Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0467501 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat belt set (for driver side).

WIRING DIAGRAM

C380578E24
4.458,0.958 5.073,1.156 0.615,0.198 10 false BKL 4.156,0.906 4.771,1.104 0.615,0.198 10 false 23 4.427,1.885 5.042,2.083 0.615,0.198 10 false I6 4.406,2.063 6.542,2.323 2.135,0.26 10 false Combination Meter Assembly 1.313,1.51 3.24,2.083 1.927,0.573 10 false Front Seat Inner Belt Assembly (for driver side) 1.313,1.333 2.667,1.583 1.354,0.25 10 false S29*1, Q46*2 2.479,0.844 3.094,1.042 0.615,0.198 10 false 1 1.323,0.854 1.938,1.052 0.615,0.198 10 false 2 1.542,0.854 2.156,1.052 0.615,0.198 10 false E 2.271,0.844 2.885,1.042 0.615,0.198 10 false + 0.188,2.083 1.875,2.281 1.688,0.198 10 false *1: for LHD 0.208,2.406 1.896,2.604 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system and CXPI communication system. First, confirm that there is no malfunction in the CAN communication system and CXPI communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



HINT:
·

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK

·

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT WARNING)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Warning Front seat belt warning light ON or OFF -
OK:

The GTS display changes correctly in response to the warning light condition.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (DRIVER BUCKLE SWITCH)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (DRIVER BUCKLE SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Buckle Switch Driver side seat belt buckle switch status Fastened or Not Fastened Fastened: Driver side seat belt fastened
Not Fastened: Driver side seat belt not fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Buckle Switch
50003 409 26
OK:

The GTS display changes correctly in response to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.INSPECT FRONT SEAT BELT SET (FOR DRIVER SIDE)
3.INSPECT FRONT SEAT BELT SET (FOR DRIVER SIDE)

OK

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR DRIVER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR DRIVER SIDE) - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the S29*1 or Q46*2 front seat belt set (for driver side) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the I6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(S29,I6)Location & Routing

Click Connector(S29)Seat>No. 2 Floor Wire>Front Seat Belt Set LH

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

S29-1 (+) - I6-23 (BKL) Always Below 1 Ω
S29-2 (E) - Body ground Always Below 1 Ω
S29-1 (+) or I6-23 (BKL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(Q46,I6)Location & Routing

Click Connector(Q46)Seat>Floor Wire>Front Seat Belt Set RH

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Q46-1 (+) - I6-23 (BKL) Always Below 1 Ω
Q46-2 (E) - Body ground Always Below 1 Ω
Q46-1 (+) or I6-23 (BKL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR