|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease |
|
Do not apply lubricants to the threads parts |
| *1 | OIL CONTROL VALVE FILTER LH | *2 | OIL CONTROL VALVE FILTER RH |
| *3 | SEAL WASHER | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
| *A | for Separate Type | *B | for Integrated Type |
| *1 | ENGINE OIL LEVEL DIPSTICK | *2 | NO. 2 IDLER PULLEY COVER PLATE |
| *3 | IDLER PULLEY COVER PLATE | *4 | NO. 1 WATER BY-PASS HOSE |
| *5 | NO. 2 WATER BY-PASS HOSE | *6 | NO. 3 WATER BY-PASS HOSE |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Do not apply lubricants to the threads parts | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 20 | NO. 2 EMISSION CONTROL VALVE SET | 25702B | ( ) |
- | - |
| 21 | NO. 1 EMISSION CONTROL VALVE SET | 25701B | ( ) |
- | - |
| 22 | ENGINE ASSEMBLY | - | - | - | - |
| *A | w/ Secondary Air Injection System | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
11302 1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
| *a | Cylinder Head Sub-assembly and Cylinder Block Sub-assembly Side | *b | Timing Chain Cover Side |
|
Clean and degrease | - | - |
Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the timing chain cover sub-assembly, cylinder head sub-assembly and cylinder block sub-assembly.
Be sure to clean and degrease the contact surfaces, especially the surfaces indicated in the illustration.
| *a | Seal Diameter | *b | Seal Packing |
Apply a light coat of engine oil to a new oil pump gasket.
Install the oil pump gasket.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
| *a | 3.0 to 4.0 mm (0.118 to 0.157 in.) | *b | 2.0 to 3.0 mm (0.079 to 0.118 in.) |
| *c | 155 mm (6.10 in.) | *d | 40 mm (1.57 in.) |
| *e | 30 mm (1.18 in.) | *f | 20 mm (0.787 in.) |
| *g | 5.0 to 6.0 mm (0.197 to 0.236 in.) | *h | Be sure to apply seal packing |
| *i | Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) | *j | Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent) |
| *k | Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) | *l | Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) |
Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the following illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
| Area | Seal Packing Diameter | Application Position from Inside Seal Line |
|---|---|---|
| Continuous Line Area | 4.5 mm (0.177 in.) or more | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Alternate Long and Short Dashed Line Area | 3.5 mm (0.138 in.) or more | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| Dashed Line Area | 3.5 mm (0.138 in.) or more | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Diagonal Line Area | 6.0 mm (0.236 in.) or more | 5.0 mm (0.197 in.) |
| *1 | Crankshaft Sub-assembly | - | - |
| *a | Drive Rotor Spline | *b | 15° |
Align the oil pump drive rotor spline and crankshaft sub-assembly as shown in the illustration. Install the drive rotor and timing chain cover sub-assembly to the crankshaft sub-assembly.
| *1 | Nut | - | - |
| *a | Area 1 | *b | Area 2 |
| *c | Area 3 | *d | Area 4 |
Install the timing chain cover sub-assembly with the 26 bolts (A, B, C and D) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| Item | Length |
|---|---|
| Bolt A | 28 mm (1.10 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 35 mm (1.38 in.) |
| Bolt D | 65 mm (2.56 in.) |
Make sure that there is no oil on the bolt threads.
Tighten the bolts in area 1.
Tighten the bolts from bottom to top as shown in the illustration.
Tighten the bolts in area 2.
Tighten the bolts and nuts in area 3.
Tighten the bolts and nuts from top to bottom as shown in the illustration.
Tighten the bolts in area 4.
Do not start the engine for at least 2 hours after installation.
Wipe off any seal packing that seeped out around the surfaces of the oil pan and head cover and make sure that there is no seal packing seeping out around the edges.
Tighten the bolts from bottom to top as shown in the illustration.
12101R 3.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
| *1 | Nut | - | - |
| *a | Seal Packing | - | - |
Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block sub-assembly, rear oil seal retainer and oil pan sub-assembly.
Install 3 new O-rings to the timing chain cover sub-assembly.
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surface.
Install the oil pan within 3 minutes after applying seal packing.
Install the oil pan sub-assembly with the 17 bolts (A, B, C, D and E) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
| Item | Length |
|---|---|
| Bolt A | 60 mm (2.36 in.) |
| Bolt B | 45 mm (1.77 in.) |
| Bolt C | 25 mm (0.984 in.) |
| Bolt D | 16 mm (0.630 in.) |
| Bolt E | 70 mm (2.76 in.) |
Do not start the engine for at least 2 hours after installation.
15104 4.INSTALL OIL STRAINER SUB-ASSEMBLY
12102A 5.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
| *1 | Seal Packing | - | - |
|
Bolt |
|
Nut |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.
Do not start the engine for at least 2 hours after the installation.
11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
| *a | Seal Packing | *b | Bolt A |
| *c | Bolt B | *d | Bolt C |
| *e | Bolt D | - | - |
Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the camshaft housing RH, timing chain cover sub-assembly and cylinder head cover sub-assembly.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 to 3.0 mm (0.0787 to 0.118 in.)
Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets.
Install a new gasket to the cylinder head cover sub-assembly.
Install new seal washers to the bolts.
Temporarily install the cylinder head cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| Bolt A | 25 mm (0.984 in.) |
| Bolt B | 35 mm (1.38 in.) |
| Bolt C | 65 mm (2.56 in.) |
| Bolt D | 60 mm (2.36 in.) |
Do not start the engine for at least 2 hours after installation.
11202 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
| *a | Seal Packing | *b | Bolt A |
| *c | Bolt B | *d | Bolt C |
| *e | Bolt D | - | - |
Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the camshaft housing, timing chain cover sub-assembly and cylinder head cover sub-assembly LH.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 to 3.0 mm (0.0787 to 0.118 in.)
Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets.
Install a new gasket to the cylinder head cover sub-assembly LH.
Install new seal washers to the bolts.
Temporarily install the cylinder head cover sub-assembly LH with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| Bolt A | 25 mm (0.984 in.) |
| Bolt B | 35 mm (1.38 in.) |
| Bolt C | 65 mm (2.56 in.) |
| Bolt D | 60 mm (2.36 in.) |
Do not start the engine for at least 2 hours after installation.
8.CONNECT FUEL PIPE SUB-ASSEMBLY
15772 9.INSTALL NO. 2 OIL PIPE
Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.
Do not touch the mesh when installing the oil control valve filter RH.
Install a new gasket and temporarily install the oil pipe (on the cylinder head sub-assembly side) with the oil check valve bolt.
Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the cylinder head cover sub-assembly side).
Tighten the oil pipe union (on the cylinder head sub-assembly side).
If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.
Tighten the oil pipe union (on the cylinder head cover sub-assembly side).
15771 10.INSTALL NO. 1 OIL PIPE
Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.
Do not touch the mesh when installing the oil control valve filter LH.
Install a new gasket and temporarily install the oil pipe (on the cylinder head LH side) with the oil check valve bolt.
Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the cylinder head cover sub-assembly LH side).
Tighten the oil pipe union (on the cylinder head LH side).
If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.
Tighten the oil pipe union (on the cylinder head cover sub-assembly LH side).
13471 11.INSTALL CRANKSHAFT PULLEY
Using SST, install the crankshaft pulley with the pulley set bolt.
15671 12.INSTALL OIL FILTER BRACKET
16620 13.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
|
Bolt A |
|
Bolt B |
Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.
| Item | Length |
|---|---|
| Bolt A | 70 mm (2.76 in.) |
| Bolt B | 33 mm (1.30 in.) |
Make sure that there is no oil on the bolt threads.
Tighten bolts 1 and 2 in numerical order.
Tighten the other bolts.
16603 15.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
| *a | DOUBLE | - | - |
Install the No. 1 idler pulley sub-assembly with the bolt.
Make sure that there is no oil on the bolt threads.
"DOUBLE" is marked on the No. 1 idler pulley sub-assembly to distinguish it from the No. 2 idler pulley sub-assembly.
16206 16.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
| *a | Upward | *b | Rearward |
Install the water by-pass pipe sub-assembly with the 3 bolts.
Connect the 2 hoses.
The direction of the hose clamp is indicated in the illustration.
11452 18.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
| *1 | O-ring | - | - |
Install a new O-ring to the engine oil level dipstick guide.
Apply a light coat of engine oil to the O-ring.
Push the engine oil level dipstick guide end into the guide hole.
Install the engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick.
22.INSTALL ENGINE ASSEMBLY