Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P24457F  AIR System Pump Stuck Off Bank 1 Actuator Stuck Off  


DESCRIPTION

Refer to P041211.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P041211

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P24457F AIR System Pump Stuck Off Bank 1 Actuator Stuck Off Secondary air pressure is below 1 kPa (0.145 psi) despite the ECM commanding the air pump assembly to turn on (2 trip detection logic).
·

Air pump assembly

·

Open in air pump assembly circuit

·

Secondary air injection system piping

·

Pressure sensor (bank 1 and bank 2)

·

Open or short in pressure sensor (bank 1 and bank 2) circuit

·

Air injection control driver

·

ECM


Comes on SAE: P2445

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:

·

The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump assembly.

·

The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump assembly.


Example:

DTC P24457F mainly indicates a malfunction in which the air pump assembly is stuck off.


CONFIRMATION DRIVING PATTERN

NOTICE:
·

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing Next.

12.

Perform the following to confirm the secondary air injection system pending DTCs: Press Exit.

13.

Enter the following menus: Powertrain / Engine / DTC.

14.

Check for pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



15.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

16.

Input the DTC: P24457F.

17.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24457F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read DTCs.


Result:
Result Proceed to
P24457F is output A
P24457F and P041811 and/or P041815 are output B
P24457F and other DTCs (except P041811 and P041815) are output C


If any DTCs other than P041811, P041815 and/or P24457F are output, troubleshoot those DTCs first.


A

2.READ FREEZE FRAME DATA (AIR PUMP FREEZE BANK 1, AIR SWITCHING VALVE FREEZE BANK 1 AND AIR SWITCHING VALVE FREEZE BANK 2)

B

GO TO AIR PUMP ASSEMBLY INSPECTION PROCEDURE

C

2.READ FREEZE FRAME DATA (AIR PUMP FREEZE BANK 1, AIR SWITCHING VALVE FREEZE BANK 1 AND AIR SWITCHING VALVE FREEZE BANK 2)
a.

Turn the ignition switch to ON.


b.

Read the values of Air Pump Freeze Bank 1, Air Switching Valve Freeze Bank 1 and Air Switching Valve Freeze Bank 2 from the freeze frame data recorded previously.


c.

Referring to the following table, proceed to the appropriate step according to the result of the data reading.

Result:
Result Proceed to
Air Pump Freeze Bank 1 Air Switching Valve Freeze Bank 1 Air Switching Valve Freeze Bank 2
OFF OFF OFF A
Except above B




A

8.PERFORM SECONDARY AIR INJECTION CHECK

B

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)
a.

Disconnect the air pump connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) inthe table below.

Powertrain > Engine > Active Test
Tester Display
Activate the Air Pump Heater
50004 372 92
Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C93)Location & Routing

Click Connector(C93)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Pump Assembly

C93-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

NG

5.INSPECT RELAY (AIR PMP HTR)
4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)
a.

Inspect the air pump heater resistance.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR PUMP>INSPECTION

Result:
Proceed to
OK
NG




OK

5.INSPECT RELAY (AIR PMP HTR)

NG

5.INSPECT RELAY (AIR PMP HTR)
a.

Inspect the relay (AIR PMP HTR).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

6.CHECK TERMINAL VOLTAGE (AIR PMP HTR RELAY POWER SOURCE CIRCUIT)

NG

REPLACE RELAY (AIR PMP HTR)

6.CHECK TERMINAL VOLTAGE (AIR PMP HTR RELAY POWER SOURCE CIRCUIT)
a.
A488680C02
0.104,0.104 0.417,0.26 0.313,0.156 10 false *1 0.896,1.854 1.208,2.01 0.313,0.156 10 false *a
*1 Engine Room Relay Block No. 2
*a AIR PMP HTR Relay Terminal


Remove the relay (AIR PMP HTR).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (AIR PMP HTR relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (AIR PUMP - RELAY (AIR PMP HTR), BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR PUMP - RELAY (AIR PMP HTR), BODY GROUND)
a.

Remove the relay (AIR PMP HTR).


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C93)Location & Routing

Click Connector(C93)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Pump Assembly

3 (AIR PMP HTR relay) - C93-1 (APH+) Always Below 1 Ω
C93-3 (APHG) - Body ground Always Below 1 Ω
3 (AIR PMP HTR relay) or C93-1 (APH+) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.PERFORM SECONDARY AIR INJECTION CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM SECONDARY AIR INJECTION CHECK
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Perform the secondary air injection system forced operation while the engine is idling.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 5 seconds. After the initialization, air pump assembly and emission control valve operation can be selected.


Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26

e.

Start the engine.


f.

Check that the air pump assembly (AIR PUMP), emission control valve (ASV 1 and ASV 2) and pressure in the secondary air injection system passage (PRESSURE) status displayed on the GTS match the conditions shown in the table below.

Standard:
GTS Operation AIR PUMP ASV 1
ASV 2
PRESSURE*
AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN ON ON 1 kPa or more [A]
AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE OFF OFF Less than 640 kPa [B]


*: Average pumping pressure. The pressure should be 1 kPa or more when the secondary air injection system operates.

Standard:

The pressures for [A] and [B] should differ by 1 kPa or more.



g.

Turn the ignition switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

9.CLEAR DTC

NG

11.CHECK EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
9.CLEAR DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Perform the Secondary Air Injection Check (Automatic Mode).

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26

e.

Start the engine after the GTS initialization is finished.


f.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


g.

Check pending DTCs.


h.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Result Proceed to
P24457F is output A
No pending DTC B



A

11.CHECK EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

B

11.CHECK EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Turn the ignition switch to ON.


b.

Check the pressure displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Air Pump Pressure (Absolute) Bank 1
Air Pump Pressure (Absolute) Bank 2
50003 372 1019,1020
Standard pressure:

45.6 to 135 kPa (6.612 to 19.575 psi)


HINT:

The GTS displays the air pump pressure as absolute pressure.



Result:
Proceed to
OK
NG



OK

12.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

NG

12.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS
A488986E01
0.104,0.094 2.396,0.344 2.292,0.25 10 false with Secondary Air Injection System

a.

Check that all the pipes and hoses between the air pump assembly and emission control valve set are securely connected.


b.

Inspect the pipes and hoses for blockages and damage.

OK:

Secondary air injection system piping has no blockages or damage.



Result:
Proceed to
OK
NG



OK

13.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING

13.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
a.

Disconnect the air injection control driver connectors.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

14.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.



Result:
Proceed to
OK
NG



OK

15.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT AIR PUMP ASSEMBLY

Result:
Proceed to
OK
NG



OK

19.PERFORM SECONDARY AIR INJECTION CHECK

NG

16.REPLACE AIR PUMP ASSEMBLY
16.REPLACE AIR PUMP ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

17.CLEAR DTC
17.CLEAR DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Perform the Secondary Air Injection Check (Automatic Mode).

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26

e.

Start the engine after the GTS initialization is finished.


f.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


g.

Check pending DTCs.


h.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Result Proceed to
P24457F is output A
No pending DTC B



A

END

B

19.PERFORM SECONDARY AIR INJECTION CHECK
19.PERFORM SECONDARY AIR INJECTION CHECK
a.

Disconnect the air injection control driver connector.


b.
A488681C01
0.635,0.417 0.948,0.615 0.313,0.198 10 false *1 2.552,0.365 2.865,0.563 0.313,0.198 10 false *2 0.823,0.885 1.135,1.083 0.313,0.198 10 false DI 0.771,1.24 1.083,1.438 0.313,0.198 10 false SIV 2.438,0.865 2.75,1.063 0.313,0.198 10 false AIDI 2.438,1.229 2.854,1.427 0.417,0.198 10 false AIRV
*1 Air Injection Control Driver
*2 ECM


Connect terminals DI and SIV of the wire harness connector for the air injection control driver.


c.

Turn the ignition switch to ON.


d.

Perform the secondary air injection system intrusive operation while the engine is idling.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 5 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



e.

Start the engine.


f.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.


g.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repeatedly as it may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-3 (SIV) - C96-1 (E) AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE 11 to 14 V


h.
A488681C02
0.813,0.875 1.125,1.073 0.313,0.198 10 false DI 0.656,0.438 0.969,0.635 0.313,0.198 10 false *1 2.542,0.344 2.854,0.542 0.313,0.198 10 false *2 2.406,0.854 2.719,1.052 0.313,0.198 10 false AIDI 0.76,1.219 1.073,1.417 0.313,0.198 10 false SIP 2.406,1.229 2.813,1.427 0.406,0.198 10 false AIRP
*1 Air Injection Control Driver
*2 ECM


Connect terminals DI and SIP of the wire harness connector for the air injection control driver.


i.

Turn the ignition switch to ON.


j.

Perform the secondary air injection system intrusive operation while the engine is idling.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 5 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



k.

Start the engine.


l.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.


m.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repeatedly as it may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C96)Location & Routing

Click Connector(C96)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air Injection Control Driver

C96-4 (SIP) - C96-1 (E) AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE 11 to 14 V


Result:
Proceed to
OK
NG



OK

20.REPLACE AIR INJECTION CONTROL DRIVER

NG

20.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR INJECTION DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTC.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P24457F)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Perform the Secondary Air Injection Check (Automatic Mode).

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 372 26

e.

Start the engine after the GTS initialization is finished.


f.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


g.

Check pending DTCs.


h.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Result Proceed to
P24457F is output A
No pending DTC B



A

END

B