Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P219519  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold  P219524  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck High  P219618  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold  P219623  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck Low  P219719  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Above Threshold  P219724  A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck High  P219818  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Below Threshold  P219823  A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck Low  


DESCRIPTION

Refer to DTC P223711.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P223711

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P219519 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2195
P219524 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck High Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.21 V or higher.
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2195
P219618 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2196
P219623 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck Low Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V.
(b) Heated oxygen sensor voltage is less than 0.71 V.
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2196
P219719 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Above Threshold While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2197
P219724 A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck High Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.21 V or higher.
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2197
P219818 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Below Threshold While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2198
P219823 A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck Low Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V.
(b) Heated oxygen sensor voltage is less than 0.71 V.
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Intake system

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on SAE: P2198

HINT:
·

DTCs P219519, P219524, P219618 and P219623 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.

·

DTCs P219719, P219724, P219818 and P219823 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.

·

When any of these DTCs are stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage or Accelerator Position Sensor No.2 Voltage.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.



MONITOR DESCRIPTION

Sensor Voltage Detection Monitor:

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being less than 0.71 V, the ECM stores DTC P219623 or P219823. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P219524 or P219724 is stored.


Sensor Current Detection Monitor:

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P219519 or P219719 (stuck on high side). If the air fuel ratio sensor output is less than 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P219618 or P219818 (stuck on low side).


A284399E03
2.385,2.281 2.188,1.594 2.188,1.594 2.323,1.594 false 4.406,2.281 4.26,1.667 4.26,1.667 4.396,1.667 false 5.771,2.281 5.677,1.656 5.677,1.656 5.813,1.656 false 0.177,0.115 2.76,0.323 2.583,0.208 10 Air Fuel Ratio Sensor Current Monitor 2.833,0.323 6.094,0.51 3.26,0.188 10 Cumulative Time "t" = t1 + t2 = 3 seconds or more 1.469,1.208 1.854,1.396 0.385,0.188 10 OFF 1.49,0.917 1.875,1.104 0.385,0.188 10 ON 0.646,1.073 1.24,1.281 0.594,0.208 10 Fuel-cut 0.448,2.833 1.802,3.104 1.354,0.271 10 High Side Threshold 2.375,1.51 3.729,1.781 1.354,0.271 10 Delay (3 seconds) 0.49,3.49 1.844,3.76 1.354,0.271 10 Low Side Threshold 0.479,2.219 1.833,2.49 1.354,0.271 10 Sensor Current (mA) 4.448,1.563 5.802,1.833 1.354,0.271 10 Delay (3 seconds) 5.865,1.563 7.073,1.823 1.208,0.26 10 Delay (3 seconds) 6.01,3.813 6.292,4.031 0.281,0.219 10 t2 4.708,3.813 4.99,4.031 0.281,0.219 10 t1 2.385,3.635 3.74,3.906 1.354,0.271 10 3 seconds or more 4.708,4.24 6.365,4.427 1.656,0.188 10 Abnormal Sensor Output 2.417,4.25 4.073,4.438 1.656,0.188 10 Normal Sensor Output 6.667,4.26 7.031,4.448 0.365,0.188 10 Time

CONFIRMATION DRIVING PATTERN

A283818E22
2.917,1.51 3.115,0.198 3.115,0.198 2.865,0.198 true 5.448,1.667 5.75,0.583 true 5.021,1.521 4.5,1.521 false 6.333,2.25 5.375,2.25 false 4.052,3.531 3.823,3.354 true 4.927,1.677 4.5,0.583 true 5.542,3.167 5.708,3.167 5.708,3.167 5.5,2.74 true 4.708,2.958 4.875,2.958 4.875,2.958 4.99,2.729 true 1.76,2.375 2.521,0.542 2.521,0.542 2.271,0.542 true 0.469,0.354 2.354,0.708 1.885,0.354 10 false Engine Coolant Temperature: 75°C or higher 0.156,0.865 1.104,1.094 0.948,0.229 10 false Vehicle Speed 1.219,0.083 2.854,0.5 1.635,0.417 10 false Between 60 and 100 km/h 0.719,2.281 1.167,2.583 0.448,0.302 10 false Idling 1.25,2.865 2.083,3.083 0.833,0.219 10 false Warming up 2.49,2.875 3.219,3.396 0.729,0.521 10 false 10 minutes or more 3.427,1.458 4.479,1.854 1.052,0.396 10 false 60 km/h or more 3.396,0.448 4.542,0.865 1.146,0.417 10 false Accelerator Pedal Depressed 4.667,0.708 5.667,0.917 1,0.208 10 false At least 3 times 5.823,0.438 7.052,0.958 1.229,0.521 10 false Accelerator Pedal Released (Fuel-cut) 6.417,2.146 6.979,2.51 0.563,0.365 10 false 10 km/h 6.25,2.552 6.667,2.802 0.417,0.25 10 false Time 4.375,3.073 5.604,3.344 1.229,0.271 10 false 4 seconds or more 4.094,3.469 5.417,3.667 1.323,0.198 10 false Refer to figure below 3.458,2.865 4.74,3.229 1.281,0.365 10 false 10 seconds or more 1.552,2.167 1.813,2.385 0.26,0.219 10 false [A] 2.708,1.302 2.969,1.521 0.26,0.219 10 false [B] 3.844,2.167 4.083,2.417 0.24,0.25 10 false [C] 4.99,1.302 5.25,1.521 0.26,0.219 10 false [D] 5.5,1.594 5.76,1.813 0.26,0.219 10 false [E] 6.083,3.115 6.344,3.333 0.26,0.219 10 false [F]

A268862E08
3.646,2.625 3.958,0.885 false 3.375,2.625 2.167,0.719 2.167,0.719 2.292,0.719 false 0.104,0.042 3.042,0.24 2.938,0.198 10 false Driving Pattern Detail for [C] through [E]: 0.188,0.552 1.958,0.75 1.771,0.198 10 false Reference Engine Speed 2.823,0.156 7,0.406 4.177,0.25 10 false Cumulative Detection Period "t" = t1 + t2 + t3 = 3 seconds or more 1.094,2.365 1.51,2.563 0.417,0.198 10 false Idling 2.188,2.948 2.698,3.229 0.51,0.281 10 false Idling 3.177,3.115 3.833,3.479 0.656,0.365 10 false 4 seconds or more 2.188,2.25 2.448,2.521 0.26,0.271 10 false [C] 3.031,1.146 3.313,1.469 0.281,0.323 10 false [D] 3.469,1.542 3.729,1.813 0.26,0.271 10 false [E] 2.375,0.635 3.563,0.833 1.188,0.198 10 false Delay (3 seconds) 4.01,0.75 5.448,0.948 1.438,0.198 10 false Detection Period t1 4.813,2.375 4.99,2.625 0.177,0.25 10 false t2 6.042,2.396 6.302,2.635 0.26,0.24 10 false t3 6.49,2.781 6.875,2.979 0.385,0.198 10 false Time 4.375,3.115 5.031,3.479 0.656,0.365 10 false 4 seconds or more 5.604,3.115 6.26,3.479 0.656,0.365 10 false 4 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for at least 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Using the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine / Data List / All Data / Idle Fuel Cut.

10.

With the shift state S selected [C], accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

HINT:

While "Idle Fuel Cut" on the Data List is ON, fuel-cut control is being executed.


12.

Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

13.

Repeat steps [C] through [E] above at least 3 times in one driving cycle.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 OR P219823)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output A
DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 and P013613, P013617, P01361C, P015613, P015617 or P01561C are output
DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)

NO

4.READ VALUE USING GTS (AFS CURRENT B1S1 AND AFS CURRENT B2S1)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output)
B




A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING GTS (AFS CURRENT B1S1 AND AFS CURRENT B2S1)
4.READ VALUE USING GTS (AFS CURRENT B1S1 AND AFS CURRENT B2S1)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.

Powertrain > Engine > Data List
Tester Display
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B2S1
50003 372 230,432
HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.



Result:
Result Proceed to
Within normal range
(0.7 mA or higher, and lower than 2.2 mA)
A
Outside normal range
(lower than 0.7 mA, or 2.2 mA or higher)
B




A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

15.REPLACE AIR FUEL RATIO SENSOR
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Start the engine.


b.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


c.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
50004 372 8 225,512,218,510

d.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2 or A/F (O2) Sensor Voltage B2S1 and O2 Sensor Voltage B2S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Voltage B1S1
A/F (O2) Sensor Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2 Sensor Voltage B1S2
O2 Sensor Voltage B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result:
Status of A/F (O2) Sensor Voltage B1S1 or A/F (O2) Sensor Voltage B2S1 Status of O2 Sensor Voltage B1S2 or O2 Sensor Voltage B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltages (A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2) are consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, A/F (O2) Sensor Voltage B1S1 and A/F (O2) Sensor Voltage B2S1 are consistently below 3.1 V, and O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2 are consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1, A/F (O2) Sensor Voltage B2S1, O2 Sensor Voltage B1S2 and O2 Sensor Voltage B2S2].

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

6.CHECK INTAKE SYSTEM

B

15.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

14.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output)
A
NORMAL
(DTCs are not output)
B




A

12.REPLACE ECM

B

END

12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit




Result:
Proceed to
NEXT



NEXT

END

14.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE

15.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P219519, P219524, P219618, P219623, P219719, P219724, P219818 or P219823 is output)
B




A

END

B