Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0468066 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear axle hub bolt removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE REAR WHEEL

Hide 46170 4.REMOVE PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 890C0A 5.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 47850 6.DISCONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

Hide 42431 7.REMOVE REAR DISC

Hide 42312E 8.REMOVE REAR AXLE HUB BOLT LH

a.
C456657C02
1.635,0.74 1.635,1.073 false 2.521,0.635 2.5,0.865 false 2.427,0.521 2.75,0.667 0.323,0.146 10 true SST 2.865,1.521 3.063,1.698 0.198,0.177 10 true *c 1.615,1.938 1.823,2.104 0.208,0.167 10 true *b 1.5,0.583 1.708,0.74 0.208,0.156 10 true *a
*a Service Nut
*b Hold
*c Turn


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09650-17011  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 9.INSTALL REAR AXLE HUB BOLT LH

a.
C456658C02
2.677,0.542 2.677,0.292 false 3.01,0.719 3.01,0.542 false 0.906,1.917 1.125,2.083 0.219,0.167 10 true *c 1.844,1.396 2.042,1.563 0.198,0.167 10 true *d 2.906,0.375 3.115,0.542 0.208,0.167 10 true *a 2.604,0.104 2.833,0.281 0.229,0.177 10 true *b
*a Service Nut
*b Washer
*c Hold
*d Turn


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install the washer and service nut to the rear axle hub bolt as shown in the illustration.

HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 10.INSTALL REAR DISC

Hide 47850 11.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

Hide 890C0A 12.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Hide 46170 13.INSTALL PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY (w/ PARKING BRAKE ACTUATOR PROTECTOR ASSEMBLY)

Hide 14.INSTALL REAR WHEEL

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART