| Symptom | Trouble Area |
|---|---|
|
*1: w/ Automatic Transmission System (for AJA0F) *2: w/ Stop and Start System |
|
| There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen. |
·
CAN main bus lines or connector
·
Central gateway ECU (network gateway ECU)
·
TCM*1
·
ECM
·
Engine stop and start ECU*2
·
No. 7 global CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-26 (CA4H) - I42-25 (CA4L) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-26 (CA4H) - I42-25 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-26 (CA4H) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-25 (CA4L) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-26 (CA4H) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-25 (CA4L) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I118 No. 7 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-7 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-18 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS, F33A-FTV | A |
| except V35A-FTS, F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS | A |
| except V35A-FTS | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for 1GR-FE | A |
| except 1GR-FE | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for F33A-FTV | A |
| except F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-9 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-20 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-7 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-18 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C36 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-10 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-21 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B70 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-19 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I57 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-9 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I118-20 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I118 No. 7 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-7 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-18 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS, F33A-FTV | A |
| except V35A-FTS, F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS | A |
| except V35A-FTS | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for 1GR-FE | A |
| except 1GR-FE | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for F33A-FTV | A |
| except F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-9 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-20 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-7 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-18 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C36 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-10 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-)battery terminal | 6 kΩ or higher |
| I118-21 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B70 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-8 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-19 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I57 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118,I76)Location & Routingewd_type=routing;type=c,c;code=I118,I76 |
||
| I118-9 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I118-20 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I118 No. 7 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-7 (CANH) - I118-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS, F33A-FTV | A |
| except V35A-FTS, F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-10 (CANH) - I118-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS | A |
| except V35A-FTS | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for 1GR-FE | A |
| except 1GR-FE | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for F33A-FTV | A |
| except F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-9 (CANH) - I118-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-7 (CANH) - I118-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C36 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-10 (CANH) - I118-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B70 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I57 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-9 (CANH) - I118-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I118 No. 7 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-7 (CANH) - I118-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for V35A-FTS | A |
| except V35A-FTS | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for 1GR-FE | A |
| except 1GR-FE | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| for F33A-FTV | A |
| except F33A-FTV | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I118)Location & Routingewd_type=routing;type=c;code=I118 |
||
| I118-8 (CANH) - I118-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I118 No. 7 global CAN junction connector.
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-26 (CA4H) - I42-25 (CA4L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I118 No. 7 global CAN junction connector.
Disconnect the B1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| B1-18 (CANH) - B1-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I118 No. 7 global CAN junction connector.
Disconnect the B2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B2)Location & Routingewd_type=routing;type=c;code=B2 |
||
| B2-11 (CANH) - B2-19 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I118 No. 7 global CAN junction connector.
Disconnect the B70 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B70)Location & Routingewd_type=routing;type=c;code=B70 |
||
| B70-7 (CANH) - B70-8 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG