A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure.
If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P009300, P029D00, P02A100, P02A500, P02A900, P02AD00 and P02B100.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P009300 | Fuel System Leak Detected - Large Leak | While the engine is running, a large fuel pressure decrease occurs between injections (non-injection periods) or during a half-stroke of the engine. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P0093 |
| P029D00 | Cylinder 1 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P029D |
| P02A100 | Cylinder 2 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P02A1 |
| P02A500 | Cylinder 3 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P02A5 |
| P02A900 | Cylinder 4 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P02A9 |
| P02AD00 | Cylinder 5 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P02AD |
| P02B100 | Cylinder 6 - Injector Leaking | When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more. (1 trip detection logic) |
·
Fuel line between fuel supply pump assembly and common rail assembly
·
Fuel line between common rail assembly and each injector assembly
·
Common rail assembly
·
Injector assembly
·
Pressure discharge valve (common rail assembly)
·
Fuel pressure sensor (built into injector assembly)
·
Crankshaft position sensor
·
Fuel filter element assembly
·
Open or short in injector assembly circuit
·
ECM |
Comes on | SAE Code: P02B1 |
| DTC No. | Data List |
|---|---|
| P009300 P029D00 P02A100 P02A500 P02A900 P02AD00 P02B100 |
·
Fuel Pressure (High)
·
Target Fuel Pressure (High)
·
i-ART Learning Status History #1 to #6
·
Injector Leaking Count #1 to #6 |
When DTC P009300, P029D00, P02A100, P02A500 P02A900, P02AD00 and P02B100 are set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).
| Engine Speed | Fuel Pressure (High) |
|---|---|
| Idling | Approximately 25000 to 50000 kPa |
| 3000 rpm (No engine load) | Approximately 36000 to 120000 kPa |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P009300 P029D00 P02A100 P02A500 P02A900 P02AD00 P02B100 |
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds. Fully depress the accelerator pedal for 5 seconds, and then release it.[*A] Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*B] Repeat procedures [*A] and [*B] 5 times. |
This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.
In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping.
The ECM adjusts the timing of when the pre-stroke control valve is closed to obtain the target internal fuel pressure.
If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, fuel supply pump assembly operation is limited. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
Soon after starting the engine, visually check for fuel leaks in the fuel line.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Before starting the engine, visually check for fuel leaks from the injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.
No fuel leaks in high-pressure areas.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| P009300 and "P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511 and/or P13E515" are output | C |
| P009300 and "P033511, P033515, P03351F, P03352A and/or P033531" are output | B |
| Except above | A |
A
B
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
C
Check if the fuel level is low.
| Result | Proceed to |
|---|---|
| The indicator (fuel warning light) is illuminated | A |
| The indicator (fuel warning light) is not illuminated | B |
A
B
Add fuel.
| Proceed to |
|---|
| NEXT |
NEXT
Using the hand pump bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Hand pump pumping speed: Max. 2 strokes/sec.
The hand pump must be pushed with a full stroke during pumping.
When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
If the hand pump resistance does not increase despite consecutively pumping 400 times or more, there may be a fuel leak between the fuel tank, fuel filter element sub-assembly and hand pump, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.
Start the engine.
If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
Use a fully-charged battery.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.
Turn the ignition switch off.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Start the engine.[*A]
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.[*B]
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.[*C]
| Tester Display |
|---|
| Test the Fuel Leak |
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.[*D]
Read Current DTCs.
When no DTCs are output, the air bleeding is completed.
If any DTCs are output, proceed to the next step.
Repeat steps [*A] to [*D].
Clear the DTCs.
Start the engine and warm it up.
Confirm that the shift lever is in P or N and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it.[*E]
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*F]
Repeat procedures [*E] and [*F] 5 times.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC is output | A |
| No DTC is output | B |
A
B
Read the value of Injection Feedback Value #1 to #6 in the freeze frame data recorded in Procedure 2.
| Result | Proceed to |
|---|---|
| Injection Feedback Value for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data | B |
| Except above | A |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.
A
B
Clear the DTCs.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
| Tester Display |
|---|
| Fuel Pressure (High) |
Start the engine.
Read the value of Fuel Pressure (High) while cranking and idling the engine.
| Result | Proceed to |
|---|---|
| The engine cannot be started or the engine can be started but Fuel Pressure (High) is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON | B |
| Except above | A |
A
B
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Value #1 to #6.
| Tester Display |
|---|
| Injection Feedback Value #1 |
| Injection Feedback Value #2 |
| Injection Feedback Value #3 |
| Injection Feedback Value #4 |
| Injection Feedback Value #5 |
| Injection Feedback Value #6 |
Read the values.
| GTS Display | Engine Condition* | Normal Value |
|---|---|---|
| Injection Feedback Value #1 Injection Feedback Value #2 Injection Feedback Value #3 Injection Feedback Value #4 Injection Feedback Value #5 Injection Feedback Value #6 |
Idling | -4.9 mm3/st to 4.9 mm3/st |
*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.
| Result | Proceed to |
|---|---|
| Injection Feedback Value for at least one cylinder is more than 5 mm3/st and engine vibration is abnormally large | B |
| Except above | A |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.
The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -4.9 mm3/st (-4.9 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 4.9 mm3/st or less, the injector assemblies are not malfunctioning.
A
B
Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.
Stop the vehicle and allow the engine to idle.
While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1
Repeat procedure *1 5 times.
| Result | Proceed to |
|---|---|
| No problems such as sluggishness or variations in the tachometer reading | A |
| Except above | B |
A
B
Read the value of Injector Leaking Count #1 to #6, and i-ART Learning Status History #1 to #6 in the freeze frame data recorded in Procedure 2.
If Injector Leaking Count #1 to #6 displays a value of 1 or higher, or i-ART Learning Status History #1 to #6 displays 1 or more, the injector assembly for that cylinder needs to be replaced.
In order to prevent foreign matter from entering the fuel lines, do not replace the injectors at this time. Replace the injectors after performing step 16.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the fuel filter case and replace the fuel filter element assembly.
Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Pressure (High) and Target Fuel Pressure (High).
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.
"Fuel Pressure (High)" is the actual fuel pressure.
| Result | Proceed to |
|---|---|
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa | A |
| Except above | B |
A
B
Use this Active Test to determine the malfunctioning cylinder.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Remove the glow plug for all the cylinders.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>GLOW PLUG>REMOVAL
Visually check if there is fuel on the glow plugs.
If there is fuel on a glow plug, fuel may be leaking from an injector assembly.
After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPag (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.
If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
Install the glow plug.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>GLOW PLUG>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly of the cylinder which displays a value of 4.9 mm3/st or higher for Injection Feedback Value #1 to #6 in step 8.
Replace the injector assembly determined to be the problem in step 10 and any other injector assemblies which were determined to be malfunctioning in the steps up until this point.
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the value while cranking and idling the engine.
| GTS Display | Engine Condition | Specified Condition |
|---|---|---|
| Engine Speed | Cranking | 50 to 400 rpm |
| Idling with warm engine (L4 detection switch not in L4) |
550 to 650 rpm |
The value should be the same as the actual engine speed and displayed with no interruption on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
| Tester Display |
|---|
| Fuel Pressure (High) |
Start the engine.
When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.
| *1 | Engine | *2 | Engine Wire |
| *3 | Wire to Wire | *4 | ECM |
| *a | Vibration Method (Reference) | - | - |
Clear the detected DTCs.
The "Fuel Pressure (High)" value does not change as a result of vibrations and MIL does not illuminate
| Result | Proceed to |
|---|---|
| When the wire harness is vibrated, MIL illuminates or the "Fuel Pressure (High)"value on the Data List changes due to vibration | B |
| Except above | A |
A
B
Check for intermittent problems.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Start the engine.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it.[*A]
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*B]
Repeat procedures [*A] and [*B] 5 times.
Read the DTCs.
No DTCs are output.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
| Tester Display |
|---|
| Target Fuel Pressure (High) |
Start the engine.
When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.
| *1 | Engine | *2 | Engine Wire |
| *3 | Wire to Wire | *4 | ECM |
| *a | Vibration Method (Reference) | - | - |
Clear the detected DTCs.
The "Fuel Pressure (High)" value does not change as a result of vibrations and MIL does not illuminate
| Result | Proceed to |
|---|---|
| When the wire harness is vibrated, MIL illuminates or the "Fuel Pressure (High)"value on the Data List changes due to vibration | A |
| Except above | B |
A
B
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL
Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT