The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic). |
·
Open or short in park/neutral position switch assembly circuit
·
Park/Neutral position switch assembly
·
ECM
·
TCM |
Comes on | SAE Code: P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | Either of the following conditions A or B is met (2 trip detection logic): A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more: (a) Any 2 or more of the following signals are on simultaneously:
·
P input signal
·
R input signal
·
D input signal (b) Any 2 or more of the following signals are on simultaneously:
·
N input signal
·
R input signal
·
D input signal (c) Any 2 or more of the following signals are on simultaneously:
·
NSW input signal
·
R input signal
·
D input signal B. Any of the following conditions is met for 2 seconds or more with the shift lever in M:
·
NSW input signal is on
·
P input signal is on
·
N input signal is on
·
R input signal is on |
·
Open or short in park/neutral position switch assembly circuit
·
Park/Neutral position switch assembly
·
Open or short in transmission control switch circuit
·
Transmission control switch
·
ECM
·
TCM |
Comes on | SAE Code: P0705 |
| DTC No. | Data List |
|---|---|
| P070513 P070562 |
Transmission:
·
Shift SW Status (P Range)
·
Shift SW Status (R Range)
·
Shift SW Status (N Range)
·
Shift SW Status (D Range) Engine:
·
Neutral Position SW
·
Shift SW Status (S Range) |
These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or M). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P070513 P070562 |
With the ignition switch turned to ON, move the shift lever to R, N, D, M and then P for 2 seconds or more in each position. |
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Perform the Health Check using the GTS.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P070513 or P070562 is output | A |
| P070513 or P070562 and other DTCs are output | B |
If any DTCs other than P070513 or P070562 are output, troubleshoot those DTCs first.
A
B
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| GTS Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Shift SW Status (P Range) | P | ON |
| Except P | OFF | |
| Shift SW Status (R Range) | R | ON |
| Except R | OFF | |
| Shift SW Status (N Range) | N | ON |
| Except N | OFF | |
| Shift SW Status (D Range) | D or M | ON |
| Except D or M | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Neutral Position SW |
| GTS Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Neutral Position SW | P or N | ON |
| Except P or N | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List displayed on the GTS.
| Tester Display |
|---|
| Shift SW Status (S Range) |
| GTS Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Shift SW Status (S Range) | M | ON |
| Except M | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the transmission control switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I73,B70)Location & Routingewd_type=routing;type=c,c;code=I73,B70 |
||
| I73-5 (S) - B70-32 (S) | Always | Below 1 Ω |
| I73-5 (S) or B70-32 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I74,B70)Location & Routingewd_type=routing;type=c,c;code=I74,B70 |
||
| I74-5 (S) - B70-32 (S) | Always | Below 1 Ω |
| I74-5 (S) or B70-32 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34,B70)Location & Routingewd_type=routing;type=c,c;code=C34,B70 |
||
| C34-4 (B) - B70-30 (NSW) | Always | Below 1 Ω |
| C34-4 (B) or B70-30 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34)Location & Routingewd_type=routing;type=c;code=C34 |
||
| C34-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the park/neutral position switch assembly connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34,C36)Location & Routingewd_type=routing;type=c,c;code=C34,C36 |
||
| C34-7 (DL) - C36-35 (D) | Always | Below 1 Ω |
| C34-9 (NL) - C36-16 (N) | Always | Below 1 Ω |
| C34-1 (RL) - C36-34 (R) | Always | Below 1 Ω |
| C34-6 (PL) - C36-15 (P) | Always | Below 1 Ω |
| C34-7 (DL) or C36-35 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-9 (NL) or C36-16 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-1 (RL) or C36-34 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-6 (PL) or C36-15 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG