Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.08
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132956 ENGINE UNIT A

1VD-FTV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 11301M 1.REMOVE CAMSHAFT POSITION SENSOR

a.
A164485

Remove the bolt and camshaft position sensor.


Hide 11301K 2.REMOVE CRANKSHAFT POSITION SENSOR

a.
A164486

Remove the bolt and crankshaft position sensor.


Hide 12263 3.REMOVE NO. 3 VENTILATION HOSE

a.
A381022C01
0.094,0.104 0.604,0.417 0.51,0.313 12 true *A 0.094,2.469 0.49,2.719 0.396,0.25 12 true *B
*A w/ DPF
*B w/o DPF


Slide the 2 clamps and remove the No. 3 ventilation hose from the cylinder head cover sub-assembly LH and ventilation tube sub-assembly.


Hide 12201 4.REMOVE VENTILATION TUBE SUB-ASSEMBLY

a.
A381095

Remove the bolt, union bolt, ventilation tube sub-assembly and gasket.


Hide 16206 5.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A164477

Remove the bolt, union bolt, water by-pass pipe sub-assembly and gasket.


Hide 15620 6.REMOVE OIL FILTER CAP ASSEMBLY WITH OIL FILTER ELEMENT

Hide 15482 7.REMOVE NO. 2 TURBO OIL PIPE

a.
A164475

Remove the 4 bolts, No. 2 turbo oil pipe and gasket.


Hide 15690 8.REMOVE OIL COOLER RELIEF VALVE ASSEMBLY

Hide 15710 9.REMOVE OIL COOLER ASSEMBLY

Hide 15781 10.REMOVE NO. 1 OIL COOLER BRACKET

Hide 12101A 11.REMOVE OIL PAN DRAIN PLUG

a.
A164819

Remove the oil pan drain plug and gasket.


Hide 12102A 12.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 151C1 13.REMOVE SCAVENGING PUMP PIPE

a.
A164493

Remove the 4 bolts, scavenging pump pipe and 2 gaskets.


Hide 15614 14.REMOVE LOWER OIL FILTER ELEMENT COVER

Hide 83530 15.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o Oil Pressure Gauge)

Hide 83520 16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ Oil Pressure Gauge)

Hide 15769 17.REMOVE OIL COOLER PIPE

Hide 12101 18.REMOVE OIL PAN SUB-ASSEMBLY

Hide 11432T 19.REMOVE STRAIGHT SCREW PLUG

HINT:

If water leaks from the straight screw plug or the straight screw plug is corroded, replace the straight screw plug.


A164807C01
0.135,0.281 0.448,0.438 0.313,0.156 10 false *A 0.146,1.854 0.458,2.01 0.313,0.156 10 false *B 0.813,2.01 1.125,2.167 0.313,0.156 10 false B 1.75,0.5 2.063,0.656 0.313,0.156 10 false A 2.198,2.51 2.417,2.646 0.219,0.135 10 true A
*A for Front Side
*B for LH Side


a.

Using a 14 mm hexagon wrench, remove the 2 straight screw plugs and 2 gaskets labeled A.


b.

Using a 10 mm hexagon wrench, remove the straight screw plug and gasket labeled B.


Hide 20.REMOVE STUD BOLT

HINT:

If the stud bolt is deformed or the threads are damaged, replace it.


A164806N01
3.021,2.458 3.177,2.656 0.156,0.198 10 false A 2.115,1.698 2.271,1.896 0.156,0.198 10 true B 0.438,1.979 0.594,2.177 0.156,0.198 10 true A 1.333,0.635 1.521,0.792 0.188,0.156 10 true B

a.

Using an E6 "TORX" wrench, remove the 2 stud bolts labeled A.


b.

Using an E8 "TORX" wrench, remove the 2 stud bolts labeled B.


Hide 15777K 21.REMOVE OIL COOLER HOSE DRAIN COCK ASSEMBLY

HINT:

If the oil cooler hose drain cock assembly is deformed or clogged, replace or repair it.


A164471

a.

Using a 17 mm wrench, remove the oil cooler hose drain cock assembly.


Hide 12121 22.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A164491

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 15403 23.REMOVE OIL PUMP OUTLET PIPE SUB-ASSEMBLY

Hide 15479 24.REMOVE TURBO OIL PIPE FLANGE

a.
A164492

Remove the 2 bolts and turbo oil pipe flange.


Hide 15310H 25.REMOVE OIL REGULATOR ASSEMBLY

Hide 15104 26.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 11381 27.REMOVE ENGINE REAR OIL SEAL RETAINER

Hide 11381A 28.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A164590

Place the engine rear oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the rear crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 15100 29.REMOVE OIL PUMP ASSEMBLY

Hide 151A0 30.REMOVE SCAVENGING PUMP ASSEMBLY

Hide 12108 31.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 12108A 32.REMOVE OIL FILLER CAP GASKET

Hide 23670 33.REMOVE INJECTOR ASSEMBLY RH (w/ DPF)

Hide 11201 34.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/ DPF)

a.
A267294C01
0,0 0,0 false
V100135

Bolt
V100136

Nozzle Holder Clamp Seat


Remove the 19 bolts, 4 nozzle holder clamp seats and cylinder head cover sub-assembly RH.


Hide 11201 35.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/o DPF)

Hide 12270 36.REMOVE OIL SEPARATOR ASSEMBLY

Hide 23670 37.REMOVE INJECTOR ASSEMBLY LH (w/ DPF)

Hide 11202 38.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/ DPF)

a.
A267296C01
0,0 0,0 false
V100135

Bolt
V100136

Nozzle Holder Clamp Seat


Remove the 18 bolts, 4 nozzle holder clamp seats and cylinder head cover sub-assembly LH.


Hide 11202 39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/o DPF)

Hide 11213 40.REMOVE CYLINDER HEAD COVER GASKET

Hide 11229 41.REMOVE NO. 3 CYLINDER HEAD COVER GASKET (w/ DPF)

Hide 11239 42.REMOVE NO. 4 CYLINDER HEAD COVER GASKET (w/ DPF)

Hide 23682A 43.REMOVE NOZZLE HOLDER GASKET RH (w/o DPF)

a.
A174977

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.



Hide 23682B 44.REMOVE NOZZLE HOLDER GASKET LH (w/o DPF)

a.
A174977

Using a small screwdriver and hammer, remove the 4 nozzle holder gaskets.

HINT:

Tape the screwdriver tip before use.



Hide 23681D 45.REMOVE NOZZLE HOLDER SEAL RH (w/o DPF)

Hide 23681E 46.REMOVE NOZZLE HOLDER SEAL LH (w/o DPF)

Hide 23670 47.REMOVE INJECTOR ASSEMBLY RH (w/o DPF)

Hide 23670 48.REMOVE INJECTOR ASSEMBLY LH (w/o DPF)

Hide 15777 49.REMOVE OIL COOLER HOSE

A164838C01
2.198,2.083 2.917,2.083 true 1.219,2.865 2.25,3.25 2.25,3.25 2.417,3.25 true 2.948,2.01 3.26,2.25 0.313,0.24 10 true *1 2.438,3.156 2.75,3.313 0.313,0.156 10 false *2
*1 Oil Cooler Hose
*2 No. 2 Oil Cooler Hose


a.

Slide the 2 clamps and remove the oil cooler hose from the oil cooler pipe and engine water pump assembly.


Hide 15778 50.REMOVE NO. 2 OIL COOLER HOSE

a.

Slide the 2 clamps and disconnect the No. 2 oil cooler hose from the engine water pump assembly and oil pan sub-assembly.


b.

Remove the 2 bolts and No. 2 oil cooler hose.


Hide 16100 51.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 13471 52.REMOVE CRANKSHAFT PULLEY

a.
A163869C01
0.5,4.333 0.5,3.792 true 0.75,2.125 0.75,1.583 true 1.25,3 1.917,3 true 1.958,4.146 1.958,3.604 true 1.104,2.906 1.417,3.063 0.313,0.156 10 false *1 1.875,4.125 2.188,4.281 0.313,0.156 10 false *a 0.615,2.135 1.073,2.333 0.458,0.198 10 false SST 0.365,4.344 0.823,4.542 0.458,0.198 10 false SST
*1 Crankshaft Pulley
*a Protective Tape


Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

To prevent damage to the crankshaft pulley, apply protective tape to the contact areas of SST and the crankshaft pulley before performing this procedure.



b.

Remove the 3 bolts and crankshaft pulley.

NOTICE:

If the crankshaft pulley cannot be removed, temporarily install a bolt to the crankshaft so that the crankshaft pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the crankshaft pulley. Do not tap the crankshaft pulley V-ribbed belt ribs, as the crankshaft may be damaged.



Hide 11302 53.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A164495C01
0.479,2.948 0.792,3.104 0.313,0.156 10 false *1
*1 Nut


Remove the 4 nuts and 16 bolts.


b.

Using a screwdriver, remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly.

HINT:

Tape the screwdriver tip before use.


A316795


c.
A164497

Remove the O-ring from the timing gear case sub-assembly.


Hide 11302A 54.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A158677C01
2.75,0.333 2.583,0.333 2.583,0.333 2.333,1.083 true 2.771,0.25 3.156,0.542 0.385,0.292 10 true *a
*a Wooden Block


Place the timing chain cover sub-assembly on wooden blocks.


b.

Using a screwdriver and wooden block, pry out the front crankshaft oil seal.

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole and crankshaft.


HINT:

Tape the screwdriver tip before use.



Hide 55.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.


b.

Turn the crankshaft clockwise to set the No. 1 cylinder to TDC.


c.

With the crankshaft key 45° counterclockwise from the top position, check that the timing marks of the RH and LH camshaft timing gears are aligned. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks as shown below.

A164815C01
0.5,6.417 0.5,6.25 0.5,6.25 1.052,5.656 true 1.365,4.99 1.635,5.208 0.271,0.219 10 true *a 0.427,6.438 0.698,6.667 0.271,0.229 10 true *1 0.875,5.042 1.125,5.208 0.25,0.167 10 true 45°
*1 Key - -
*a Top - -



d.

Remove the 2 crankshaft pulley set bolts.


Hide 19315 56.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A164507

Using a T30 "TORX" wrench, remove the 2 screws and No. 1 crankshaft position sensor plate.


Hide 13522 57.REMOVE PUMP DRIVE SHAFT GEAR

a.
A164498N01
0.583,0.667 0.75,0.667 0.75,0.667 0.917,1.219 true 0.292,0.573 0.75,0.771 0.458,0.198 10 false SST

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts and pump drive shaft gear.


Hide 13540 58.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A164589

Move the stopper plate clockwise to release the lock, and push the plunger into the No. 1 chain tensioner assembly.


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A164499

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 59.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

A164500

Hide 13561 60.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A164501

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13523 61.REMOVE NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 CHAIN SUB-ASSEMBLY

A164502

Hide 62.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A164589

Move the stopper plate clockwise to release the lock, and push the plunger into the No. 2 chain tensioner assembly.


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A164503

Remove the 2 bolts and No. 2 chain tensioner assembly.


Hide 63.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

A164504

Hide 64.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A164505

Remove the 2 bolts and No. 2 chain vibration damper.


Hide 13529G 65.REMOVE NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 CHAIN SUB-ASSEMBLY

a.
A164506N01
2.25,0.75 2.5,0.167 2.5,0.167 2.667,0.167 true 2.708,0.094 3.167,0.292 0.458,0.198 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts, No. 2 camshaft timing sprocket and No. 2 chain sub-assembly.


Hide 66.REMOVE INJECTION PUMP DRIVE GEAR NUT

a.
A164508N01
0.333,2.917 0.5,2.917 0.5,2.917 1.75,2.198 true 0.052,2.823 0.51,3.021 0.458,0.198 10 false SST

Using SST, hold the No. 1 idle gear.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the injection pump drive gear nut.


Hide 13525 67.REMOVE NO. 1 IDLE GEAR

a.
A164510

Remove the 2 bolts, idle gear thrust plate and No. 1 idle gear.


Hide 13581 68.REMOVE NO. 1 IDLE GEAR SHAFT

A164511

Hide 13613 69.REMOVE INJECTION PUMP DRIVE GEAR

a.
A164509N01
0.583,1.833 0.75,1.833 0.75,1.833 1.25,1.333 true 0.302,1.74 0.76,1.938 0.458,0.198 10 false SST

Using SST, remove the injection pump drive gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)


Hide 70.INSPECT RADIAL BALL BEARING

a.
A164845

Turn the radial ball bearing, and check that the radial ball bearing moves smoothly and quietly.

If it moves roughly or noisily, replace the radial ball bearing.


Hide 71.REMOVE RADIAL BALL BEARING

HINT:

It is not necessary to remove the radial ball bearing unless it is being replaced.


a.
A158678N01
0.583,1 1.333,1 true 0.302,0.906 0.76,1.104 0.458,0.198 10 false SST

Using SST, remove the radial ball bearing.

SST
09950-00020  
09950-00030  
09950-60010  (09951-00580)
09950-40011  (09957-04010)


Hide 13616 72.SEPARATE INJECTION PUMP DRIVE GEAR AND INJECTION PUMP SHAFT SPROCKET SUB-ASSEMBLY

a.
A158679

Hold the injection pump shaft sprocket sub-assembly in a vise between aluminum plates.


b.

Remove the 4 bolts and separate the injection pump drive gear and injection pump shaft sprocket sub-assembly.


Hide 73.REMOVE STRAIGHT PIN

HINT:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A158649

Remove the straight pin.


Hide 11248 75.REMOVE V-BANK SILENCER

A164488

Hide 11301 76.REMOVE TIMING GEAR CASE SUB-ASSEMBLY

a.
A164875C01
1.125,2.844 1.438,3 0.313,0.156 10 false *1 2.135,2.854 2.448,3.01 0.313,0.156 10 false *1
*1 Nut


Remove the 22 bolts, 2 nuts and timing gear case sub-assembly shown in the illustration.


b.
A164513

Remove the 2 O-rings and timing gear case sub-assembly gasket.


Hide 25707 77.REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A164514

Remove the 3 bolts and No. 2 vacuum transmitting pipe sub-assembly.


Hide 78.REMOVE STUD BOLT

HINT:

If the stud bolt is deformed or the threads are damaged, replace it.


a.

Using an E7 "TORX" wrench, remove the 4 stud bolts labeled A.


b.

Remove the 2 stud bolts labeled B.

A164836C01
0.156,0.229 0.469,0.385 0.313,0.156 10 false *A 3.75,0.229 4.063,0.385 0.313,0.156 10 false *B 2.875,0.813 3.031,1.01 0.156,0.198 10 false A 6.406,1.188 6.563,1.385 0.156,0.198 10 false B 0.677,1.063 0.833,1.26 0.156,0.198 10 true A 0.969,1.281 1.125,1.479 0.156,0.198 10 true A 1.24,1.26 1.396,1.458 0.156,0.198 10 true A 1.781,2.094 1.938,2.292 0.156,0.198 10 true A 4.427,1.521 4.594,1.708 0.167,0.188 10 true B 4.844,1.771 5.01,1.958 0.167,0.188 10 true B
*A for Front Side *B for Rear Side



Hide 13511 79.REMOVE NO. 1 AND NO. 2 CAMSHAFTS

a.
A164905

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.


b.
A164787

Loosen the 2 union bolts.


c.
A164788N01
1.771,1.281 2.083,1.479 0.313,0.198 10 true 20 1.406,1.865 1.719,2.063 0.313,0.198 10 true 19 1.76,0.917 2.073,1.115 0.313,0.198 10 true 18 1.406,0.354 1.708,0.49 0.302,0.135 10 true 17 2.375,1.281 2.688,1.479 0.313,0.198 10 true 16 2.01,1.854 2.323,2.052 0.313,0.198 10 true 15 2.375,0.917 2.688,1.115 0.313,0.198 10 true 14 2.031,0.354 2.313,0.5 0.281,0.146 10 true 13 1.156,1.271 1.469,1.469 0.313,0.198 10 true 12 0.813,1.865 1.125,2.063 0.313,0.198 10 true 11 1.135,0.917 1.448,1.115 0.313,0.198 10 true 10 0.833,0.344 1.021,0.49 0.188,0.146 10 true 9 2.99,1.281 3.156,1.448 0.167,0.167 10 true 8 2.99,1.51 3.146,1.708 0.156,0.198 10 true 7 3,0.906 3.198,1.094 0.198,0.188 10 true 6 3.021,0.667 3.198,0.823 0.177,0.156 10 true 5 0.271,1.385 0.396,1.573 0.125,0.188 10 true 4 0.396,1.906 0.51,2.104 0.115,0.198 10 true 3 0.24,0.76 0.365,0.948 0.125,0.188 10 true 2 0.292,0.323 0.427,0.5 0.135,0.177 10 true 1

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


d.
A164789

Remove the 2 union bolts and No. 1 and No. 2 oil feed pipe sub-assemblies.


e.
A164790

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



f.

Remove the No. 1 and No. 2 camshafts.


Hide 80.REMOVE NO. 2 CAMSHAFT BEARING CAP

A164530

Hide 81.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Replace the ring pin.

Standard protrusion:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


A316796C01
0.938,0.292 1.25,0.448 0.313,0.156 10 false *1 0.938,1.542 1.25,1.698 0.313,0.156 10 false *a 6.083,1.646 6.396,1.802 0.313,0.156 10 false *b
*1 No. 2 Camshaft Bearing Cap - -
*a Cylinder Head Sub-assembly RH Side *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)



Hide 13801 82.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies.


Hide 13750 83.REMOVE NO. 1 VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 No. 1 valve lash adjuster assemblies.


Hide 13053 86.REMOVE NO. 3 AND NO. 4 CAMSHAFTS

a.
A164905

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.


b.
A164783

Loosen the 2 union bolts.


c.
A164784N01
1.875,1.26 2.135,1.417 0.26,0.156 10 true 20 1.521,1.833 1.833,2.031 0.313,0.198 10 true 19 1.844,0.896 2.104,1.052 0.26,0.156 10 true 18 1.51,0.302 1.771,0.458 0.26,0.156 10 true 17 2.479,1.25 2.719,1.406 0.24,0.156 10 true 16 2.146,1.833 2.458,2.031 0.313,0.198 10 false 15 2.479,0.885 2.719,1.042 0.24,0.156 10 true 14 2.156,0.292 2.406,0.438 0.25,0.146 10 true 13 1.25,1.26 1.448,1.417 0.198,0.156 10 true 12 0.896,1.833 1.208,2.031 0.313,0.198 10 false 11 1.24,0.885 1.458,1.083 0.219,0.198 10 true 10 0.156,0.281 0.469,0.479 0.313,0.198 10 false 1 0.146,0.781 0.25,0.948 0.104,0.167 10 true 2 0.26,1.896 0.573,2.094 0.313,0.198 10 false 3 0.156,1.354 0.26,1.521 0.104,0.167 10 true 4 3.146,0.635 3.354,0.792 0.208,0.156 10 true 5 3.135,0.896 3.313,1.063 0.177,0.167 10 true 6 3.104,1.5 3.323,1.667 0.219,0.167 10 true 7 3.115,1.271 3.323,1.427 0.208,0.156 10 true 8 0.917,0.302 1.083,0.448 0.167,0.146 10 true 9

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


d.
A164785

Remove the 2 union bolts and No. 3 and No. 4 oil feed pipe sub-assemblies.


e.
A164786

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



f.

Remove the No. 3 and No. 4 camshafts.


Hide 87.REMOVE NO. 5 CAMSHAFT BEARING CAP

A164538

Hide 88.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Replace the ring pin.

Standard protrusion:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


A316796C01
0.938,0.292 1.25,0.448 0.313,0.156 10 false *1 0.938,1.542 1.25,1.698 0.313,0.156 10 false *a 6.083,1.646 6.396,1.802 0.313,0.156 10 false *b
*1 No. 5 Camshaft Bearing Cap - -
*a Cylinder Head Sub-assembly LH Side *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)



Hide 89.REMOVE NO. 2 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 2 valve rocker arm sub-assemblies.


Hide 90.REMOVE NO. 2 VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 No. 2 valve lash adjuster assemblies.