When the seat heater switch (front left side) is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly receives the signal and operates the front left side seat heater.
If the battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection for the charging system.
for 1GR-FE: Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for V35A-FTS: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for F33A-FTV: Click herePower Source / Network>F33A-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
w/ Power Tilt and Power Telescopic Steering Column
If the mirror heater is operated when the battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the mirror heater may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X21B6" is not stored before proceeding with troubleshooting.
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Left Seat Heater | LH side front seat heater operation | OFF/ON | - |
| Tester Display |
|---|
| Front Left Seat Heater |
LH side front seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
The seat heater operates normally.
| Result | Proceed to |
|---|---|
| Does not operate normally with operation of either the multi-display or seat blower switch | A |
| Does not operate normally with operation of the multi-display | B |
| Does not operate normally with operation of the seat blower switch | C |
A
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
B
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front Side)>REMOVAL
Disconnect the i16 seat heater control sub-assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i16)Location & Routingewd_type=routing;type=c;code=i16 Click Connector(i16)Seat>Front Seat Wire LH>Seat Heater Control Sub-Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i16;pinno=1 |
||
| i16-1 (+B1) - Body ground | Ignition switch ON | 11 to 14 V |
| i16-1 (+B1) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I31 air conditioning amplifier assembly connector.
Disconnect the i16 seat heater control sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I31,i16)Location & Routingewd_type=routing;type=c,c;code=I31,i16 Click Connector(i16)Seat>Front Seat Wire LH>Seat Heater Control Sub-Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i16;pinno=5 |
||
| I31-13 (SM1L) - i16-5 (SWR) | Always | Below 1 Ω |
| I31-13 (SM1L) or i16-5 (SWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the i5 front seat cushion heater assembly LH connector.
Disconnect the i16 seat heater control sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(i5,i16)Location & Routingewd_type=routing;type=c,c;code=i5,i16 Click Connector(i5)Seat>Front Seat Wire LH>Front Seat Cushion Heater LH (Front Seat Cushion Pad LH)ewd_type=component;type=c;code=i5;pinno=6,1,2 Click Connector(i16)Seat>Front Seat Wire LH>Seat Heater Control Sub-Assembly LH (Front Seat LH)ewd_type=component;type=c;code=i16;pinno=10,7 |
||
| i5-6 - i16-10 (E) | Always | Below 1 Ω |
| i5-6 or i16-10 (E) - Body ground | Always | 10 kΩ or higher |
| i5-1 - i16-7 (HTR1) | Always | Below 1 Ω |
| i5-1 or i16-7 (HTR1) - Body ground | Always | 10 kΩ or higher |
| i5-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Replace the seat heater control sub-assembly LH with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER CONTROL (for Front Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the LH side front seat heater operation.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK
Front left side seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG