEAD GASKET
16332
60.REMOVE NO. 1 WATER OUTLET PIPE
89615
61.REMOVE KNOCK CONTROL SENSOR
62.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 water jacket spacers from the cylinder head.
Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.
63.REMOVE STRAIGHT PIN
It is not necessary to remove a straight pin unless it is being replaced.
64.REMOVE RING PIN
It is not necessary to remove a ring pin unless it is being replaced.
65.REMOVE STUD BOLT
It is not necessary to remove a stud bolt unless it is being replaced.