The stop light switch is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P070312 | Brake Switch "B" Circuit Short to Battery | Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times. (2 trip detection logic) |
·
Short in stop light switch signal circuit
·
Stop light switch assembly
·
ECM |
Comes on | SAE Code: P0724 |
| DTC No. | Data List |
|---|---|
| P070312 | Stop Light SW |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P070312 | Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times. |
Refer to DTC P05042B.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P05042B
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.
| Tester Display |
|---|
| Stop Light SW |
Read the value displayed on the GTS when the brake pedal is depressed and released.
| Brake Pedal | Display |
|---|---|
| Released | OFF |
| Depressed | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STEP LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Brake Pedal Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B70)Location & Routingewd_type=routing;type=c;code=B70 |
||
| B70-22 (STP) - Body ground | Released | 0 to 1.5 V |
| Depressed | 7.5 to 14 V | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P070312.
Check that STATUS is NORMAL.
If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.
If STATUS is INCOMPLETE, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT