1. BLEED AIR FROM SUSPENSION FLUID
Be sure to check the pipe connections and whether or not any hydraulic circuit parts are damaged before performing work as the hydraulic circuits become highly pressurized during air bleeding.
The pipes become highly pressurized when bleeding air. If a fluid leak is discovered, immediately release the pressure and repair the fluid leak as there is danger involved.
When bleeding air, approximately 1 liters of new fluid is needed.
Remove the No. 1 engine under cover assembly.
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>REMOVAL
Remove the No. 2 engine under cover assembly.
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
Check the pipe connections and whether or not any hydraulic circuit parts are damaged.
| *1 | Stabilizer Control Valve Sub-assembly | *2 | Front Stabilizer Control Cylinder |
| *3 | Front Stabilizer Control Cylinder LH | *4 | Rear Stabilizer Control Cylinder |
| *5 | Bleeder Plug | *6 | Upper Shutter Valve |
| *7 | Lower Shutter Valve | *8 | Inlet Port |
| *9 | Upper Chamber Bleeder Plug | *10 | Lower Chamber Bleeder Plug |
Operate the front normal close solenoid valve in the front stabilizer housing sub-assembly.
Click hereSuspension>SUSPENSION CONTROL>ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM>UTILITY
Using an 8 mm socket wrench, loosen the 2 shutter valves of the stabilizer control valve sub-assembly 1.5 to 2.5 turns.
| *1 | Upper Shutter Valve | *2 | Lower Shutter Valve |
| *3 | Inlet Port | - | - |
| *a | 1.5 to 2.5 Turns | - | - |
When loosening a shutter valve, loosen it 1.5 to 2.5 turns, but do not loosen it any more than that.
As air may enter the system or fluid may spray out, do not remove the shutter valves.
Add new fluid to SST (high pressure oil pump) and bleed air from SST hoses.
Suspension fluid AHC
If air is not bled from the hoses, the air will mix into the hydraulic circuit.
Remove the service valve cap. Then put fluid into SST (high pressure oil pump) and connect SST to the inlet port of the stabilizer control valve sub-assembly.
Using SST (high pressure oil pump), add fluid.
If a fluid leak is discovered, immediately release the pressure and repair the fluid leak as there is danger involved due to the high pressure.
Do not allow the pressure to reach 8 MPa (81.6 kgf/cm2, 1160 psi) or higher as the accumulator may be damaged.
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).*1
Check for fluid leaks from the pipe connections and hydraulic circuit parts.
Add fluid to the stabilizer control valve sub-assembly.*2
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the bleeder plug of the stabilizer control valve sub-assembly.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the bleeder plug of the stabilizer control valve sub-assembly.
for F33A-FTV:
Remove the bolt and disconnect the pressure feed tube assembly.
Add fluid to the lower chamber of the front stabilizer control cylinder LH.*3
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the lower chamber bleeder plug of the front stabilizer control cylinder LH.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the lower chamber bleeder plug of the front stabilizer control cylinder LH.
Add fluid to the upper chamber of the front stabilizer control cylinder LH.*4
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the upper chamber bleeder plug of the front stabilizer control cylinder LH.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the upper chamber bleeder plug of the front stabilizer control cylinder LH.
Add fluid to the lower chamber of the front stabilizer control cylinder.*5
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the lower chamber bleeder plug of the front stabilizer control cylinder.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the lower chamber bleeder plug of the front stabilizer control cylinder.
Add fluid to the upper chamber of the front stabilizer control cylinder.*6
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the upper chamber bleeder plug of the front stabilizer control cylinder.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the upper chamber bleeder plug of the front stabilizer control cylinder.
Add fluid to the lower chamber of the rear stabilizer control cylinder.*7
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the lower chamber bleeder plug of the rear stabilizer control cylinder.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the lower chamber bleeder plug of the rear stabilizer control cylinder.
Add fluid to the upper chamber of the rear stabilizer control cylinder.*8
Pump SST (high pressure oil pump) to add fluid until the pressure reaches 5 MPa (51.0 kgf/cm2, 725 psi).
Loosen the upper chamber bleeder plug of the rear stabilizer control cylinder.
Pump SST (high pressure oil pump) and maintain a pressure of 5 MPa (51.0 kgf/cm2, 725 psi) until air stops coming out.
Tighten the upper chamber bleeder plug of the rear stabilizer control cylinder.
Repeat procedures *1 to *8 until the air in the fluid is gone.
Using SST (high pressure oil pump), bleed the air.
Be sure to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure to all parts. If the pressure is low, the air may not be released.
Do not allow the pressure to reach 8 MPa (81.6 kgf/cm2, 1160 psi) or higher as the accumulator may be damaged.
Bleed air from the stabilizer control valve sub-assembly.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the bleeder plug of the stabilizer control valve sub-assembly to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the bleeder plug of the stabilizer control valve sub-assembly.
Bleed air from the upper chamber of the front stabilizer control cylinder LH.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the upper chamber bleeder plug of the front stabilizer control cylinder LH to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the upper chamber bleeder plug of the front stabilizer control cylinder LH.
Bleed air from the upper chamber of the front stabilizer control cylinder.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the upper chamber bleeder plug of the front stabilizer control cylinder to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the upper chamber bleeder plug of the front stabilizer control cylinder.
Bleed air from the upper chamber of the rear stabilizer control cylinder.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the upper chamber bleeder plug of the rear stabilizer control cylinder to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the upper chamber bleeder plug of the rear stabilizer control cylinder.
Apply 3 MPa (30.6 kgf/cm2, 435 psi) of pressure.
Remove the 4 bolts and disconnect the front center stabilizer brace sub-assembly.
Set the front stabilizer control cylinder LH and front stabilizer control cylinder to the maximum length.
| *1 | Front Stabilizer Control Cylinder LH | *2 | Front Stabilizer Control Cylinder |
| *a | 243.3 to 249.3 mm (9.58 to 9.81 in.) | - | - |
243.3 to 249.3 mm (9.58 to 9.81 in.)
Set the front stabilizer control cylinder LH and front stabilizer control cylinder to the maximum length to completely bleed the air.
|
Wooden Block Placement Location |
Using a transmission jack and wooden block, support the front center stabilizer brace sub-assembly.
|
Bolt (A) |
|
Bolt (B) |
Loosen the bolt (B).
Remove the 2 bolts (A) and disconnect the rear stabilizer bar sub-assembly and rear stabilizer link.
| *a | 311.3 to 317.3 mm (12.26 to 12.49 in.) |
Set the rear stabilizer control cylinder to the maximum length.
311.3 to 317.3 mm (12.26 to 12.49 in.)
Set the rear stabilizer control cylinder to the maximum length to completely bleed the air.
|
Wooden Block Placement Location |
Using a transmission jack and wooden block, support the rear stabilizer.
Bleed air from the lower chamber of the front stabilizer control cylinder LH.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the lower chamber bleeder plug of the front stabilizer control cylinder LH to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the lower chamber bleeder plug of the front stabilizer control cylinder LH.
Bleed air from the lower chamber of the front stabilizer control cylinder.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the lower chamber bleeder plug of the front stabilizer control cylinder to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the lower chamber bleeder plug of the front stabilizer control cylinder.
Bleed air from the lower chamber of the rear stabilizer control cylinder.
Pump SST (high pressure oil pump) to apply 7 MPa (71.4 kgf/cm2, 1015 psi) of pressure.
Loosen the lower chamber bleeder plug of the rear stabilizer control cylinder to bleed the air.
Tighten the bleeder plug so pressure can be applied. Repeat these steps until the air in the fluid is gone.
Tighten the lower chamber bleeder plug of the rear stabilizer control cylinder.
Apply 3 MPa (30.6 kgf/cm2, 435 psi) of pressure.
Connect the front center stabilizer brace sub-assembly with the 4 bolts.
Connect the rear stabilizer bar sub-assembly and rear stabilizer link with the 2 bolts (A).
Tighten the bolt (B).
With all wheels on the ground, apply the specified amount of pressure using SST. Maintain this pressure for 2 to 3 minutes to stabilize the pressure.
Refer to the Temperature Management Chart when Filling Fluid as the specified pressure changes according to the fluid temperature.
Perform the inspection with the vehicle load completely on the suspension.
Perform this step with the fuel tank full.
If there are any parts installed to the vehicle which place any unbalanced load on the left or right side of the vehicle, remove them.
| Condition | Specified Condition |
|---|---|
| Fluid temperature is 20°C (68°F) | 2.75 to 3.05 MPa (28.1 to 31.1 kgf/cm2, 399 to 442 psi) |
Measure vehicle height.
Tighten the 2 shutter valves of the stabilizer control valve sub-assembly.
Remove SST (high pressure oil pump) from the inlet port of the stabilizer control valve sub-assembly.
Make sure that no pressure is applied to SST (high pressure oil pump).
Install the service valve caps to the inlet port of the stabilizer control valve sub-assembly.
for F33A-FTV:
Connect the pressure feed tube assembly with the bolt.
Inspect for suspension fluid leaks.
Install the No. 2 engine under cover assembly.
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
Install the No. 1 engine under cover assembly.
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>INSTALLATION
2. TEMPERATURE MANAGEMENT CHART WHEN FILLING FLUID
| *a | 2.48 MPa (25.2 kgf/cm2, 359 psi) | *b | 2.59 MPa (26.4 kgf/cm2, 375 psi) |
| *c | 2.70 MPa (27.5 kgf/cm2, 391 psi) | *d | 2.81 MPa (28.6 kgf/cm2, 407 psi) |
| *e | 2.93 MPa (29.8 kgf/cm2, 424 psi) | *f | 3.05 MPa (31.1 kgf/cm2, 442 psi) |
| *g | 3.18 MPa (32.4 kgf/cm2, 461 psi) | *h | 3.31 MPa (33.7 kgf/cm2, 479 psi) |
| *i | 3.45 MPa (35.1 kgf/cm2, 500 psi) | *j | 3.60 MPa (36.7 kgf/cm2, 522 psi) |
| *k | 3.76 MPa (38.3 kgf/cm2, 545 psi) | *l | 2.34 MPa (23.9 kgf/cm2, 340 psi) |
| *m | 2.41 MPa (24.6 kgf/cm2, 350 psi) | *n | 2.49 MPa (25.4 kgf/cm2, 362 psi) |
| *o | 2.58 MPa (26.4 kgf/cm2, 375 psi) | *p | 2.66 MPa (27.2 kgf/cm2, 386 psi) |
| *q | 2.75 MPa (28.1 kgf/cm2, 399 psi) | *r | 2.84 MPa (29.0 kgf/cm2, 412 psi) |
| *s | 2.94 MPa (30.0 kgf/cm2, 427 psi) | *t | 3.04 MPa (31.0 kgf/cm2, 441 psi) |
| *u | 3.14 MPa (32.1 kgf/cm2, 456 psi) | *v | 3.25 MPa (33.2 kgf/cm2, 472 psi) |
| *w | Upper Side: Charged Pressure Upper Limit | *x | Lower Side: Charged Pressure Lower Limit |
| *y | Pressure(MPa (kgf/cm2, psi)) | *z | Temperature(°C (°F)) |