Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1401

DTC No. Detection Item DTC Detection Condition Trouble Area
C1405 Open or Short in Front Speed Sensor RH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH

·

Skid control sensor wire RH

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)


C1406 Open or Short in Front Speed Sensor LH Circuit Either condition is met:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor LH

·

Skid control sensor wire LH

·

Speed sensor circuit

·

Brake actuator assembly (Skid control ECU)



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

C311981E01
0.479,0.573 2.031,0.792 1.552,0.219 10 false Front Speed Sensor RH 0.458,2 1.948,2.25 1.49,0.25 10 false Front Speed Sensor LH 2.844,0.333 3,0.531 0.156,0.198 10 false A 2.844,0.875 3,1.073 0.156,0.198 10 false A 2.844,0.135 3,0.333 0.156,0.198 10 false 3 2.833,1.875 2.99,2.073 0.156,0.198 10 false B 2.844,0.688 3,0.885 0.156,0.198 10 false 1 2.406,0.323 2.865,0.521 0.458,0.198 10 false FR+ 3.573,0.458 4.031,0.656 0.458,0.198 10 false FR+ 6.115,0.333 6.573,0.531 0.458,0.198 10 false FR+ 4,0.156 4.156,0.354 0.156,0.198 10 false 2 3.958,0.333 4.271,0.531 0.313,0.198 10 false B3 4.292,0.333 4.75,0.531 0.458,0.198 10 false I18 4.333,0.156 4.49,0.354 0.156,0.198 10 false 2 3.958,0.531 4.271,0.729 0.313,0.198 10 false *1 4.292,0.531 4.604,0.729 0.313,0.198 10 false *2 3.969,0.885 4.281,1.083 0.313,0.198 10 false B3 4.292,0.885 4.75,1.083 0.458,0.198 10 false I18 4.01,0.708 4.167,0.906 0.156,0.198 10 false 1 4.333,0.708 4.49,0.906 0.156,0.198 10 false 1 3.958,1.094 4.271,1.292 0.313,0.198 10 false *1 4.313,1.094 4.625,1.292 0.313,0.198 10 false *2 3.073,1.271 5.073,1.469 2,0.198 10 false Skid Control Sensor Wire RH 2.427,0.865 2.885,1.063 0.458,0.198 10 false FR- 3.573,0.771 4.031,0.969 0.458,0.198 10 false FR- 6.125,0.875 6.583,1.073 0.458,0.198 10 false FR- 5.885,0.219 6.042,0.417 0.156,0.198 10 false 7 5.875,0.771 6.031,0.969 0.156,0.198 10 false 6 2.823,2.458 2.979,2.656 0.156,0.198 10 false B 2.844,1.708 3.01,1.896 0.167,0.188 10 false 3 2.823,2.26 2.979,2.458 0.156,0.198 10 false 1 2.385,1.885 2.844,2.083 0.458,0.198 10 false FL+ 3.594,2.01 4.052,2.208 0.458,0.198 10 false FL+ 6.125,1.896 6.583,2.094 0.458,0.198 10 false FL+ 2.385,2.458 2.844,2.656 0.458,0.198 10 false FL- 3.594,2.344 4.052,2.542 0.458,0.198 10 false FL- 6.135,2.458 6.594,2.656 0.458,0.198 10 false FL- 5.823,1.76 6.135,1.958 0.313,0.198 10 false 19 5.823,2.323 6.135,2.521 0.313,0.198 10 false 18 3.99,1.698 4.156,1.885 0.167,0.188 10 false 3 3.979,2.271 4.135,2.469 0.156,0.198 10 false 1 3.917,1.885 4.375,2.083 0.458,0.198 10 false A21 3.927,2.458 4.385,2.656 0.458,0.198 10 false A21 3.021,2.802 4.969,3.063 1.948,0.26 10 false Skid Control Sensor Wire LH 5.5,2.844 7.146,3.292 1.646,0.448 10 false Brake Actuator Assembly (Skid Control ECU) 5.49,2.677 5.948,2.875 0.458,0.198 10 false A20 0.094,3.031 2.094,3.313 2,0.281 10 false *1: for 1VD-FTV and 1GR-FE 0.094,3.354 2.094,3.635 2,0.281 10 false *2: for 1HZ

CAUTION / NOTICE / HINT

NOTICE:
·

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Normal -
FL Speed Open Front speed sensor LH open detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FR/FL WHEEL SPEED)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error.

This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output

4.INSPECT SKID CONTROL SENSOR WIRE

b.
C269772C04
0.25,0.781 0.469,1 0.219,0.219 2.833,0.615 3.167,0.833 0.333,0.219 0.208,2.552 0.438,2.771 0.229,0.219 2.865,2.573 3.208,2.792 0.344,0.219 2.844,1.063 3.177,1.281 0.333,0.219 0.938,0.885 0.854,0.219 0.854,0.219 0.74,0.219 false 1.24,0.875 1.333,0.208 1.333,0.208 1.438,0.208 false 0.948,2.583 0.854,1.979 0.854,1.979 0.75,1.979 false 1.26,2.583 1.344,2 1.344,2 1.438,2 false 2.219,0.896 2.167,0.417 2.167,0.417 2.083,0.417 true 2.396,0.927 2.417,0.25 2.417,0.25 2.5,0.25 true 2.5,2.594 2.667,2.167 2.667,2.167 2.833,2.167 true 2.094,2.656 1.75,2.917 1.75,2.917 1.75,3.083 true 3.104,0.406 3.417,0.563 0.313,0.156 10 false *A 3.125,2.406 3.365,2.563 0.24,0.156 10 false *C 0.073,0.073 0.385,0.229 0.313,0.156 10 false *1 1.031,1.344 1.344,1.5 0.313,0.156 10 false *a 2.26,1.969 2.573,2.125 0.313,0.156 10 false *b 2.99,2.823 3.302,2.979 0.313,0.156 10 false *c 0.49,0.146 0.792,0.333 0.302,0.188 10 false FR- 1.75,0.323 2.115,0.5 0.365,0.177 10 false FR+ 0.323,0.802 0.479,1 0.156,0.198 10 false A 2.927,0.646 3.26,0.823 0.333,0.177 10 false B3 0.292,0.583 0.76,0.771 0.469,0.188 10 false *A, *B 0.49,1.896 0.802,2.063 0.313,0.167 10 false FL- 1.5,1.906 1.813,2.083 0.313,0.177 10 false FL+ 0.281,2.573 0.438,2.771 0.156,0.198 10 false B 2.927,2.604 3.219,2.781 0.292,0.177 10 false A21 0.375,2.385 0.688,2.583 0.313,0.198 10 false *C 1.021,3.052 1.333,3.25 0.313,0.198 10 false *a 2.26,3.24 2.573,3.417 0.313,0.177 10 false *b 3.198,0.667 3.427,0.969 0.229,0.302 10 false *c 2.906,1.094 3.24,1.271 0.333,0.177 10 false I18 3.115,0.885 3.427,1.042 0.313,0.156 10 false *B 3.198,1.094 3.427,1.396 0.229,0.302 10 false *c 1.5,0.125 1.865,0.302 0.365,0.177 10 false FR+ 2.563,0.177 2.865,0.365 0.302,0.188 10 false FR- 2.854,2.083 3.167,2.25 0.313,0.167 10 false FL- 1.667,3.083 1.979,3.26 0.313,0.177 10 false FL+
*A for RH (1VD-FTV and 1GR-FE)
*B for RH (1HZ)
*C for LH
*1 Skid Control Sensor Wire
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)
*c Male


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (1VD-FTV and 1GR-FE)
Tester Connection Condition Specified Condition
B3 male connector 1 (FR-) - A-1 (FR-) Always Below 1 Ω
B3 male connector 1 (FR-) or A-1 (FR-) - Body ground Always 10 kΩ or higher
B3 male connector 2 (FR+) - A-3 (FR+) Always Below 1 Ω
B3 male connector 2 (FR+) or A-3 (FR+) - Body ground Always 10 kΩ or higher
A-1 (FR-) - A-3 (FR+) Always 10 kΩ or higher

for RH (1HZ)
Tester Connection Condition Specified Condition
I18 male connector 1 (FR-) - A-1 (FR-) Always Below 1 Ω
I18 male connector 1 (FR-) or A-1 (FR-) - Body ground Always 10 kΩ or higher
I18 male connector 2 (FR+) - A-3 (FR+) Always Below 1 Ω
I18 male connector 2 (FR+) or A-3 (FR+) - Body ground Always 10 kΩ or higher
A-1 (FR-) - A-3 (FR+) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A21 male connector 1 (FL-) - B-1 (FL-) Always Below 1 Ω
A21 male connector 1 (FL-) or B-1 (FL-) - Body ground Always 10 kΩ or higher
A21 male connector 3 (FL+) - B-3 (FL+) Always Below 1 Ω
A21 male connector 3 (FL+) or B-3 (FL+) - Body ground Always 10 kΩ or higher
B-1 (FL-) - B-3 (FL+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.

Disconnect the A and/or B speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A20-7 (FR+) - A-3 (FR+) Always Below 1 Ω
A20-7 (FR+) or A-3 (FR+) - Body ground Always 10 kΩ or higher
A20-6 (FR-) - A-1 (FR-) Always Below 1 Ω
A20-6 (FR-) or A-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A20-19 (FL+) - B-3 (FL+) Always Below 1 Ω
A20-19 (FL+) or B-3 (FL+) - Body ground Always 10 kΩ or higher
A20-18 (FL-) - B-1 (FL-) Always Below 1 Ω
A20-18 (FL-) or B-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FR+/FL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FR+/FL+ TERMINAL)
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.
C269767C02
1.583,0.115 1.781,0.313 0.198,0.198 1.583,0.396 1.781,0.583 0.198,0.188 1.938,1.344 2.76,1.49 2.76,1.49 2.76,1.594 false 1.802,0.063 2.115,0.219 0.313,0.156 10 false *A 1.802,0.365 2.115,0.521 0.313,0.156 10 false *B 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.635,0.135 1.792,0.333 0.156,0.198 10 false A 1.635,0.406 1.792,0.604 0.156,0.198 10 false B 2.563,1.635 3.021,1.833 0.458,0.198 10 false FR+ 2.563,1.813 2.875,2.01 0.313,0.198 10 false FL+ 2.813,1.615 3.125,1.813 0.313,0.198 10 false *A, 2.813,1.802 3.125,2 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A-3 (FR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
B-3 (FL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG