Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P064C9E  Glow Plug Control Module 1 Stuck On  P066B19  Cylinder 1 Glow Plug Control Circuit High Circuit Current Above Threshold  P066D19  Cylinder 2 Glow Plug Control Circuit High Circuit Current Above Threshold  P066F19  Cylinder 3 Glow Plug Control Circuit High Circuit Current Above Threshold  P067116  Cylinder 1 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067216  Cylinder 2 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067316  Cylinder 3 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067416  Cylinder 4 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067516  Cylinder 5 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067616  Cylinder 6 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067B19  Cylinder 4 Glow Plug Control Circuit High Circuit Current Above Threshold  P067D19  Cylinder 5 Glow Plug Control Circuit High Circuit Current Above Threshold  P067F19  Cylinder 6 Glow Plug Control Circuit High Circuit Current Above Threshold  P06F59E  Glow Plug Control Module 2 Stuck On  P166F2B  Glow Plug Control Module 1 Signal Cross Coupled  P16712B  Glow Plug Control Module 2 Signal Cross Coupled  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P064C9E Glow Plug Control Module 1 Stuck On The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plug assemblies are on.
(2 trip detection logic)
Glow plug controller (Bank 1) Comes on SAE Code: P064C
P066B19 Cylinder 1 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 1 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 1 glow plug assembly

·

Short in No. 1 glow plug assembly circuit


Comes on SAE Code: P066B
P066D19 Cylinder 2 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 2 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 2 glow plug assembly

·

Short in No. 2 glow plug assembly circuit


Comes on SAE Code: P066D
P066F19 Cylinder 3 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 3 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 3 glow plug assembly

·

Short in No. 3 glow plug assembly circuit


Comes on SAE Code: P066F
P067116 Cylinder 1 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 1 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 1 glow plug assembly

·

Open in No. 1 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0671
P067216 Cylinder 2 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 2 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 2 glow plug assembly

·

Open in No. 2 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0672
P067316 Cylinder 3 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 3 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 3 glow plug assembly

·

Open in No. 3 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0673
P067416 Cylinder 4 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 4 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 4 glow plug assembly

·

Open in No. 4 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0674
P067516 Cylinder 5 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 5 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 5 glow plug assembly

·

Open in No. 5 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0675
P067616 Cylinder 6 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 6 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 6 glow plug assembly

·

Open in No. 6 glow plug assembly circuit

·

GLOW relay


Comes on SAE Code: P0676
P067B19 Cylinder 4 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 4 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 4 glow plug assembly

·

Short in No. 4 glow plug assembly circuit


Comes on SAE Code: P067B
P067D19 Cylinder 5 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 5 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

No. 5 glow plug assembly

·

Short in No. 5 glow plug assembly circuit


Comes on SAE Code: P067D
P067F19 Cylinder 6 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 6 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

No. 6 glow plug assembly

·

Short in No. 6 glow plug assembly circuit


Comes on SAE Code: P067F
P06F59E Glow Plug Control Module 2 Stuck On The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plug assemblies are on.
(2 trip detection logic)
Glow plug controller (Bank 2) Comes on SAE Code: P06F5
P166F2B Glow Plug Control Module 1 Signal Cross Coupled A short circuit in a wire harness between the glow plug assemblies is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 1)

·

Short in glow plug assembly circuit


Comes on SAE Code: P166F
P16712B Glow Plug Control Module 2 Signal Cross Coupled A short circuit in a wire harness between the glow plug assemblies is detected 3 times while the glow plug assemblies are on.
(2 trip detection logic)
·

Glow plug controller (Bank 2)

·

Short in glow plug assembly circuit


Comes on SAE Code: P1671

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P064C9E
P066B19
P066D19
P066F19
P067116
P067216
P067316
P067416
P067516
P067616
P067B19
P067D19
P067F19
P06F59E
P166F2B
P16712B
The engine coolant temperature is 35°C or less and the ignition switch is turned to ON.
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P067116, P067216, P067316, P067416, P067516 and/or P067616 is output A
DTC P066B19, P066D19, P066F19, P067B19, P067D19 and/or P067F19 is output B
DTC P064C9E, P06F59E, P166F2B and/or P16712B is output C




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)

B

13.CHECK HARNESS AND CONNECTOR

C

18.CHECK HARNESS AND CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)
a.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

b.

Disconnect the glow plug controller connector.


c.

Turn the ignition switch to ON.

HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR

NG

8.INSPECT GLOW NO. 1, NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A490885C01
4.417,0.146 4.875,0.448 0.458,0.302 5.927,0.125 6.385,0.427 0.458,0.302 4.417,0.51 4.875,0.813 0.458,0.302 5.938,0.51 6.396,0.813 0.458,0.302 1.969,2.615 1.854,2.615 1.854,2.615 1.615,2.396 true 2.885,2.042 2.635,2.313 2.635,2.313 2.521,2.313 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.208,1.615 2.542,1.292 2.542,1.292 2.667,1.292 true 4.875,1.458 5.104,1.917 true 4.542,1.438 4.292,1.938 true 6.042,1.458 6,1.927 true 1.281,1.896 0.833,2.313 0.833,2.313 0.688,2.313 true 0.823,1.469 0.375,1.885 0.375,1.885 0.229,1.885 true 0.271,0.427 0.583,0.625 0.313,0.198 10 false *1 0.104,1.823 0.417,2.021 0.313,0.198 10 false 5 2.271,0.854 2.583,1.052 0.313,0.198 10 false 6 2.396,2.26 2.708,2.458 0.313,0.198 10 false 2 2.031,2.531 2.344,2.729 0.313,0.198 10 false 1 4.521,0.229 4.833,0.427 0.313,0.198 10 false B73 4.521,0.594 4.896,0.823 0.375,0.229 10 false B77 5.51,0.073 5.823,0.271 0.313,0.198 10 false *b 3.844,0.063 4.156,0.26 0.313,0.198 10 false *a 4.146,1.958 4.802,2.219 0.656,0.26 10 false GL1 5.021,2.146 5.521,2.375 0.5,0.229 10 false GL5 5.896,1.979 6.208,2.177 0.313,0.198 10 false GL3 5.896,2.146 6.208,2.344 0.313,0.198 10 false GL6 1.552,0.417 1.865,0.615 0.313,0.198 10 false *2 0.552,2.25 0.865,2.448 0.313,0.198 10 false 3 6.021,0.188 6.333,0.385 0.313,0.198 10 false B72 6.031,0.604 6.406,0.833 0.375,0.229 10 false B76 4.156,2.146 4.573,2.354 0.417,0.208 10 false GL4 5.01,1.969 5.51,2.198 0.5,0.229 10 false GL2 4.167,0.24 4.479,0.438 0.313,0.198 10 false *c 4.177,0.594 4.49,0.792 0.313,0.198 10 false *d 5.719,0.229 6.031,0.427 0.313,0.198 10 false *c 5.74,0.583 6.052,0.781 0.313,0.198 10 false *d 3.896,1.927 4.208,2.125 0.313,0.198 10 false *c 4.781,1.948 5.094,2.146 0.313,0.198 10 false *c 5.698,1.958 6.01,2.156 0.313,0.198 10 false *c 3.896,2.156 4.208,2.354 0.313,0.198 10 false *d 5.688,2.146 6,2.344 0.313,0.198 10 false *d 4.781,2.146 5.094,2.344 0.313,0.198 10 false *d 2.74,1.208 3.052,1.406 0.313,0.198 10 false 4
*1 Glow Plug Connector (Bank 1) *2 Glow Plug Connector (Bank 2)
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)
*c Bank 1 *d Bank 2



b.

Remove the glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B73,B72,B77,B76)Location & Routing

Click Connector(B73)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B72)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B77)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B76)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B73-1 (GL1) - glow plug connector (bank 1) terminal 1 Always Below 1 Ω
B73-2 (GL2) - glow plug connector (bank 1) terminal 3 Always Below 1 Ω
B72-1 (GL3) - glow plug connector (bank 1) terminal 5 Always Below 1 Ω
B77-1 (GL4) - glow plug connector (bank 2) terminal 2 Always Below 1 Ω
B77-2 (GL5) - glow plug connector (bank 2) terminal 4 Always Below 1 Ω
B76-1 (GL6) - glow plug connector (bank 2) terminal 6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG ASSEMBLY
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Exchange the glow plug assemblies of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plug assemblies of normally functioning cylinders.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
Same DTCs (that have been cleared) A
Other DTCs B




A

19.REPLACE GLOW PLUG CONTROLLER

B

5.REPLACE GLOW PLUG ASSEMBLY
5.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>F33A-FTV (STARTING)>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.INSPECT GLOW NO. 1, NO. 2 RELAY
a.

Inspect the GLOW NO. 1, NO. 2 relay.

Click hereEngine / Hybrid System>F33A-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

12.REPLACE GLOW NO. 1, NO. 2 RELAY
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


d.

Remove the GLOW NO. 1 relay and GLOW NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


e.

Disconnect connectors of the glow plug controller.


f.

Disconnect the ECM connectors.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B71,B70,B75)Location & Routing

Click Connector(B71)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

Click Connector(B75)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

GLOW NO. 1 relay terminal 3 - Battery positive terminal Always Below 1 Ω
GLOW relay terminal 1 - EFI MAIN NO. 2 relay terminal 3 Always Below 1 Ω
GLOW NO. 1 relay terminal 5 - B71-1 (BATT) Always Below 1 Ω
GLOW NO. 1 relay terminal 2 - B70-44 (GREL) Always Below 1 Ω
GLOW NO. 2 relay terminal 3 - Battery positive terminal Always Below 1 Ω
GLOW NO. 2 relay terminal 1 - EFI MAIN NO. 2 relay terminal 3 Always Below 1 Ω
GLOW NO. 2 relay terminal 5 - B75-1 (BAT2) Always Below 1 Ω
GLOW NO. 2 relay terminal 2 - B70-43 (GRL2) Always Below 1 Ω
GLOW NO. 1 relay terminal 3 or Battery positive terminal - Body ground and other terminals Always 10 kΩ or higher
GLOW relay terminal 1 or EFI MAIN NO. 2 relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 1 relay terminal 5 or B71-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 1 relay terminal 2 or B70-44 (GREL) - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 2 relay terminal 3 or Battery positive terminal - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 2 relay terminal 1 or EFI MAIN NO. 2 relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 2 relay terminal 5 or B75-1 (BAT2) - Body ground and other terminals Always 10 kΩ or higher
GLOW NO. 2 relay terminal 2 or B70-43 (GRL2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE GLOW NO. 1, NO. 2 RELAY
a.

Replace the GLOW NO. 1, NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A490885C01
4.417,0.146 4.875,0.448 0.458,0.302 5.927,0.125 6.385,0.427 0.458,0.302 4.417,0.51 4.875,0.813 0.458,0.302 5.938,0.51 6.396,0.813 0.458,0.302 1.969,2.615 1.854,2.615 1.854,2.615 1.615,2.396 true 2.885,2.042 2.635,2.313 2.635,2.313 2.521,2.313 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.208,1.615 2.542,1.292 2.542,1.292 2.667,1.292 true 4.875,1.458 5.104,1.917 true 4.542,1.438 4.292,1.938 true 6.042,1.458 6,1.927 true 1.281,1.896 0.833,2.313 0.833,2.313 0.688,2.313 true 0.823,1.469 0.375,1.885 0.375,1.885 0.229,1.885 true 0.271,0.427 0.583,0.625 0.313,0.198 10 false *1 0.104,1.823 0.417,2.021 0.313,0.198 10 false 5 2.271,0.854 2.583,1.052 0.313,0.198 10 false 6 2.396,2.26 2.708,2.458 0.313,0.198 10 false 2 2.031,2.531 2.344,2.729 0.313,0.198 10 false 1 4.521,0.229 4.833,0.427 0.313,0.198 10 false B73 4.521,0.594 4.896,0.823 0.375,0.229 10 false B77 5.51,0.073 5.823,0.271 0.313,0.198 10 false *b 3.844,0.063 4.156,0.26 0.313,0.198 10 false *a 4.146,1.958 4.802,2.219 0.656,0.26 10 false GL1 5.021,2.146 5.521,2.375 0.5,0.229 10 false GL5 5.896,1.979 6.208,2.177 0.313,0.198 10 false GL3 5.896,2.146 6.208,2.344 0.313,0.198 10 false GL6 1.552,0.417 1.865,0.615 0.313,0.198 10 false *2 0.552,2.25 0.865,2.448 0.313,0.198 10 false 3 6.021,0.188 6.333,0.385 0.313,0.198 10 false B72 6.031,0.604 6.406,0.833 0.375,0.229 10 false B76 4.156,2.146 4.573,2.354 0.417,0.208 10 false GL4 5.01,1.969 5.51,2.198 0.5,0.229 10 false GL2 4.167,0.24 4.479,0.438 0.313,0.198 10 false *c 4.177,0.594 4.49,0.792 0.313,0.198 10 false *d 5.719,0.229 6.031,0.427 0.313,0.198 10 false *c 5.74,0.583 6.052,0.781 0.313,0.198 10 false *d 3.896,1.927 4.208,2.125 0.313,0.198 10 false *c 4.781,1.948 5.094,2.146 0.313,0.198 10 false *c 5.698,1.958 6.01,2.156 0.313,0.198 10 false *c 3.896,2.156 4.208,2.354 0.313,0.198 10 false *d 5.688,2.146 6,2.344 0.313,0.198 10 false *d 4.781,2.146 5.094,2.344 0.313,0.198 10 false *d 2.74,1.208 3.052,1.406 0.313,0.198 10 false 4
*1 Glow Plug Connector (Bank 1) *2 Glow Plug Connector (Bank 2)
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)
*c Bank 1 *d Bank 2



b.

Remove the glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B73,B72,B77,B76)Location & Routing

Click Connector(B73)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B72)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B77)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B76)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B73-1 (GL1) or glow plug connector (bank 1) terminal 1 - Body ground and other terminals Always 10 kΩ or higher
B73-2 (GL2) or glow plug connector (bank 1) terminal 3 - Body ground and other terminals Always 10 kΩ or higher
B72-1 (GL3) or glow plug connector (bank 1) terminal 5 - Body ground and other terminals Always 10 kΩ or higher
B77-1 (GL4) or glow plug connector (bank 2) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
B77-2 (GL5) or glow plug connector (bank 2) terminal 4 - Body ground and other terminals Always 10 kΩ or higher
B76-1 (GL6) or glow plug connector (bank 2) terminal 6 - Body ground and other terminals Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

14.REPLACE GLOW PLUG CONTROLLER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

OK:

No DTC is output.



Result:
Proceed to
OK
NG



OK

END

NG

17.REPLACE GLOW PLUG ASSEMBLY
17.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>F33A-FTV (STARTING)>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A490885C01
4.417,0.146 4.875,0.448 0.458,0.302 5.927,0.125 6.385,0.427 0.458,0.302 4.417,0.51 4.875,0.813 0.458,0.302 5.938,0.51 6.396,0.813 0.458,0.302 1.969,2.615 1.854,2.615 1.854,2.615 1.615,2.396 true 2.885,2.042 2.635,2.313 2.635,2.313 2.521,2.313 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.208,1.615 2.542,1.292 2.542,1.292 2.667,1.292 true 4.875,1.458 5.104,1.917 true 4.542,1.438 4.292,1.938 true 6.042,1.458 6,1.927 true 1.281,1.896 0.833,2.313 0.833,2.313 0.688,2.313 true 0.823,1.469 0.375,1.885 0.375,1.885 0.229,1.885 true 0.271,0.427 0.583,0.625 0.313,0.198 10 false *1 0.104,1.823 0.417,2.021 0.313,0.198 10 false 5 2.271,0.854 2.583,1.052 0.313,0.198 10 false 6 2.396,2.26 2.708,2.458 0.313,0.198 10 false 2 2.031,2.531 2.344,2.729 0.313,0.198 10 false 1 4.521,0.229 4.833,0.427 0.313,0.198 10 false B73 4.521,0.594 4.896,0.823 0.375,0.229 10 false B77 5.51,0.073 5.823,0.271 0.313,0.198 10 false *b 3.844,0.063 4.156,0.26 0.313,0.198 10 false *a 4.146,1.958 4.802,2.219 0.656,0.26 10 false GL1 5.021,2.146 5.521,2.375 0.5,0.229 10 false GL5 5.896,1.979 6.208,2.177 0.313,0.198 10 false GL3 5.896,2.146 6.208,2.344 0.313,0.198 10 false GL6 1.552,0.417 1.865,0.615 0.313,0.198 10 false *2 0.552,2.25 0.865,2.448 0.313,0.198 10 false 3 6.021,0.188 6.333,0.385 0.313,0.198 10 false B72 6.031,0.604 6.406,0.833 0.375,0.229 10 false B76 4.156,2.146 4.573,2.354 0.417,0.208 10 false GL4 5.01,1.969 5.51,2.198 0.5,0.229 10 false GL2 4.167,0.24 4.479,0.438 0.313,0.198 10 false *c 4.177,0.594 4.49,0.792 0.313,0.198 10 false *d 5.719,0.229 6.031,0.427 0.313,0.198 10 false *c 5.74,0.583 6.052,0.781 0.313,0.198 10 false *d 3.896,1.927 4.208,2.125 0.313,0.198 10 false *c 4.781,1.948 5.094,2.146 0.313,0.198 10 false *c 5.698,1.958 6.01,2.156 0.313,0.198 10 false *c 3.896,2.156 4.208,2.354 0.313,0.198 10 false *d 5.688,2.146 6,2.344 0.313,0.198 10 false *d 4.781,2.146 5.094,2.344 0.313,0.198 10 false *d 2.74,1.208 3.052,1.406 0.313,0.198 10 false 4
*1 Glow Plug Connector (Bank 1) *2 Glow Plug Connector (Bank 2)
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)
*c Bank 1 *d Bank 2



b.

Remove the glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B73,B72,B77,B76)Location & Routing

Click Connector(B73)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B72)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B77)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B76)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B73-1 (GL1) or glow plug connector (bank 1) terminal 1 - Body ground and other terminals Always 10 kΩ or higher
B73-2 (GL2) or glow plug connector (bank 1) terminal 3 - Body ground and other terminals Always 10 kΩ or higher
B72-1 (GL3) or glow plug connector (bank 1) terminal 5 - Body ground and other terminals Always 10 kΩ or higher
B77-1 (GL4) or glow plug connector (bank 2) terminal 2 - Body ground and other terminals Always 10 kΩ or higher
B77-2 (GL5) or glow plug connector (bank 2) terminal 4 - Body ground and other terminals Always 10 kΩ or higher
B76-1 (GL6) or glow plug connector (bank 2) terminal 6 - Body ground and other terminals Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

19.REPLACE GLOW PLUG CONTROLLER

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END