The EGR system recirculates exhaust gases. The recirculated gas mingles with the intake air so that the EGR system can slow the combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.
In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve angle and the throttle valve angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0400 | Exhaust Gas Recirculation Flow | Mass air flow rate is not changed when turning on the electric EGR control valve assembly while decelerating. (2 trip detection logic) |
·
EGR valve deposit
·
EGR valve passage deposit
·
EGR cooler
·
Mass air flow meter sub-assembly |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0400 |
·
MAF
·
Target EGR Position
·
Actual EGR Valve Pos. |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0400 | After warming up the engine, decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator pedal for approximately 5 seconds). |
If the electric EGR control valve assembly is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
After replacing the fuel supply pump assembly, the ECM needs initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0400 is output | A |
| P0400 and other DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close / Data List / MAF.
| Active Test Display |
|---|
| Activate the EGR Valve Close |
| Data List Display |
|---|
| MAF |
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
When idling the engine, the EGR cooler sub-assembly is bypassed.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close: Off (Open) to On (Closed) |
MAF value does not change | A |
| MAF value changes | B |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (60%) |
·
Atmosphere pressure: 101 kPa
·
Engine coolant temperature: 75°C (167°F) |
3 to 10 gm/sec |
| Closed (0%) | 14 to 23 gm/sec |
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Tester Display |
|---|
| Engine Speed |
| MAF |
Start the engine and read the value when 30 seconds has elapsed.
| Engine speed | MAF |
|---|---|
| Idling | 6 to 30 gm/sec |
| 3000 rpm | 76 to 140 gm/sec |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| EGR Cooler Bypass Position |
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass: Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the EGR cooler sub-assembly is clogged, the mass air flow changes.
If the bypass valve does not mechanically switch even with no clogging in the EGR cooler, the intake air flow will not change.
The bypass valve switch is determined by negative pressure changes and operating sound.
Vacuum inspection.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>ON-VEHICLE INSPECTION
Operating sound inspection.
If the bypass valve does not mechanically switch, perform the repairs listed below and replace the part. Then check for changes in the intake air flow by performing the Active Test again.
No. 2 EGR valve assembly
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>INSPECTION
Vacuum hose connection
Vacuum switching valve assembly (for EGR bypass valve)
A
B
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve, make sure the valve is completely closed.
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of valve shaft, and when wiping off deposits on the EGR control valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR control valve.
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EGR cooler assembly.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR COOLER (w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
When a DTC is output, the mass air flow meter may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| EGR Cooler Bypass Position |
Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass: Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the EGR cooler sub-assembly is clogged, the mass air flow changes.
If the bypass valve does not mechanically switch even with no clogging in the EGR cooler, the intake air flow will not change.
The bypass valve switch is determined by negative pressure changes and operating sound.
Vacuum inspection.
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>ON-VEHICLE INSPECTION
Operating sound inspection.
If the bypass valve does not mechanically switch, perform the repairs listed below and replace the part. Then check for changes in the intake air flow by performing the Active Test again.
No. 2 EGR valve assembly
Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE (w/ DPF)>INSPECTION
Vacuum hose connection
Vacuum switching valve assembly (for EGR bypass valve)
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to the 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
When a DTC is output, the mass air flow meter may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/ DPF)>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT