| *A | w/ Spacer | *B | w/ Rear No. 2 Seat, Curtain Shield Airbag |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | NO. 4 COOLER UNIT DRAIN HOSE | 88539N | - | - | - |
| 9 | NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR | 58723B | - | - | - |
| 10 | REAR BUMPER ASSEMBLY | - | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Compressor oil ND-OIL 8 or equivalent | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | INNER ROOF SIDE GARNISH RH | 62471A | - | - | - |
| 18 | QUARTER TRIM PANEL ASSEMBLY RH | 62510M | - | - | - |
| 19 | NO. 1 TONNEAU COVER HOLDER CAP | 64937A | - | - | - |
| 20 | REAR DOOR SCUFF PLATE RH | 67917C | - | - | - |
| 21 | REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) | 73560 | - | - | - |
| 22 | REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) | 73360C | - | - | - |
| 23 | OUTER LAP BELT ANCHOR COVER | 73233 | - | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/ Rear No. 2 Seat, Curtain Shield Airbag |
| *C | w/ Tonneau Cover | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 24 | REAR FLOOR MAT REAR SUPPORT PLATE | 58574G | - | - | - |
| 25 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 26 | REAR FLOOR BOARD REAR RH | 58417B | - | - | - |
| 27 | REAR FLOOR BOARD REAR LH | 58418H | - | - | - |
| 28 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 29 | REAR DECK TRIM COVER | 64716P | - | - | - |
| 30 | ROPE HOOK ASSEMBLY | 66310N | - | - | - |
| 31 | TONNEAU COVER ASSEMBLY | 64910M | - | - | - |
| 32 | REAR NO. 2 SEAT ASSEMBLY RH | - | - | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/o Rear No. 2 Seat |
| *C | w/ Tonneau Cover | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 33 | REAR WHEEL HOUSE LINER RH | 65637B | - | - | - |
| 34 | REAR BUMPER SIDE SEAL RH | 52591 | ( ) |
- | - |
| 35 | QUARTER PANEL REAR MUDGUARD RH | 76625G | - | - | - |
| 36 | WHEEL ASSEMBLY | - | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 37 | CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT | - | ( ) |
- | - |
| 38 | WARM UP ENGINE | - | ( ) |
- | - |
| 39 | INSPECT FOR REFRIGERANT LEAK | - | ( ) |
- | - |
| 40 | UPPER RADIATOR SUPPORT SEAL | 53292A | - | - | - |
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
62170A 5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH (w/ Rear No. 2 Seat, Curtain Shield Airbag)
62495B 6.INSTALL NO. 2 ROOF SIDE INNER GARNISH SPACER RH (w/ Spacer)
7.INSTALL ROOF HEADLINING ASSEMBLY
88539N 8.INSTALL NO. 4 COOLER UNIT DRAIN HOSE
58723B 9.INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR
10.INSTALL REAR BUMPER ASSEMBLY
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (for Standard)>INSTALLATION
for Aero Type:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (for Aero Type)>INSTALLATION
87030 11.INSTALL AIR CONDITIONING BLOWER ASSEMBLY
| *a | Protrusion | *b | Cutout |
Align the cutout of the No. 2 cooler unit drain hose with the protrusion of the air conditioning blower assembly and install the No. 2 cooler unit drain hose.
Install the air conditioning blower assembly with the 4 bolts and tighten the bolts in the order shown in the illustration.
Connect the connector.
Install the 2 bolts.
88717Z 12.CONNECT NO. 2 SUCTION TUBE
Connect the No. 2 suction tube using the following procedure.
1. Remove the vinyl tape from the No. 2 suction tube and then apply a sufficient amount of compressor oil to new O-rings and the fitting surface of the No. 2 suction tube and air conditioning blower assembly.
ND-OIL 8 or equivalent
2. Install the O-ring to the No. 2 suction tube.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
3. Connect the No. 2 suction tube with the bolt.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
88G16N 13.CONNECT NO. 2 LIQUID TUBE
Connect the No. 2 liquid tube using the following procedure.
1. Remove the vinyl tape from the No. 2 liquid tube and then apply a sufficient amount of compressor oil to new O-rings and the fitting surface of the No. 2 liquid tube and air conditioning blower assembly.
ND-OIL 8 or equivalent
2. Install the O-ring to the No. 2 liquid tube.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
3. Connect the No. 2 liquid tube with the bolt.
Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed.)
87217N 14.INSTALL REAR NO. 9 SIDE AIR DUCT
15.INSTALL COOLER PLATE
82161 16.CONNECT FLOOR WIRE
62471A 17.INSTALL INNER ROOF SIDE GARNISH RH
62510M 18.INSTALL QUARTER TRIM PANEL ASSEMBLY RH
64937A 19.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
67917C 20.INSTALL REAR DOOR SCUFF PLATE RH
73560 21.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>INSTALLATION
73360C 22.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>INSTALLATION
73233 23.INSTALL OUTER LAP BELT ANCHOR COVER
58574G 24.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 25.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58417B 26.INSTALL REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58418H 27.INSTALL REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58410B 28.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 29.INSTALL REAR DECK TRIM COVER (w/o Rear No. 2 Seat)
66310N 30.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
64910M 31.INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat, w/ Tonneau Cover)
32.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>INSTALLATION
65637B 33.INSTALL REAR WHEEL HOUSE LINER RH
76625G 35.INSTALL QUARTER PANEL REAR MUDGUARD RH
36.INSTALL WHEEL ASSEMBLY
37.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
38.WARM UP ENGINE
39.INSPECT FOR REFRIGERANT LEAK
53292A 40.INSTALL UPPER RADIATOR SUPPORT SEAL