Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P042000  Catalyst System Efficiency Below Threshold (Bank 1)  P244A00  Particulate Filter Differential Pressure Too Low Bank 1  P244B00  Particulate Filter Differential Pressure Too High Bank 1  P245800  Particulate Filter Regeneration Duration Bank 1  P246300  Particulate Filter Restriction - Soot Accumulation Bank 1  


DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low catalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A490880C02
1.667,2.156 2.604,1.729 true 1.938,2.792 2.635,2.844 2.635,2.844 1.948,3.073 true 1.458,5.979 1.688,6.333 false 6.5,5.438 6.385,5.771 true 5.76,5.979 5.979,6.156 true 3.656,5.427 2.823,5.771 2.823,5.771 4.781,5.625 true 2.344,0.521 2.656,0.677 0.313,0.156 10 false *1 1.573,1.448 1.885,1.604 0.313,0.156 10 false *2 1.49,2.094 1.802,2.25 0.313,0.156 10 false *3 1.49,2.729 1.99,2.969 0.5,0.24 10 false *4 (*A) 2.927,1.135 3.24,1.292 0.313,0.156 10 false *6 3,1.979 3.313,2.135 0.313,0.156 10 false *7 3.458,3.031 3.771,3.188 0.313,0.156 10 false *8 2.99,3.313 3.302,3.469 0.313,0.156 10 false *9 6.333,2.135 6.646,2.292 0.313,0.156 10 false *10 0.281,0.313 0.75,0.469 0.469,0.156 10 false *a 1.49,2.979 1.938,3.188 0.448,0.208 10 false *5 (*B) 0.885,6.354 3.354,6.75 2.469,0.396 10 false DPF (Diesel Particulate Filter) Catalyst 5.198,6.406 6.229,6.76 1.031,0.354 10 false Magnified View 6.188,5.802 6.854,6.24 0.667,0.438 10 false Gas Flow 3.802,5.781 4.792,6.271 0.99,0.49 10 false Cross Section 2.26,5.802 3.552,6.25 1.292,0.448 10 false Alternating Blocked Passages 6.073,6.083 6.385,6.281 0.313,0.198 10 false PM 0.385,4.219 2.281,4.688 1.896,0.469 10 false DPF (Diesel Particulate Filter): 3.49,4.219 5,4.531 1.51,0.313 10 false Monolithic Construction: 5.635,4.24 6.719,4.635 1.083,0.396 10 false Wall-Flow Type: 2.375,4.635 3.344,4.813 0.969,0.177 10 false PM, HC, CO 4.833,4.531 6.063,4.729 1.229,0.198 10 false CO2, H2O
*A w/ Urea SCR System *B w/o Urea SCR System
*a Exhaust Gas - -
*1 Exhaust Fuel Addition Injector *2 Turbocharger Sub-assembly
*3 DOC Catalytic Converter *4 SCR-DPF Catalytic Converter
*5 DPF Catalytic Converter *6 Exhaust Gas Temperature Sensor
*7 No. 2 Exhaust Gas Temperature Sensor *8 Differential Pressure Sensor
*9 No. 3 Exhaust Gas Temperature Sensor *10 ECM


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P042000 Catalyst System Efficiency Below Threshold (Bank 1) During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly (DOC catalyst)

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P0420
P244A00 Particulate Filter Differential Pressure Too Low Bank 1 When driving, the catalyst differential pressure is continuously below the threshold for 7 seconds or more.
(2 trip detection logic)
·

Front exhaust pipe sub-assembly (DPF catalyst)

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P244A
P244B00 Particulate Filter Differential Pressure Too High Bank 1 While driving, Catalyst Differential Pressure becomes more than 0.32 for 3 seconds
(1 trip detection logic)
·

Front exhaust pipe sub-assembly (DPF catalyst)

·

Differential pressure sensor


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P244B
P245800 Particulate Filter Regeneration Duration Bank 1 When PM forced regeneration is manually performed, PM forced regeneration does not finish even after 60 minutes or more elapse.
(1 trip detection logic)
·

Front exhaust pipe sub-assembly (DPF catalyst)

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P2458
P246300 Particulate Filter Restriction - Soot Accumulation Bank 1 While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic)
·

Front exhaust pipe sub-assembly (DPF catalyst)

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P2463

HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P042000
P244A00
P244B00
P245800
P246300
·

Exhaust Fuel Addition F/B Bank 1

·

Catalyst Differential Pressure Bank 1

·

Particulate Filter Differential Pressure Bank 1



MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the front exhaust pipe sub-assembly.

Abnormal DOC catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.

A208470E10
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.052,0.417 1.969,0.333 10 false Catalyst Activation Malfunction: (DPF No Activate) 0.896,0.938 2.76,1.302 1.865,0.365 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.115,1.781 2.781,1.958 1.667,0.177 10 false Exhaust Gas Temperature 3.521,1.958 4.938,2.198 1.417,0.24 10 false About 300°C (572°F) 5.458,1.563 6.104,1.729 0.646,0.167 10 false Abnormal 4.49,1.208 4.969,1.375 0.479,0.167 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.063,1.146 1.5,0.344 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time


Catalytic converter differential pressure too low:

The ECM monitors the DPF catalyst differential pressure when driving and illuminates the MIL when the difference in pressure before and after the catalyst is below the threshold.


Catalytic converter differential pressure too high:

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057E22
5.979,2.354 5.802,2.354 5.802,2.354 5.573,2.146 true 2.135,3.344 2.375,3.344 2.375,3.344 2.688,2.063 true 4,1.177 4.49,0.458 4.49,0.458 4.708,0.458 true 1.094,3.271 2.188,3.677 1.094,0.406 10 false Stores P244B00 3.531,2.906 4.688,3.198 1.156,0.292 10 false Mass Air Flow 0.135,0.094 2.292,0.323 2.156,0.229 10 false Differential Pressure Malfunction: 0.167,1.635 1.448,2.542 1.281,0.906 10 false Particulate Filter Differential Pressure Bank 1 4.771,0.375 5.969,0.604 1.198,0.229 10 false Clogged with PM 5.76,1.031 7.146,1.458 1.385,0.427 10 false Increases PM amount of DPF catalyst 6.042,2.271 6.969,2.646 0.927,0.375 10 false No PM in DPF catalyst 1.125,0.729 1.51,0.958 0.385,0.229 10 false High 5.604,2.896 5.99,3.125 0.385,0.229 10 false High 1.125,2.563 1.51,2.792 0.385,0.229 10 false Low 1.573,2.906 1.958,3.135 0.385,0.229 10 false Low


Catalytic converter regeneration duration:

When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.


Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio Bank 1 and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P042000
P244A00
P245800
P246300
PM forced regeneration
P244B00 Engine is running at 4000 rpm with no load for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

After replacing the front exhaust pipe sub-assembly (DPF catalyst), the replaced, the catalyst deterioration learning value and DPF deposition value stored in the ECM must be cleared.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

If DTC P245800 or P246300 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI MAIN NO. 1 fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Record the stored DTC and freeze frame data.


c.

Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition F/B Bank 1 value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the Catalyst Differential Pressure Bank 1 value is more than 0.32, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000, P244A00, P244B00, P245800 AND P246300)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000, P244A00, P244B00, P245800 AND P246300)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P244A00 is output A
DTC P244B00 is output B
DTC P244B00 is output at the same time as P246300
DTC P042000, P245800 or P246300 is output C
Other relevant DTCs are output D




A

3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

C

11.CHECK FOR BLACK SMOKE

D

10.GO TO DTC CHART

B

22.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
3.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.


A490881C03
4.125,0.333 5.896,0.896 5.896,0.896 6.115,0.896 true 3.979,0.604 1.802,1.333 1.802,1.333 4.135,0.74 true 3.865,1.396 5.021,2.479 5.021,2.479 3.646,1.365 true 6.188,0.844 6.5,1 0.313,0.156 10 false *1 1.635,1.302 1.948,1.458 0.313,0.156 10 false *2 5.073,2.458 5.385,2.615 0.313,0.156 10 false *3
*1 Differential Pressure Sensor *2 Air Hose
*3 Vacuum Pipe - -


a.
A490882C02
2.927,1.135 0.563,1.01 0.563,1.01 2.125,0.885 true 0.333,0.948 0.625,1.135 0.292,0.188 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

NG

9.REPAIR OR REPLACE MALFUNCTIONING PARTS
4.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Turn the ignition switch to ON (engine stopped).


b.

Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Check that the differential pressure is as specified below.

OK:

Approximately 0 kPa



Result:
Proceed to
OK
NG



OK

5.CONNECT UPSTREAM AIR HOSE

NG

6.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.CONNECT UPSTREAM AIR HOSE
a.
A490883C01
2.51,0.927 0.5,1.406 0.5,1.406 0.406,1.417 true 0.167,1.365 0.479,1.563 0.313,0.198 10 false *1
*1 Air Hose (Upstream)


Connect the upstream air hose to the differential pressure sensor.


b.

Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Start the engine.


d.

Run the engine at 4000 rpm with no load for 10 seconds or more.


e.

Check that the differential pressure is as specified below.

Result:
Particulate Filter Differential Pressure Bank 1 Proceed to
1.5 kPa or higher A
Below 1.5 kPa B




B

6.REPLACE DIFFERENTIAL PRESSURE SENSOR

A

7.CONNECT DOWNSTREAM AIR HOSE
6.REPLACE DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

7.CONNECT DOWNSTREAM AIR HOSE
7.CONNECT DOWNSTREAM AIR HOSE
a.

Connect the downstream air hose to the differential pressure sensor.

A490881C04
1.938,0.938 2.031,0.938 2.031,0.938 3.979,0.573 true 1.74,0.885 2.052,1.042 0.313,0.156 10 false *1
*1 Air Hose (Downstream) - -



b.

Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Start the engine.


d.

Run the engine at 4000 rpm with no load for 10 seconds or more.


e.

Check that the differential pressure is as specified below.

Result:
Particulate Filter Differential Pressure Bank 1 Proceed to
-1.5 to 1.5 kPa A
Higher than 1.5 kPa B




A

8.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)

B

11.CHECK FOR BLACK SMOKE
8.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)
a.

It has been determined that the front exhaust pipe sub-assembly (DPF catalyst) needs to be replaced. However, perform all the troubleshooting procedures before replacing the front exhaust pipe sub-assembly (DPF catalyst).

HINT:

If the differential pressure before and after the DPF is low, it is very likely that there is no DPF or the material inside the DPF is missing due to erosion, etc. If the DPF catalyst is eroded, do not replace the DPF at this time, as troubleshooting the cause and other repairs are necessary.



Result:
Proceed to
NEXT



NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
9.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning parts.


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
10.GO TO DTC CHART
a.

Diagnose relevant DTCs.


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR BLACK SMOKE
11.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

12.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)

OK

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
12.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)
a.

It has been determined that the front exhaust pipe sub-assembly (DPF catalyst) needs to be replaced. However, perform all the troubleshooting procedures before replacing the front exhaust pipe sub-assembly (DPF catalyst).

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
13.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Remove the EFI MAIN NO. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI MAIN NO. 1 fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Turn the ignition switch to ON.


c.

Turn the ignition switch off and wait for 30 seconds or more.


d.

Turn the ignition switch to ON and wait for 10 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.




g.

Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode.

Powertrain > Engine > Utility
Tester Display
PM Regenerate Mode
50005 372 4576

h.

Enter PM Regenerate Mode.

CAUTION:

Be careful of the exhaust pipes and surrounding areas, as they become extremely hot when performing PM forced regeneration.



i.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2 and DPNR/DPF Status Regeneration (PM).

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
DPNR/DPF Status Regeneration (PM)
50003 372 1134,1086

j.

Check for temperature increases and abnormal white smoke during PM forced regeneration.

HINT:
·

PM forced regeneration takes 15 to 40 minutes to finish.

·

The time it takes to complete PM forced regeneration changes depending on "PM Accumulation Ratio Bank 1" and the vehicle operating conditions.

·

If the value of "Catalyst Differential Pressure Bank 1" increases too much during the PM forced regeneration, the fail-safe function activates and PM forced regeneration is stopped.

·

Perform PM forced regeneration control until the display on the multi-information display turns off.

·

If actions such as depressing the accelerator pedal or clutch pedal or operating the DPF switch, etc. are performed during PM forced regeneration, PM forced regeneration stops. If PM forced regeneration stops, it is necessary to perform it again.

·

PM forced regeneration control is not complete until the display on the multi-information display turns off.



Result:
Result Proceed to
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and no white smoke is generated A
During PM forced regeneration, temperature of Exhaust Temperature B1S2 is 300 to 500°C and abnormal white smoke is generated*1 B
Other than above*2 C


HINT:
·

*1: If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DOC catalyst.

·

*1: When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.

·

*2: An excess of accumulated PM is the result of a malfunction in the control system causing poor combustion and an increase in black smoke.





A

14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DOC CATALYST)

C

16.CHECK FUEL INJECTION SYSTEM
14.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

It has been determined that the exhaust fuel addition injector assembly needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust fuel addition injector assembly.


Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM
15.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DOC CATALYST)
a.

It has been determined that the exhaust manifold converter subassembly (DOC catalyst) needs to be replaced. However, perform all the troubleshooting procedures before replacing the exhaust manifold converter subassembly (DOC catalyst).

HINT:

If abnormal white smoke is only generated during PM forced regeneration, there may be uncombusted fuel due to deterioration of the DOC catalyst. When there is a malfunction with combustion control, operation performance may be reduced and abnormalities may be felt even if PM forced regeneration is performed.



Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM
16.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

17.CHECK INTAKE/EXHAUST SYSTEM
17.CHECK INTAKE/EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

18.CHECK AFTER TREATMENT CONTROL SYSTEM
18.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

19.REPAIR OR REPLACE MALFUNCTIONING PARTS
19.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P042000, P244A00, P244B00, P245800 and P246300.


a.

Replace the front exhaust pipe sub-assembly (DPF catalyst).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (for Rear Side)>REMOVAL

NOTICE:

Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION



b.

Replace the exhaust manifold converter sub-assembly (DOC catalyst).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (for Front Side)>REMOVAL

HINT:

If P042000 was output, replace the exhaust manifold converter sub-assembly (DOC catalyst).



c.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


d.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system, intake/exhaust system and after treatment control system.


e.

Check for DTCs output in step 1.

Result:
Result Proceed to
DTC P244A00 is output A
DTC other than DTC P244A00 output B




A

20.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

B

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Enter the following menus: Powertrain / Engine / Data List / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

b.

Start the engine.


c.

Run the engine at 4000 rpm with no load for 10 seconds or more.


d.

Confirmation that the differential pressure is higher than 1.5 kPa.


Result:
Proceed to
NEXT



NEXT

END

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
NEXT



NEXT

END

22.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Check the Particulate Filter Differential Pressure Bank 1 values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
Particulate Filter Differential Pressure Bank 1 increases as engine speed increases from idle speed A
Except above B


A241154E10
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 false Engine Speed (rpm) 0.698,2.99 1.75,3.406 1.052,0.417 10 false Mass Air Flow Sensor (gm/sec) 0.625,4.125 1.698,4.854 1.073,0.729 10 false Particulate Filter Differential Pressure Bank 1 (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 false A 1.771,1.875 1.875,2.156 0.104,0.281 10 false 0 1.781,3.24 1.885,3.521 0.104,0.281 10 false 0 1.792,4.615 1.896,4.896 0.104,0.281 10 false 0 0.677,0.854 1.948,1.24 1.271,0.385 10 false Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 false Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 false Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

25.CHECK FOR BLACK SMOKE

B

23.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
23.CHECK BLOCKAGE OF AIR HOSE AND VACUUM PIPE (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


HINT:

Before checking the differential pressure sensor, perform a visual inspection of the differential pressure pipes and check that they are properly connected and no air is leaking from the pipes or hoses. If a malfunction is found, repair it before checking the sensor.


A490881C03
4.125,0.333 5.896,0.896 5.896,0.896 6.115,0.896 true 3.979,0.604 1.802,1.333 1.802,1.333 4.135,0.74 true 3.865,1.396 5.021,2.479 5.021,2.479 3.646,1.365 true 6.188,0.844 6.5,1 0.313,0.156 10 false *1 1.635,1.302 1.948,1.458 0.313,0.156 10 false *2 5.073,2.458 5.385,2.615 0.313,0.156 10 false *3
*1 Differential Pressure Sensor *2 Air Hose
*3 Vacuum Pipe - -


a.
A490882C02
2.927,1.135 0.563,1.01 0.563,1.01 2.125,0.885 true 0.333,0.948 0.625,1.135 0.292,0.188 10 false *1
*1 Air Hose


Disconnect the air hoses (both upstream and downstream) from the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both air hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

24.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

27.REPAIR OR REPLACE MALFUNCTIONING PARTS
24.REPLACE DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

25.CHECK FOR BLACK SMOKE
25.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

26.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)

NG

30.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)
26.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Catalyst Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Catalyst Differential Pressure Bank 1
50003 372 954

c.

Check the value of Catalyst Differential Pressure Bank 1 at 4000 rpm without load.

Result:
Result Proceed to
Catalyst Differential Pressure Bank 1 is more than 0.32 A
Except above B




A

30.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)

B

29.PERFORM PM FORCED REGENERATION
27.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning parts.


Result:
Proceed to
NEXT



NEXT

28.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
28.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138

c.

Check the Particulate Filter Differential Pressure Bank 1 values from idle speed to unloaded maximum engine speed.

A241154E10
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 false Engine Speed (rpm) 0.698,2.99 1.75,3.406 1.052,0.417 10 false Mass Air Flow Sensor (gm/sec) 0.625,4.125 1.698,4.854 1.073,0.729 10 false Particulate Filter Differential Pressure Bank 1 (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 false A 1.771,1.875 1.875,2.156 0.104,0.281 10 false 0 1.781,3.24 1.885,3.521 0.104,0.281 10 false 0 1.792,4.615 1.896,4.896 0.104,0.281 10 false 0 0.677,0.854 1.948,1.24 1.271,0.385 10 false Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 false Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 false Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.


OK:

Particulate Filter Differential Pressure Bank 1 increases as engine speed increases from idle speed.



Result:
Proceed to
OK
NG



NG

24.REPLACE DIFFERENTIAL PRESSURE SENSOR

OK

25.CHECK FOR BLACK SMOKE
29.PERFORM PM FORCED REGENERATION
a.

Remove the EFI MAIN NO. 1 fuse or disconnect the cable from the battery terminal for 60 seconds or more, and then reinstall the EFI MAIN NO. 1 fuse or reconnect the cable to the battery terminal.

HINT:
·

The amount of built up particulate matter recorded by the ECM cannot be initialized by the GTS.

·

If the amount of built up particulate matter recorded by the ECM is not initialized, PM forced regeneration cannot be performed using the GTS.




b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

16.CHECK FUEL INJECTION SYSTEM
30.REPLACE FRONT EXHAUST PIPE SUB-ASSEMBLY (DPF CATALYST)
a.

Even though it has been determined that the front exhaust pipe sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B00 before replacing it.


Result:
Proceed to
NEXT



NEXT

16.CHECK FUEL INJECTION SYSTEM