Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1415  Rear Speed Sensor RH Output Malfunction  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1403

DTC No. Detection Item DTC Detection Condition Trouble Area
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Stored only during test mode.
·

Rear speed sensor RH

·

Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)


C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Stored only during test mode.
·

Rear speed sensor LH

·

Rear axle hub and bearing assembly LH (Rear speed sensor rotor LH)


C1415 Rear Speed Sensor RH Output Malfunction One of the following conditions is met:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH

·

Skid control sensor wire

·

Speed sensor circuit

·

Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)

·

Brake actuator assembly (Skid control ECU)


C1416 Rear Speed Sensor LH Output Malfunction One of the following conditions is met:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor LH

·

Skid control sensor wire

·

Speed sensor circuit

·

Rear axle hub and bearing assembly LH (Rear speed sensor rotor LH)

·

Brake actuator assembly (Skid control ECU)



HINT:
·

DTCs C1415 and C1277 are for the rear speed sensor RH.

·

DTCs C1416 and C1278 are for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Normal -
RL Speed Open Rear speed sensor LH open detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RR/RL WHEEL SPEED)

NG

8.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error.

This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform the sensor check in the Test Mode Procedure.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All test mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output

12.REPLACE REAR SPEED SENSOR
5.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C144929C11
1.156,2.771 0.979,2.771 0.979,2.771 0.698,2.49 false 0.083,0.083 0.396,0.24 0.313,0.156 10 false *1 1.198,2.708 1.51,2.865 0.313,0.156 10 false *a 0.615,2.896 0.927,3.052 0.313,0.156 10 false *b 2.698,2.948 3.01,3.104 0.313,0.156 10 false *c
*1 Rear Speed Sensor
*a No Clearance
*b OK
*c NG


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(w/ ABS)>INSTALLATION

OK:

There is no clearance between the sensor and the rear axle.

The installation nut is tightened properly.



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

6.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.



Result:
Proceed to
OK
NG



OK

7.INSPECT REAR SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

7.INSPECT REAR SPEED SENSOR ROTOR
a.

Remove the rear axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

8.INSPECT SKID CONTROL SENSOR WIRE

NG

CLEAN OR REPLACE REAR SPEED SENSOR ROTOR

8.INSPECT SKID CONTROL SENSOR WIRE
a.

Install the rear axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>INSTALLATION



C269768C04
1.198,0.813 1.365,1 0.167,0.188 3.427,0.542 3.729,0.74 0.302,0.198 5.844,0.833 6.021,1.01 0.177,0.177 0.635,2.115 0.635,2.021 0.635,2.021 1.042,1.563 false 1.927,2.125 1.927,2.021 1.927,2.021 1.51,1.573 false 5.385,2.146 5.385,2.021 5.385,2.021 5.698,1.563 false 6.479,2.135 6.479,2.031 6.479,2.031 6.177,1.563 false 3.792,1.344 4.167,0.833 4.167,0.833 4.25,0.833 true 3.458,1.344 3.167,0.833 3.167,0.833 3.083,0.833 true 3.427,1.573 2.917,1.917 2.917,1.917 2.917,2.083 true 3.792,1.583 4.25,1.917 4.25,1.917 4.25,2.083 true 6.094,0.708 6.406,0.865 0.313,0.156 10 false *A 1.417,0.688 1.729,0.844 0.313,0.156 10 false *B 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 1.208,2.229 1.521,2.385 0.313,0.156 10 false *a 3.563,2.146 3.875,2.302 0.313,0.156 10 false *b 3.76,0.406 4.073,0.563 0.313,0.156 10 false *c 1.24,0.833 1.396,1.031 0.156,0.198 10 false D 3.5,0.563 3.823,0.75 0.323,0.188 10 false V3 5.885,0.844 6.042,1.042 0.156,0.198 10 false C 0.552,2.146 0.865,2.333 0.313,0.188 10 false RL- 1.813,2.156 2.115,2.323 0.302,0.167 10 false RL+ 5.302,2.167 5.604,2.354 0.302,0.188 10 false RR- 6.375,2.167 6.677,2.344 0.302,0.177 10 false RR+ 5.896,2.292 6.104,2.479 0.208,0.188 10 false *a 4.281,0.76 4.594,0.948 0.313,0.188 10 false RL- 2.781,0.75 3.083,0.917 0.302,0.167 10 false RL+ 2.823,2.094 3.125,2.271 0.302,0.177 10 false RR+ 4.167,2.125 4.469,2.313 0.302,0.188 10 false RR-
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)
*c Female - -



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
V3 female connector 3 (RR+) - C-3 (RR+) Always Below 1 Ω
V3 female connector 3 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
V3 female connector 4 (RR-) - C-1 (RR-) Always Below 1 Ω
V3 female connector 4 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 1 (RL+) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 3 (RR+) - V3 female connector 4 (RR-) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
V3 female connector 1 (RL+) - D-3 (RL+) Always Below 1 Ω
V3 female connector 1 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
V3 female connector 2 (RL-) - D-1 (RL-) Always Below 1 Ω
V3 female connector 2 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 2 (RL-) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 3 (RR+) Always 10 kΩ or higher
V3 female connector 1 (RL+) - V3 female connector 4 (RR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


c.

Disconnect the C and/or D speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A20-17 (RR+) - C-3 (RR+) Always Below 1 Ω
A20-17 (RR+) or C-3 (RR+) - Body ground Always 10 kΩ or higher
A20-16 (RR-) - C-1 (RR-) Always Below 1 Ω
A20-16 (RR-) or C-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A20-5 (RL+) - D-3 (RL+) Always Below 1 Ω
A20-5 (RL+) or D-3 (RL+) - Body ground Always 10 kΩ or higher
A20-4 (RL-) - D-1 (RL-) Always Below 1 Ω
A20-4 (RL-) or D-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RR+/RL+ TERMINAL)
a.

Connect the brake actuator assembly (skid control ECU) connector.


b.
C269769C03
1.604,0.135 1.833,0.333 0.229,0.198 1.604,0.406 1.833,0.594 0.229,0.188 2,1.281 2.698,1.469 2.698,1.469 2.698,1.563 false 1.885,0.083 2.198,0.24 0.313,0.156 10 false *A 1.885,0.375 2.198,0.531 0.313,0.156 10 false *B 1.667,0.146 1.823,0.344 0.156,0.198 10 false C 1.667,0.417 1.823,0.615 0.156,0.198 10 false D 2.49,1.583 2.948,1.781 0.458,0.198 10 false RR+ 2.49,1.75 2.948,1.948 0.458,0.198 10 false RL+ 2.76,1.583 3.073,1.781 0.313,0.198 10 false *A, 2.75,1.75 3.063,1.948 0.313,0.198 10 false *B 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
C-3 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
D-3 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

11.RECONFIRM DTC
a.

Connect the speed sensor connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

DTC is output

12.REPLACE REAR SPEED SENSOR
12.REPLACE REAR SPEED SENSOR

Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

END

DTC is output

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY