Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  Engine Knocking or Rattling  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Knocking and abnormal sound due to extremely rich combustion

·

Abnormal sound due to friction between parts


1.

Injector malfunctions

-

Injector sliding malfunction

-

Injector stuck closed

-

Injector stuck open

-

Deposits in injector

-

Injector circuit malfunction


2.

Abnormal common rail pressure

-

Fuel supply pump

-

Fuel pulsation sound

-

Air in fuel


3.

Friction between parts

4.

Compression pressure


·

Injector compensation codes

·

Fuel leakage

·

Intake air system leakage

·

Intake air system blockage

·

EGR system

·

Throttle valve system

·

Fuel pressure sensor

·

Manifold absolute pressure sensor

·

Atmospheric pressure sensor (built into ECM)

·

Vehicle modifications

·

Low quality fuel

·

Lack of fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:
·

This troubleshooting procedure checks for knocking and rattling.

·

Knocking is most likely to occur while the engine is idling.



PROCEDURE

1.CHECK SOUND AREA
a.

Find the source of the abnormal sound using a mechanic's stethoscope.

Result:
Result Proceed to
Sound from fuel supply pump A
Sound from parts other than fuel supply pump B




A

2.CHECK HARNESS AND CONNECTOR IN ENGINE COMPARTMENT

B

REPAIR OR REPLACE MALFUNCTION PARTS

2.CHECK HARNESS AND CONNECTOR IN ENGINE COMPARTMENT
a.

Check the wire harness connections.

OK:

Wire harnesses are connected securely.



Result:
Proceed to
OK
NG



OK

3.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to set DTCs relating to malfunctions of the fuel system, EGR system, and throttle valve. If DTCs are set, problem areas can be identified.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.



d.

Fully warm up the engine.


e.

Allow the engine to idle for 5 minutes or more.


f.

Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (procedure "A").


g.

Decelerate and stop the vehicle (procedure "B").


h.

Repeat procedure "A" and procedure "B" 4 times or more.


i.

Stop the engine and wait for at least 10 seconds (procedure "C").


j.

Repeat procedure "A" and procedure "C" described above to set DTCs relating to the EGR system and throttle valve.


k.

Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to set DTCs relating to the fuel supply pump).


Result:
Proceed to
NEXT



NEXT

4.READ OUTPUT DTC (RELATED TO ENGINE)
4.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Result Proceed to
No DTC is output A
Engine related DTCs B




A

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.

Powertrain > Engine and ECT > Active Test
Tester Display
Test the Fuel Leak
50004 61 90

d.

Visually check the fuel supply pump, injector, and fuel line located between the fuel supply pump and common rail for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail and the injector.

HINT:

There may be fuel leaks inside the components, such as the fuel supply pump.


OK:

No fuel leakage.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (MAP, MAF, FUEL PRESS)

NG

REPAIR OR REPLACE FUEL LEAKAGE POINT

6.READ VALUE USING GTS (MAP, MAF, FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
MAP
Fuel Press
50003 61 319,314,54

d.

Enter the following menus in order and read the values.

·

MAP

·

MAF

·

Fuel Press


Standard value:
Item Engine Speed* Reference Value Description
MAP Ignition switch ON (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
Idling 90 to 102 kPa (675 to 765 mmHg, 0.0171 to 0.0194 in.Hg)
3000 rpm (no engine load) 110 to 150 kPa (825 to 1125 mmHg, 0.0210 to 0.0286 in.Hg)
3000 rpm (driving with full throttle acceleration) 150 to 210 kPa (1125 to 1575 mmHg, 0.0286 to 0.0400 in.Hg)
3500 rpm (driving with full throttle acceleration) 145 to 210 kPa (1088 to 1575 mmHg, 0.0276 to 0.0400 in.Hg)
4000 rpm (driving with full throttle acceleration) 130 to 187 kPa (975 to 1402 mmHg, 0.0248 to 0.0356 in.Hg)
MAF Ignition switch ON (engine stopped) 0 to 5 gm/sec. Intake air volume detected by mass air flow meter
Idling 6.1 to 26.5 gm/sec.
3000 rpm (no engine load) 68 to 170 gm/sec.
3000 rpm (driving with full throttle acceleration) 150 to 210 gm/sec.
3500 rpm (driving with full throttle acceleration) 160 to 230 gm/sec.
4000 rpm (driving with full throttle acceleration) 160 to 230 gm/sec.
Fuel Press Idling 27000 to 37000 kPa Common rail internal fuelpressure
2000 rpm (no engine load) 50000 to 70000 kPa
3000 rpm (no engine load) 52000 to 76000 kPa
3000 rpm (driving with full throttle acceleration) 125000 to 155000 kPa
3500 rpm (driving with full throttle acceleration) 155000 to 180000 kPa
4000 rpm (driving with full throttle acceleration) 160000 to 180000 kPa


HINT:

*: The A/C switch and all accessory switches should be OFF with a fully warm engine.


Result:
Item Result Proceed to
MAP, MAF and Fuel Press Standard range A
MAP and MAF Outside standard range B
Only MAP Outside standard range C
Only MAF Outside standard range D
Only Fuel Press Outside standard range E




A

7.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)

B

11.CHECK INTAKE SYSTEM

C

GO TO DTC P0105, P0107 AND P0108 (RELATED TO MANIFOLD ABSOLUTE PRESSURE SENSOR)

D

GO TO DTC P0100, P0102 AND P0103 (RELATED TO MASS AIR FLOW METER)

E

28.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
7.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine, warm it up and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 376,368,369,370,371,372,373,374,375

d.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1 to #8

·

Injection Volume


Standard value:
Item Engine Speed* Reference Value Description
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3 Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
·

Positive values indicate control which corrects combustion degradation

·

Negative values indicate control which corrects excessive combustion pressure

·

If problems exist, "Injection Feedback Val" may deviate from the -3.0 and 3.0 mm3 range


Injection Volume Idling 3.0 to 10 mm3 Fuel injection volume value controlled by ECU
·

Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, boost pressure, atmospheric pressure, EGR volume, and MAF

·

If problems exist, "Injection Volume" may be outside the standard range




HINT:

*: The A/C switch and all accessory switches should be OFF with a fully warm engine.


Result:
Result Proceed to
Standard range A
Injection Feedback Val #1 to #8 and/or Injection Volume outside standard range B




A

8.CHECK INJECTOR COMPENSATION CODE

B

14.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
8.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions.



b.

Check the injector compensation code.

OK:

Compensation code of the installed injector is the same as the code registered in the ECM.



Result:
Proceed to
OK
NG



OK

9.RESET ECM

NG

REGISTER INJECTOR COMPENSATION CODE

9.RESET ECM
a.

Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.


b.

Reconnect the cable to the negative (-) battery terminal.


c.

Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

NG

10.BASIC INSPECTION
10.BASIC INSPECTION
a.

Check the fuel quality.


b.

Check the fuel for air.


c.

Check the fuel system for blockages.


d.

Check the air filter.


e.

Check the engine oil.


f.

Check the engine coolant.


g.

Check the engine idling speed and the maximum engine speed.


h.

Check the vacuum pump.

OK:

Each inspection result is normal.



Result:
Proceed to
OK
NG



OK

11.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

11.CHECK INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

OK:

No air leakage or blockage.



Result:
Proceed to
OK
NG



OK

12.CHECK EGR VALVE ASSEMBLY (NO. 1 AND NO. 2)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

12.CHECK EGR VALVE ASSEMBLY (NO. 1 AND NO. 2)
HINT:

In this inspection, measure the MAF rate while idling the engine with the EGR valve fully closed.


a.

Make sure the engine is stopped.


b.

Disconnect the EGR valve connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON and turn the GTS on.


e.

Start the engine.


f.

Enter the following menu items: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 61 319

g.

Measure the MAF rate while idling the engine.

Standard rate:

MAF rate is between 14.2 and 26.5 gm/sec.


HINT:
·

Standard MAF rate while idling the engine with the EGR valve operating: 6.1 to 26.5 gm/sec.

·

With the EGR valve connector disconnected, a DTC is set when the ignition switch is turned to ON. Therefore, clear the DTC upon completion of the inspection above.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR




Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (ACTUAL THROTTLE POSITION)

NG

13.READ VALUE USING GTS (ACTUAL THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle Position and Actual Throttle Position #2.

Powertrain > Engine and ECT > Data List
Tester Display
Actual Throttle Position
Actual Throttle Position #2
50003 61 406,572

d.

Read the value.

Standard value:

Ignition switch ON: 0%

Idling (warmed up engine): 0 to 90%

Accelerator pedal fully depressed: 0%



Result:
Proceed to
OK
NG



NG

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or for Bank 2)

OK

16.CHECK COMBUSTION SOUND
14.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
a.

Follow the instructions in the table below according to the check result of the GTS.

HINT:

This operation is based on the premise that the common rail pressure is normal.


Standard value:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3
Injection Volume Idling 3.0 to 10.0 mm3


HINT:

*: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.


Result:
Injection Feedback Val #1 to #8 Injection Volume Proceed to
3.0 mm3/st or more, -3.0 mm3/st or less Less than 3.0 mm3/st A
Between 3.0 and 10 mm3/st (Normal) B
More than 10 mm3/st B
Between -3.0 and 3.0 mm3/st Less than 3.0 mm3/st -
Between 3.0 and 10 mm3/st (Normal) Normal
More than 10 mm3/st C*


HINT:

*: When the Injection Volume displayed on the tester is large despite the Fuel Press and Injection Feedback Val #1 to #8 in the Data List being normal, the injector may be clogged. In this case, there may be deposits inside or outside the tip of the injector.


Proceed to Inspection Area Description
A Inspect and repair cylinder injector withrevised injection volume of less than 3.0 mm3/st:
·

Perform power balance inspection and identify malfunctioning cylinder

·

Replace malfunctioning cylinder injector


Abnormal value cylinder injector injects excessively large quantity of fuel
B Identify malfunctioning cylinders by conducting power balance inspection:
·

Perform power balance inspection to identify malfunctioning cylinders

·

Clean malfunctioning cylinder injector, then check and repair it


Abnormal value cylinder injector injects excessively large quantity of fuel
·

Fuel injection volume too low due to injector nozzle being blocked by deposits

·

Abnormal value cylinder injector compression decreases

·

Abnormal value cylinder injector injects excessively large quantity of fuel


C Inspect and repair all cylinder injectors:
Clean all cylinder injectors, and then inspect and repair them
All cylinder injectors inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector nozzles being blocked by deposits

HINT:
·

Despite the injector functioning normally, the indicated Injection Feedback Val #1 to #8 value may be outside the normal operating range due to compensation for other problems (such as low compression).

·

Injection Feedback Val #1 to #8 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #8 may deviate from the standard range.





A

15.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

B

19.CHECK MALFUNCTIONING CYLINDER'S INJECTOR FOR DEPOSITS

C*

22.CHECK INJECTORS FOR DEPOSITS
15.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the 8 cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

HINT:
·

If the engine idle speed does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

REPLACE INJECTOR OF MALFUNCTIONING CYLINDER

16.CHECK COMBUSTION SOUND
a.

Confirm type of sound emitted.

Result:
Result Proceed to
Knocking A
Mechanical sound other than knocking B




A

17.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTION)

B

25.CHECK SOUND AREA
17.PERFORM ACTIVE TEST USING GTS (FUEL CUT FOR IDENTIFYING MALFUNCTION)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the 8 cylinders in sequence to identify any faulty cylinders by performing the power balance inspection.

HINT:
·

While the engine is idling, if the idling stability variation is small despite cutting off the fuel injection, the cylinder is malfunctioning.

·

With normal cylinders, the engine idles roughly when the fuel injection is cut off.




Result:
Proceed to
NEXT



NEXT

18.CHECK CYLINDER COMPRESSION PRESSURE
18.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

19.CHECK MALFUNCTIONING CYLINDER'S INJECTOR FOR DEPOSITS

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

19.CHECK MALFUNCTIONING CYLINDER'S INJECTOR FOR DEPOSITS
HINT:

If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

20.CLEAN INJECTOR

B

REPLACE INJECTOR OF MALFUNCTIONING CYLINDER

20.CLEAN INJECTOR
a.

Wipe away deposits from the tips of the injectors.

HINT:

Solvent or carbon removal agents help remove the deposits easily.


NOTICE:

Exercise extreme care not to damage the injectors while wiping off the deposits.



Result:
Proceed to
NEXT



NEXT

21.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
21.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS on.


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 376,368,369,370,371,372,373,374,375

f.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1 to #8

·

Injection Volume


Standard value:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3
Injection Volume Idling 3.0 to 10 mm3


HINT:
·

*: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.

·

When the values are outside the standard range, deposits inside the injector may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR OF MALFUNCTIONING CYLINDER

22.CHECK INJECTORS FOR DEPOSITS
HINT:

If an injector is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector for any deposits.


Result:
Result Proceed to
Deposits A
No deposits B



A

23.CLEAN INJECTOR

B

REPLACE INJECTOR OF MALFUNCTIONING CYLINDER

23.CLEAN INJECTOR
a.

Wipe away deposits from the tips of the injectors.

HINT:

Solvent or carbon removal agents help remove the deposits easily.


NOTICE:

Exercise extreme care not to damage the injectors while wiping off the deposits.



Result:
Proceed to
NEXT



NEXT

24.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
24.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector to the cylinder head.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and turn the GTS on.


d.

Start the engine and warm it up.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 376,368,369,370,371,372,373,374,375

f.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1 to #8

·

Injection Volume


Standard value:
Item Engine Speed* Reference Value
Injection Feedback Val #1 to #8 Idling -3.0 to 3.0 mm3
Injection Volume Idling 3.0 to 10 mm3


HINT:
·

*: The A/C switch and all accessory switches should be OFF, and the engine should be fully warmed up.

·

When the values are outside the standard range, deposits inside the injector may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR OF MALFUNCTIONING CYLINDER

25.CHECK SOUND AREA
a.

Find the source of the abnormal sound using a mechanic's stethoscope.

Result:
Result Proceed to
Sound from fuel supply pump A
Sound from parts other than fuel supply pump B




A

26.BLEED AIR FROM FUEL SYSTEM

B

REPAIR OR REPLACE MALFUNCTIONING PARTS

26.BLEED AIR FROM FUEL SYSTEM
a.

To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.


Result:
Proceed to
NEXT



NEXT

27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
27.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the knocking has been successfully repaired by performing a driving test.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

28.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
28.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.
A168115C01
1.448,1.427 1.927,1.729 0.479,0.302 1.885,2.271 2.5,2.052 true 1.552,2.281 0.938,2.052 true 0.135,0.073 0.427,0.344 0.292,0.271 10 false *a 1.573,1.5 1.865,1.667 0.292,0.167 10 false rC1 0.531,1.969 0.875,2.167 0.344,0.198 10 false PCV 2.563,1.969 2.802,2.135 0.24,0.167 10 false +B
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve)


Disconnect the rC1 fuel temperature sensor, suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
rC1-1 (PCV) - rC1-2 (+B) 20°C (68°F) 1.9 to 2.3 Ω



Result:
Proceed to
OK
NG



OK

29.INSPECT COMMON RAIL RH (FUEL PRESSURE SENSOR)

NG

29.INSPECT COMMON RAIL RH (FUEL PRESSURE SENSOR)
a.
A165963C01
1.458,2.375 1.125,2.833 true 1.729,2.385 1.74,2.833 true 2.083,2.365 2.375,2.823 true 0.24,0.469 1.198,0.938 0.958,0.469 10 false *a 0.99,2.844 1.229,3.021 0.24,0.177 10 false VC 1.635,2.844 1.875,3.021 0.24,0.177 10 false PR 2.292,2.844 2.531,3.021 0.24,0.177 10 false E2
*a Component without harness connected
(Fuel Pressure Sensor)


Disconnect the C56 fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
2 (PR) - 1 (E2) Always 16.4 kΩ or less
2 (PR) - 3 (VC) Always 3 kΩ or less



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL AND FUEL SYSTEM (FUEL FILTER OR FUEL LINE)

NG