When the absorber control ECU has not acquired the vehicle identification information, DTC C1789 is stored. When the vehicle identification information is correctly acquired, this DTC is cleared. Vehicle identification information is automatically acquired when the system enters test mode.
If an incorrect ECM is installed, the vehicle information will not match and DTC C1789 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| C1789 | Vehicle Identification Malfunction | One of the following conditions is met:
·
The vehicle identification information is not stored.
·
Vehicle identification information that is different from the stored information is received 3 times.
·
The stop and start system setting availability stored value is not stored.
·
When stored stop and start system setting is OFF, setting is determined to be ON. |
·
Vehicle identification information
·
ECM
·
CAN communication system
·
Absorber control ECU |
Does not come on | Yes (Under some of the detection conditions (control map non-retrieval or stop and start system setting availability stored value is not stored), DTC is not stored.) |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | Ignition switch is ON | ○ | ○ | ○ | ○ |
| Malfunction Status | The vehicle identification information is not stored | ○ | - | - | - |
| Vehicle identification information that is different from the stored information is received 3 times | - | ○ | - | - | |
| The stop and start system setting availability stored value is not stored | - | - | ○ | - | |
| When stored stop and start system setting is OFF, setting is determined to be ON | - | - | - | ○ | |
| Detection Time | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
Before performing troubleshooting, inspect the connectors of related circuits.
If DTC C1782 (Power Source Voltage Malfunction) is output at the same time, perform troubleshooting for C1782 first.
Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>C1782
Before replacing the absorber control ECU, perform all of the following:
Symptom simulation.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC inspection.
GTS inspection.
Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>DATA LIST / ACTIVE TEST
If no malfunctions are found in other areas, replace the absorber control ECU.
After replacing the absorber control ECU with a new one, perform registration of vehicle identification information.
Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TEST MODE PROCEDURE
Check for DTCs.
If DTC C1781 (Suspension Control ECU Malfunction) is output at the same time, perform troubleshooting for C1781 first.
| Result | Proceed to |
|---|---|
| C1781 and CAN communication malfunction DTC are not output | A |
| C1781 is output | B |
| CAN communication DTC is output | C |
A
B
C
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that vehicle identification information has been stored.
Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TEST MODE PROCEDURE
| Result | Proceed to |
|---|---|
| Information stored | A |
| Information not stored | B |
A
B
Read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop and Start Learning Status | Learning status of stop and start setting availability after vehicle identification information registration is performed | Unset, OFF or ON | OFF: w/o Stop and start system ON: w/ Stop and start system |
When "Unset", DTC C1789 is output. |
| Tester Display |
|---|
| Stop and Start Learning Status |
The display is as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the DTC was output as a result of the replacement of a related part, replace the part with one that has a correct part number.
| Related Part | ECM |
When removing a related part to check it, be sure to follow the appropriate procedures and precautions.
Refer to the following procedures to remove the ECM.
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
If parts have not been replaced and DTC C1789 is output, there may be an internal malfunction in the absorber control ECU. Therefore, replace the absorber control ECU.
| Result | Proceed to |
|---|---|
| The related part has an incorrect part number. | A |
| The related part has the correct part number, or a related part and absorber control ECU have not been replaced. | B |
A
for V35A-FTS: Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
B