Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2022.11
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150819  Turn Signal/Hazard Flasher Circuit Current Above Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B150819 Turn Signal/Hazard Flasher Circuit Current Above Threshold
Diagnosis Condition:

Battery voltage is 10 V or more


Malfunction Status:
·

Short in front turn signal light circuit

·

Short in side turn signal light circuit

·

Short in rear turn signal light circuit


·

Headlight unit assembly (w/ Headlight ECU)

·

Headlight housing (w/o Headlight ECU)

·

Headlight lens sub-assembly

·

Headlight ECU sub-assembly (w/ Headlight ECU)

·

Side turn signal light assembly

·

Outer mirror retractor

·

Outer mirror control ECU assembly (w/ Outer Mirror Control ECU Assembly)

·

Rear combination light cord

·

Rear combination light assembly

·

Rear light socket and wire (for Sequential Type Turn Signal Light)

·

Rear light assembly (for Sequential Type Turn Signal Light)

·

Headlight cord (w/ Headlight ECU for RHD)

·

Harness or connector

·

Combination meter assembly



WIRING DIAGRAM

B604975E04
0.906,2.354 3.198,2.552 2.292,0.198 10 false Headlight Unit Assembly RH 0.448,1.885 2.74,2.083 2.292,0.198 10 false Headlight Lens Sub-assembly RH 3.417,2.563 4.708,2.969 1.292,0.406 10 false Headlight ECU Sub-assembly RH 3.323,1.083 5.615,1.281 2.292,0.198 10 false A 3.313,1.583 5.604,1.781 2.292,0.198 10 false A 3.281,1.406 5.573,1.604 2.292,0.198 10 false 20 3.333,0.906 5.625,1.104 2.292,0.198 10 false 6 4.677,1.427 6.969,1.625 2.292,0.198 10 false 12 4.677,0.906 6.969,1.104 2.292,0.198 10 false 11 4.26,1.115 6.552,1.313 2.292,0.198 10 false TNS 4.26,1.625 6.552,1.823 2.292,0.198 10 false GND 4.667,1.615 5.104,2.021 0.438,0.406 10 false B7 4.667,1.104 5.104,1.51 0.438,0.406 10 false B7 6.052,1.052 6.49,1.458 0.438,0.406 10 false LR 5.771,0.927 6.208,1.333 0.438,0.406 10 false 5 5.771,7 7.094,7.573 1.323,0.573 10 false I6 5.75,7.177 7.073,7.75 1.323,0.573 10 false Combination Meter Assembly 2.635,5.438 4.927,5.635 2.292,0.198 10 false Headlight Housing RH 4.656,4.469 5.094,4.875 0.438,0.406 10 false B6 0.094,0.135 2.604,0.406 2.51,0.271 12 false w/ Headlight ECU for LHD: 0.115,3.406 1.604,3.615 1.49,0.208 12 false w/o Headlight ECU: 4.219,4.833 4.542,5.042 0.323,0.208 10 false GND 4.427,4.354 6.719,4.552 2.292,0.198 10 false B 4.708,4.792 7,4.99 2.292,0.198 10 false 7 4.698,4.292 4.823,4.49 0.125,0.198 10 false 8 0.24,5.427 2.531,5.625 2.292,0.198 10 false Headlight Lens Sub-assembly RH 2.438,4.292 2.563,4.49 0.125,0.198 10 false 1 2.406,4.792 4.698,4.99 2.292,0.198 10 false 4 2.406,4.458 2.729,4.667 0.323,0.208 10 false B 2.396,4.958 2.719,5.167 0.323,0.208 10 false B 4.667,4.958 5.104,5.365 0.438,0.406 10 false B6

B671778E01
0.125,0.156 4.708,0.396 4.583,0.24 12 false w/ Headlight ECU for RHD: 0.344,1.885 1.604,2.271 1.26,0.385 10 false Headlight Lens Sub-assembly RH 2.042,2.854 3.292,3.219 1.25,0.365 10 false Headlight ECU Sub-assembly RH 5.927,3.833 6.24,4.031 0.313,0.198 10 false I6 5.917,3.99 7.094,4.354 1.177,0.365 10 false Combination Meter Assembly 3.51,2.417 6.115,2.615 2.604,0.198 10 false Headlight Cord RH 1.938,1.094 2.094,1.292 0.156,0.198 10 false B 1.927,1.594 2.083,1.792 0.156,0.198 10 false B 1.917,1.385 2.229,1.583 0.313,0.198 10 false 20 1.948,0.917 2.104,1.115 0.156,0.198 10 false 6 2.823,0.979 3.281,1.177 0.458,0.198 10 false TNS 2.854,1.469 3.313,1.667 0.458,0.198 10 false GND 3.25,1.094 3.708,1.292 0.458,0.198 10 false B89 3.25,1.594 3.708,1.792 0.458,0.198 10 false B89 4.625,1.094 5.083,1.292 0.458,0.198 10 false BB8 4.625,1.594 5.083,1.792 0.458,0.198 10 false BB9 4.708,1.396 4.865,1.594 0.156,0.198 10 false 1 4.719,0.875 4.875,1.073 0.156,0.198 10 false 7 3.292,0.875 3.604,1.073 0.313,0.198 10 false 11 3.281,1.385 3.594,1.583 0.313,0.198 10 false 12 0.51,2.677 1.406,3.104 0.896,0.427 10 false Headlight Unit Assembly RH

B604976E07
3.417,2.563 4.823,3.031 1.406,0.469 10 false Outer Mirror Control ECU Assembly RH 3.292,1.083 5.583,1.281 2.292,0.198 10 false z9 3.292,1.594 5.583,1.792 2.292,0.198 10 false z9 3.292,1.385 5.583,1.583 2.292,0.198 10 false 12 3.302,0.906 5.594,1.104 2.292,0.198 10 false 16 4.708,1.438 7,1.635 2.292,0.198 10 false 7 4.677,0.917 6.969,1.115 2.292,0.198 10 false 11 4.219,1.083 6.51,1.281 2.292,0.198 10 false TRNI 4.229,1.604 6.521,1.802 2.292,0.198 10 false GND 4.667,1.604 5.104,2.01 0.438,0.406 10 false M1 4.656,1.094 5.094,1.5 0.438,0.406 10 false M1 4.635,4.865 5.292,5.281 0.656,0.417 10 false 4 4.417,4.844 4.833,5.25 0.417,0.406 10 false - 4.406,4.354 4.844,4.76 0.438,0.406 10 false B 2.552,5.396 2.885,5.583 0.333,0.188 10 false M21 5.76,6.917 7.083,7.49 1.323,0.573 10 false Combination Meter Assembly 2.552,5.542 4.198,5.74 1.646,0.198 10 false Outer Mirror Retractor RH 4.646,4.375 5.083,4.781 0.438,0.406 10 false 5 0.188,5.417 2.458,5.708 2.271,0.292 10 false Side Turn Signal Light Assembly RH 0.104,2.396 1.49,2.948 1.385,0.552 10 false Side Turn Signal Light Assembly RH 1.677,2.396 3.292,2.615 1.615,0.219 10 false Outer Mirror Retractor RH 0.104,0.125 3.323,0.5 3.219,0.375 12 false w/ Outer Mirror Control ECU Assembly: 0.083,3.406 3.302,3.781 3.219,0.375 12 false w/o Outer Mirror Control ECU Assembly: 3.583,1.094 5.875,1.292 2.292,0.198 10 false TRN+ 3.583,1.604 5.875,1.802 2.292,0.198 10 false TRN- 5.75,6.74 6.083,6.927 0.333,0.188 10 false I6

B604977E04
0.906,2.354 3.198,2.552 2.292,0.198 10 false Headlight Unit Assembly LH 0.458,1.865 2.75,2.063 2.292,0.198 10 false Headlight Lens Sub-assembly LH 3.406,2.573 4.698,2.979 1.292,0.406 10 false Headlight ECU Sub-assembly LH 3.323,1.083 5.615,1.281 2.292,0.198 10 false A 2.448,4.469 4.74,4.667 2.292,0.198 10 false B 3.281,1.406 5.573,1.604 2.292,0.198 10 false 20 3.333,0.906 5.625,1.104 2.292,0.198 10 false 6 4.677,1.427 6.969,1.625 2.292,0.198 10 false 12 4.677,0.906 6.969,1.104 2.292,0.198 10 false 11 4.26,1.115 6.552,1.313 2.292,0.198 10 false TNS 4.26,1.625 6.552,1.823 2.292,0.198 10 false GND 4.667,1.594 5.104,2 0.438,0.406 10 false B4 4.667,1.083 5.104,1.49 0.438,0.406 10 false B4 6.052,1.052 6.49,1.458 0.438,0.406 10 false LL 5.75,0.927 6.188,1.333 0.438,0.406 10 false 14 5.958,6.781 6.167,6.979 0.208,0.198 10 false I6 5.958,6.958 7.156,7.333 1.198,0.375 10 false Combination Meter Assembly 2.688,5.417 4.979,5.615 2.292,0.198 10 false Headlight Housing LH 0.208,5.406 2.5,5.604 2.292,0.198 10 false Headlight Lens Sub-assembly LH 4.688,4.479 5.125,4.885 0.438,0.406 10 false B3 0.104,0.125 2.698,0.427 2.594,0.302 12 false w/ Headlight ECU for LHD: 0.094,3.396 1.552,3.594 1.458,0.198 12 false w/o Headlight ECU: 4.719,4.302 5.156,4.708 0.438,0.406 10 false 8 4.719,4.802 4.906,4.99 0.188,0.188 10 false 7 4.24,4.833 4.563,5.021 0.323,0.188 10 false GND 4.417,4.354 4.583,4.531 0.167,0.177 10 false B 2.438,4.958 4.729,5.156 2.292,0.198 10 false B 2.458,4.281 2.896,4.688 0.438,0.406 10 false 1 2.458,4.802 2.896,5.208 0.438,0.406 10 false 4 4.656,4.958 5.094,5.365 0.438,0.406 10 false B3 3.302,1.594 5.594,1.792 2.292,0.198 10 false A

B671778E02
0.125,0.156 4.708,0.396 4.583,0.24 12 false w/ Headlight ECU for RHD: 0.344,1.885 1.604,2.271 1.26,0.385 10 false Headlight Lens Sub-assembly LH 2.042,2.854 3.292,3.219 1.25,0.365 10 false Headlight ECU Sub-assembly LH 5.927,3.833 6.24,4.031 0.313,0.198 10 false I6 5.917,3.99 7.094,4.354 1.177,0.365 10 false Combination Meter Assembly 3.51,2.406 6.115,2.604 2.604,0.198 10 false Headlight Cord LH 1.938,1.094 2.094,1.292 0.156,0.198 10 false B 1.927,1.594 2.083,1.792 0.156,0.198 10 false B 1.917,1.385 2.229,1.583 0.313,0.198 10 false 20 1.948,0.917 2.104,1.115 0.156,0.198 10 false 6 2.833,0.979 3.292,1.177 0.458,0.198 10 false TNS 2.854,1.469 3.313,1.667 0.458,0.198 10 false GND 4.698,0.885 4.854,1.083 0.156,0.198 10 false 7 4.708,1.385 4.865,1.583 0.156,0.198 10 false 1 3.25,1.094 3.708,1.292 0.458,0.198 10 false B88 3.25,1.583 3.708,1.781 0.458,0.198 10 false B88 0.479,2.635 1.396,3.063 0.917,0.427 10 false Headlight Unit Assembly LH 4.625,1.094 5.083,1.292 0.458,0.198 10 false BB6 4.625,1.583 5.083,1.781 0.458,0.198 10 false BB7 3.281,0.896 3.594,1.094 0.313,0.198 10 false 11 3.281,1.385 3.594,1.583 0.313,0.198 10 false 12

B604976E08
3.406,2.563 4.885,2.969 1.479,0.406 10 false Outer Mirror Control ECU Assembly LH 3.292,1.406 5.583,1.604 2.292,0.198 10 false 12 3.302,0.896 5.594,1.094 2.292,0.198 10 false 16 4.719,1.438 7.01,1.635 2.292,0.198 10 false 7 4.677,0.917 6.969,1.115 2.292,0.198 10 false 11 4.24,1.094 6.531,1.292 2.292,0.198 10 false TRNI 4.219,1.604 6.51,1.802 2.292,0.198 10 false GND 4.677,1.594 4.917,1.823 0.24,0.229 10 false N1 4.667,1.094 5.104,1.5 0.438,0.406 10 false N1 4.635,4.885 5.292,5.302 0.656,0.417 10 false 4 4.417,4.833 4.833,5.24 0.417,0.406 10 false - 4.406,4.354 4.844,4.76 0.438,0.406 10 false B 2.521,5.396 2.833,5.552 0.313,0.156 10 false N21 5.75,6.906 7.073,7.479 1.323,0.573 10 false Combination Meter Assembly 2.51,5.542 4.135,5.76 1.625,0.219 10 false Outer Mirror Retractor LH 4.646,4.375 5.083,4.781 0.438,0.406 10 false 5 0.167,5.417 2.438,5.708 2.271,0.292 10 false Side Turn Signal Light Assembly LH 0.104,2.396 1.469,2.792 1.365,0.396 10 false Side Turn Signal Light Assembly LH 3.25,1.583 3.583,1.792 0.333,0.208 10 false z10 1.677,2.385 3.26,2.583 1.583,0.198 10 false Outer Mirror Retractor LH 0.094,0.104 3.667,0.615 3.573,0.51 12 false w/ Outer Mirror Control ECU Assembly: 0.104,3.427 3.677,3.938 3.573,0.51 12 false w/o Outer Mirror Control ECU Assembly: 3.26,1.083 3.542,1.281 0.281,0.198 10 false z10 3.583,1.094 5.875,1.292 2.292,0.198 10 false TRN+ 3.583,1.615 5.875,1.813 2.292,0.198 10 false TRN- 5.75,6.74 6.063,6.896 0.313,0.156 10 false I6

B608402E01
5.792,7.688 6.938,8.438 1.146,0.75 10 false Combination Meter Assembly 0.271,2.781 2.458,3.323 2.188,0.542 10 false Rear Light Assembly RH 2.365,2.719 5.344,2.979 2.979,0.26 10 false g1 2.323,5.531 5.688,5.729 3.365,0.198 10 false b2 0.24,5.51 1.802,5.885 1.563,0.375 10 false Rear Combination Light Assembly RH 1.948,7.938 5.313,8.135 3.365,0.198 10 false b2 0.25,7.948 1.781,8.323 1.531,0.375 10 false Rear Combination Light Assembly RH 5.813,7.51 6.781,8.156 0.969,0.646 10 false I6 4.375,1.281 5.635,1.688 1.26,0.406 10 false 3 6,1.365 7.156,1.771 1.156,0.406 10 false TRNR 5.771,1.26 6.927,1.667 1.156,0.406 10 false 2 5.729,0.885 6.885,1.292 1.156,0.406 10 false 12 4.188,1.271 5.448,1.677 1.26,0.406 10 false B 3.948,0.927 5.208,1.333 1.26,0.406 10 false TRN6 5.99,1.01 7.146,1.417 1.156,0.406 10 false SYC1 3.938,4.125 4.969,4.323 1.031,0.198 10 false TRN1 3.927,3.667 5.208,4.01 1.281,0.344 10 false TRN2 3.948,1.615 5.281,1.99 1.333,0.375 10 false TRN4 3.948,1.958 6.5,2.219 2.552,0.26 10 false TRN3 4.375,4.146 5.583,4.583 1.208,0.438 10 false 3 4.385,3.656 6.01,4.021 1.625,0.365 10 false 2 4.375,1.979 6.042,2.177 1.667,0.198 10 false 1 4.375,1.625 5.854,1.792 1.479,0.167 10 false 2 4.156,5.042 6.208,5.385 2.052,0.344 10 false E 4.385,5.052 5.99,5.354 1.604,0.302 10 false 4 4.375,0.906 5.635,1.313 1.26,0.406 10 false 8 4.01,4.615 5.708,5 1.698,0.385 10 false TRN 4.375,4.573 5.5,4.813 1.125,0.24 10 false 1 3.292,6.885 6.656,7.083 3.365,0.198 10 false TRN 3.469,7.354 6.833,7.552 3.365,0.198 10 false E 3.688,7.365 7.052,7.563 3.365,0.198 10 false 4 3.667,6.875 7.031,7.073 3.365,0.198 10 false 1 0.135,6.167 5.448,6.552 5.313,0.385 12 false except Sequential Type Turn Signal Light (w/ Turn Light LED Type): 0.198,0.167 3.563,0.365 3.365,0.198 12 false for Sequential Type Turn Signal Light: 2.323,5.677 4.479,6.198 2.156,0.521 10 false Rear Combination Light Cord RH 1.927,8.094 4.146,8.5 2.219,0.406 10 false Rear Combination Light Cord RH 2.354,2.885 4.542,3.417 2.188,0.531 10 false Rear Light Socket and Wire RH 4.396,2.333 6.031,2.563 1.635,0.229 10 false 4 4.177,2.333 5.948,2.635 1.771,0.302 10 false E

B612066E02
5.302,3.396 7.156,3.656 1.854,0.26 10 false Combination Meter Assembly 0.313,2.281 0.625,2.479 0.313,0.198 10 false b2 0.302,2.458 3.563,2.802 3.26,0.344 10 false Rear Combination Light Cord RH 0.26,0.417 5.313,0.823 5.052,0.406 12 false except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type): 3.01,1.26 3.5,1.479 0.49,0.219 10 false TRN 3.208,1.698 3.698,1.917 0.49,0.219 10 false E 3.417,1.229 3.729,1.427 0.313,0.198 10 false 1 3.427,1.75 3.74,1.948 0.313,0.198 10 false 4 5.323,3.208 5.635,3.406 0.313,0.198 10 false I6

B608403E04
5.802,7.865 6.948,8.615 1.146,0.75 10 false Combination Meter Assembly 0.25,3.042 2.438,3.583 2.188,0.542 10 false Rear Light Assembly LH 2.375,3 5.354,3.26 2.979,0.26 10 false g2 2.323,5.802 5.688,6 3.365,0.198 10 false c2 0.26,5.813 1.823,6.188 1.563,0.375 10 false Rear Combination Light Assembly LH 1.948,8.198 5.313,8.396 3.365,0.198 10 false c2 0.25,8.219 1.781,8.594 1.531,0.375 10 false Rear Combination Light Assembly LH 5.802,7.708 6.771,8.354 0.969,0.646 10 false I6 4.385,1.563 5.646,1.969 1.26,0.406 10 false 3 6,1.677 7.156,2.083 1.156,0.406 10 false TRNL 5.781,1.552 6.938,1.958 1.156,0.406 10 false 1 4.188,1.563 5.448,1.969 1.26,0.406 10 false B 3.948,1.208 5.208,1.615 1.26,0.406 10 false TRN6 3.969,4.417 5,4.615 1.031,0.198 10 false TRN1 3.979,3.969 5.26,4.313 1.281,0.344 10 false TRN2 3.948,1.927 5.281,2.302 1.333,0.375 10 false TRN4 3.948,2.281 6.5,2.542 2.552,0.26 10 false TRN3 4.417,4.438 5.625,4.875 1.208,0.438 10 false 3 4.417,3.969 6.042,4.333 1.625,0.365 10 false 2 4.396,2.281 6.063,2.479 1.667,0.198 10 false 1 4.385,1.927 5.865,2.094 1.479,0.167 10 false 2 4.177,5.365 6.229,5.708 2.052,0.344 10 false E 4.396,5.354 6,5.656 1.604,0.302 10 false 4 4.385,1.188 5.646,1.594 1.26,0.406 10 false 8 4.021,4.885 5.719,5.271 1.698,0.385 10 false TRN 4.396,4.885 5.521,5.125 1.125,0.24 10 false 1 3.292,7.177 6.656,7.375 3.365,0.198 10 false TRN 3.469,7.677 6.833,7.875 3.365,0.198 10 false E 3.688,7.667 7.052,7.865 3.365,0.198 10 false 4 3.688,7.177 7.052,7.375 3.365,0.198 10 false 1 0.156,6.458 5.219,6.823 5.063,0.365 12 false except Sequential Type Turn Signal Light (w/ Turn Light LED Type): 0.198,0.406 3.563,0.604 3.365,0.198 12 false for Sequential Type Turn Signal Light: 2.323,5.927 4.479,6.448 2.156,0.521 10 false Rear Combination Light Cord LH 1.948,8.354 4.167,8.76 2.219,0.406 10 false Rear Combination Light Cord LH 2.344,3.167 4.531,3.698 2.188,0.531 10 false Rear Light Socket and Wire LH 4.396,2.594 6.031,2.823 1.635,0.229 10 false 4 4.177,2.604 5.948,2.906 1.771,0.302 10 false E

B612067E02
5.302,3.458 7.156,3.719 1.854,0.26 10 false Combination Meter Assembly 0.313,2.281 0.625,2.479 0.313,0.198 10 false c2 0.302,2.458 3.563,2.802 3.26,0.344 10 false Rear Combination Light Cord LH 0.26,0.417 5.313,0.823 5.052,0.406 12 false except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type): 3.01,1.26 3.5,1.479 0.49,0.219 10 false TRN 3.208,1.698 3.698,1.917 0.49,0.219 10 false E 3.417,1.229 3.729,1.427 0.313,0.198 10 false 1 3.427,1.75 3.74,1.948 0.313,0.198 10 false 4 5.302,3.25 5.615,3.448 0.313,0.198 10 false I6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the bulbs before performing the following procedure. (w/ Turn Light Bulb Type)


w/ Headlight ECU:

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>REGISTRATION

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH and side turn signal light LH do not blink. A
Front turn signal light RH and side turn signal light RH do not blink. B
Rear turn signal light LH does not blink. C
Rear turn signal light RH does not blink. D



A

2.CHECK VEHICLE TYPE

B

26.CHECK VEHICLE TYPE

C

50.CHECK VEHICLE TYPE

D

61.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

B

14.CHECK HEADLIGHT CORD LH

C

16.CHECK HEADLIGHT HOUSING LH
3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Disconnect the B4 headlight ECU sub-assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

4.CHECK VEHICLE TYPE

B

12.CHECK HEADLIGHT UNIT ASSEMBLY LH
4.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

5.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH

B

9.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
5.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

7.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the N1 outer mirror control ECU assembly LH connector.


c.

Disconnect the B4 headlight ECU sub-assembly LH connector.*1


d.

Disconnect the BB6 headlight cord LH connector.*2


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-14 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the z10 outer rear view mirror assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

B

8.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
8.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

9.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the N21 outer rear view mirror assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

11.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B4 headlight ECU sub-assembly LH connector.*1


c.

Disconnect the BB6 headlight cord LH connector.*2


d.

Disconnect the N21 outer rear view mirror assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-14 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

12.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Remove the headlight unit assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

B

13.CHECK HEADLIGHT LENS SUB-ASSEMBLY LH
13.CHECK HEADLIGHT LENS SUB-ASSEMBLY LH
a.

Remove the headlight lens sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE HEADLIGHT UNIT ASSEMBLY LH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

14.CHECK HEADLIGHT CORD LH
a.

Disconnect the BB6 headlight cord LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output. A
B150718 is output. B



A

4.CHECK VEHICLE TYPE

B

15.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
15.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Disconnect the B88 headlight ECU sub-assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

B

12.CHECK HEADLIGHT UNIT ASSEMBLY LH
16.CHECK HEADLIGHT HOUSING LH
a.

Disconnect the B3 headlight housing LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

17.CHECK VEHICLE TYPE

B

25.CHECK HEADLIGHT LENS SUB-ASSEMBLY LH
17.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

18.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH

B

22.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
18.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

20.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B3 headlight housing LH connector.


c.

Disconnect the N1 outer mirror control ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-14 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the z10 outer rear view mirror assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

B

21.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
21.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

22.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the N21 outer rear view mirror assembly LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

23.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

24.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
23.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B3 headlight assembly LH connector.


c.

Disconnect the N21 outer rear view mirror assembly LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-14 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

25.CHECK HEADLIGHT LENS SUB-ASSEMBLY LH
a.

Remove the headlight lens sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY LH

26.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Headlight ECU for LHD A
w/ Headlight ECU for RHD B
w/o Headlight ECU C



A

27.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

B

38.CHECK HEADLIGHT CORD RH

C

40.CHECK HEADLIGHT HOUSING RH
27.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Disconnect the B7 headlight ECU sub-assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

28.CHECK VEHICLE TYPE

B

36.CHECK HEADLIGHT UNIT ASSEMBLY RH
28.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

29.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH

B

33.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
29.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

30.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

31.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
30.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the M1 outer mirror control ECU assembly RH connector.


c.

Disconnect the B7 headlight ECU sub-assembly RH connector.*1


d.

Disconnect the BB8 headlight cord RH connector.*2


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-5 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the z9 outer rear view mirror assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

B

32.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
32.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

33.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the M21 outer rear view mirror assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

34.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

35.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
34.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B7 headlight ECU sub-assembly RH connector.*1


c.

Disconnect the BB8 headlight cord RH connector.*2


d.

Disconnect the M21 outer rear view mirror assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-5 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

36.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Remove the headlight unit assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

B

37.CHECK HEADLIGHT LENS SUB-ASSEMBLY RH
37.CHECK HEADLIGHT LENS SUB-ASSEMBLY RH
a.

Remove the headlight lens sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE HEADLIGHT UNIT ASSEMBLY RH

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

38.CHECK HEADLIGHT CORD RH
a.

Disconnect the B85 headlight cord RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output. A
B150718 is output. B



A

28.CHECK VEHICLE TYPE

B

39.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
39.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Disconnect the B7 headlight ECU sub-assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

B

36.CHECK HEADLIGHT UNIT ASSEMBLY RH
40.CHECK HEADLIGHT HOUSING RH
a.

Disconnect the B6 headlight housing RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

41.CHECK VEHICLE TYPE

B

49.CHECK HEADLIGHT LENS SUB-ASSEMBLY RH
41.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Outer Mirror Control ECU Assembly A
w/o Outer Mirror Control ECU Assembly B



A

42.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH

B

46.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
42.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

43.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

44.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
43.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B6 headlight housing RH connector.


c.

Disconnect the M1 outer mirror control ECU assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-5 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the z9 outer rear view mirror assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

B

45.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
45.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

46.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the M21 outer rear view mirror assembly RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

47.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

48.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
47.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the B6 headlight assembly RH connector.


c.

Disconnect the M21 outer rear view mirror assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-5 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

49.CHECK HEADLIGHT LENS SUB-ASSEMBLY RH
a.

Remove the headlight lens sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

B

REPLACE HEADLIGHT LENS SUB-ASSEMBLY RH

50.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Sequential Type Turn Signal Light A
except Sequential Type Turn Signal Light (w/ Turn Light LED Type) B
except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type) C



A

51.CHECK REAR LIGHT SOCKET AND WIRE LH

B

56.CHECK REAR COMBINATION LIGHT CORD LH

C

59.CHECK REAR COMBINATION LIGHT CORD LH
51.CHECK REAR LIGHT SOCKET AND WIRE LH
a.

Disconnect the g2 rear light socket and wire LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

52.CHECK REAR COMBINATION LIGHT CORD LH

B

55.CHECK REAR LIGHT ASSEMBLY LH
52.CHECK REAR COMBINATION LIGHT CORD LH
a.

Disconnect the c2 rear combination light cord LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

53.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

54.CHECK REAR COMBINATION LIGHT ASSEMBLY LH
53.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the g2 rear light socket and wire LH connector.


c.

Disconnect the c2 rear combination light cord LH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

54.CHECK REAR COMBINATION LIGHT ASSEMBLY LH
a.

Remove the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR COMBINATION LIGHT CORD LH

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

55.CHECK REAR LIGHT ASSEMBLY LH
a.

Remove the rear light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR LIGHT SOCKET AND WIRE LH

B

REPLACE REAR LIGHT ASSEMBLY LH

56.CHECK REAR COMBINATION LIGHT CORD LH
a.

Disconnect the c2 rear combination light cord LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

57.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

58.CHECK REAR COMBINATION LIGHT ASSEMBLY LH
57.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

58.CHECK REAR COMBINATION LIGHT ASSEMBLY LH
a.

Remove the rear combination light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR COMBINATION LIGHT CORD LH

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

59.CHECK REAR COMBINATION LIGHT CORD LH
a.

Disconnect the c2 rear combination light cord LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

60.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

REPLACE REAR COMBINATION LIGHT CORD LH

60.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the c2 rear combination light cord LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-1 (TRNL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

61.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Sequential Type Turn Signal Light A
except Sequential Type Turn Signal Light (w/ Turn Light LED Type) B
except Sequential Type Turn Signal Light (w/ Turn Light Bulb Type) C



A

62.CHECK REAR LIGHT SOCKET AND WIRE RH

B

67.CHECK REAR COMBINATION LIGHT CORD RH

C

70.CHECK REAR COMBINATION LIGHT CORD RH
62.CHECK REAR LIGHT SOCKET AND WIRE RH
a.

Disconnect the g2 rear light socket and wire RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

63.CHECK REAR COMBINATION LIGHT CORD RH

B

66.CHECK REAR LIGHT ASSEMBLY RH
63.CHECK REAR COMBINATION LIGHT CORD RH
a.

Disconnect the c2 rear combination light cord RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

64.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

65.CHECK REAR COMBINATION LIGHT ASSEMBLY RH
64.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the g1 rear light socket and wire RH connector.


c.

Disconnect the b2 rear combination light cord RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-2 (TRNR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

65.CHECK REAR COMBINATION LIGHT ASSEMBLY RH
a.

Remove the rear combination light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR COMBINATION LIGHT CORD RH

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

66.CHECK REAR LIGHT ASSEMBLY RH
a.

Remove the rear light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR LIGHT SOCKET AND WIRE RH

B

REPLACE REAR LIGHT ASSEMBLY RH

67.CHECK REAR COMBINATION LIGHT CORD RH
a.

Disconnect the c2 rear combination light cord LH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

68.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

69.CHECK REAR COMBINATION LIGHT ASSEMBLY RH
68.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-2 (TRNR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

69.CHECK REAR COMBINATION LIGHT ASSEMBLY RH
a.

Remove the rear combination light assembly RH connector.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

REPLACE REAR COMBINATION LIGHT CORD RH

B

REPLACE REAR COMBINATION LIGHT ASSEMBLY

70.CHECK REAR COMBINATION LIGHT CORD RH
a.

Disconnect the b2 rear combination light cord RH connector.


b.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

c.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150819 is output. A
DTC B150718 is output. B



A

71.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

REPLACE REAR COMBINATION LIGHT CORD RH

71.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the b2 rear combination light cord RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-2 (TRNR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR