Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P003012  HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery  P003013  HO2S Heater Control Bank 1 Sensor 1 Circuit Open  P005012  HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery  P005013  HO2S Heater Control Bank 2 Sensor 1 Circuit Open  P101A9E  A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On  P103A9E  A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On  


DESCRIPTION

Refer to DTC P223711.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P223711

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A285791E38
0.104,0.052 3.313,0.292 3.208,0.24 10 false Reference (System Diagram of Bank 1 Sensor 1): 0.042,1.146 0.958,1.49 0.917,0.344 10 false from SUB R/B-NO.1 Fuse 1.979,2.344 2.75,2.698 0.771,0.354 10 false A/F 3.375,2.01 4.771,2.188 1.396,0.177 10 false Air Fuel Ratio Sensor 3.385,1.021 3.656,1.271 0.271,0.25 10 false +B 3.281,1.531 3.604,1.708 0.323,0.177 10 false A1A- 4.448,1.01 4.823,1.188 0.375,0.177 10 false HA1A 4.99,1 5.365,1.177 0.375,0.177 10 false HA1A 4.448,1.542 4.813,1.719 0.365,0.177 10 false A1A+ 5.01,1.521 5.375,1.698 0.365,0.177 10 false A1A+ 5.021,2.094 5.344,2.271 0.323,0.177 10 false A1A- 5.656,3.26 5.979,3.438 0.323,0.177 10 false ECM 6.177,1.615 6.76,1.958 0.583,0.344 10 false Duty Control 1.094,1.302 1.802,1.5 0.708,0.198 10 false A/F HTR 3.813,0.813 4.25,0.99 0.438,0.177 10 false Heater 3.802,1.302 4.26,1.479 0.458,0.177 10 false Sensor 0.24,2.063 1.063,2.427 0.823,0.365 10 false from EFI-B NO. 2 Fuse



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003012 HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0032
P003013 HO2S Heater Control Bank 1 Sensor 1 Circuit Open Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0031
P005012 HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0052
P005013 HO2S Heater Control Bank 2 Sensor 1 Circuit Open Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

A/F relay

·

ECM


Comes on SAE: P0051
P101A9E A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 1 sensor 1) heater circuit

·

ECM


Comes on SAE: P101D
P103A9E A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (bank 2 sensor 1) heater circuit

·

ECM


Comes on SAE: P103D

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

CONFIRMATION DRIVING PATTERN

A262623E02
0.792,0.969 1.583,1.26 0.792,0.292 10 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 Idling 0.229,2.01 1.396,2.354 1.167,0.344 10 Ignition Switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P003012, P003013, P005012, P005013, P101A9E or P103A9E.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1 and A/F (O2) Sensor Heater Duty Ratio B2S1].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P013613). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT A/F RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C87,C92,C88)Location & Routing

Click Connector(C87)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C88)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

C87-1 (HA1A) - C92-22 (HA1A) Always Below 1 Ω
C88-1 (HA2A) - C92-45 (HA2A) Always Below 1 Ω
C87-1 (HA1A) or C92-22 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C88-1 (HA2A) or C92-45 (HA2A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E)
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P003012, P003013, P005012, P005013, P101A9E OR P103A9E is output B




A

B

5.INSPECT A/F RELAY

Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)

NG

REPLACE A/F RELAY

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF A/F RELAY)
a.
A485543C02
0.094,0.104 0.406,0.302 0.313,0.198 10 false *1 2.26,2.417 2.573,2.615 0.313,0.198 10 false *a
*1 Engine Room Relay Block No. 2
*a A/F Relay terminal


Remove the A/F relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (A/F relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, EFI MAIN NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F RELAY - BATTERY)

7.CHECK HARNESS AND CONNECTOR (A/F RELAY - AIR FUEL RATIO SENSOR, EFI MAIN NO.1 RELAY)
a.

Remove the A/F relay.


b.

Remove the EFI MAIN NO.1 relay.


c.

Disconnect the air fuel ratio sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C87,C88)Location & Routing

Click Connector(C87)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 1 Sensor 1)

Click Connector(C88)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Fuel Ratio Sensor (Bank 2 Sensor 1)

3 (A/F relay) - C87-2 (+B) Always Below 1 Ω
3 (A/F relay) - C88-2 (+B) Always Below 1 Ω
2 (A/F relay) - 3 (EFI MAIN NO.1 relay) Always Below 1 Ω
1 (A/F relay) - Body ground Always Below 1 Ω
3 (A/F relay) or C87-2 (+B) - Body ground Always 10 kΩ or higher
3 (A/F relay) or C88-2 (+B) - Body ground Always 10 kΩ or higher
2 (A/F relay) or 3 (EFI MAIN NO.1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR