77011 1.INSTALL LOWER FUEL TANK FILLER PIPE SUB-ASSEMBLY
Install a new gasket and the lower fuel tank filler pipe sub-assembly with the 6 screws.
2.INSTALL FUEL SENDER GAUGE ASSEMBLY
77420 3.INSTALL NO. 2 FUEL CUT OFF VALVE ASSEMBLY
Install the No. 2 fuel cut off valve assembly onto the fuel tank assembly.
77380 4.INSTALL FUEL CUT OFF VALVE ASSEMBLY
Install the fuel cut off valve assembly onto the fuel tank assembly.
77026A 5.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Install 2 new gaskets and the No. 1 evaporation tube sub-assembly to the fuel tank assembly with the 8 screws and 2 nuts.
w/o DPF:
| *a | Screw |
| *b | Nut |
Install 2 new gaskets and the No. 1 evaporation tube sub-assembly to the fuel tank assembly with the 8 screws and 2 nuts.
Attach the clamp.
w/ DPF:
Install 2 new gaskets and the No. 1 evaporation tube sub-assembly to the fuel tank assembly with the 8 screws.
Attach the clamp.
6.INSTALL FUEL SUCTION TUBE ASSEMBLY
w/o DPF:
Install a new gasket and the fuel suction tube assembly with the 5 screws.
w/ DPF:
| *a | Screw |
| *b | Nut |
Install a new gasket and the fuel suction tube assembly with the 5 screws 2 nuts.
Attach the clamp.
77100 7.INSTALL FUEL TANK ASSEMBLY
Set the fuel tank assembly and fuel tank protector on an engine lifter.
Raise the engine lifter.
Connect the 2 fuel tank bands with the 2 bolts.
Connect the fuel sender gauge connector.
77100D 8.CONNECT FUEL BREATHER HOSE
w/o DPF:
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
Connect the fuel breather hose to the fuel tank assembly, and slide the hose clip to secure the hose.
Install the fuel breather hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
w/ DPF:
Connect the fuel breather hose to the fuel tank assembly, and slide the hose clip to secure the hose.
Install the fuel breather hose as shown in the illustration.
| *a | Hose Clip | *b | Fuel Breather Hose |
| *c | Upper | *d | Front |
| *e | Fuel Tank Assembly | - | - |
77213 9.CONNECT INLET FUEL HOSE
w/o DPF:
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
Connect the inlet fuel hose to the lower fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.
Install the inlet fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the clamps so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
w/ DPF:
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
Connect the inlet fuel hose to the lower fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.
Install the inlet fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the clamps so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
10.CONNECT FUEL RETURN HOSE
w/o DPF:
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
Connect the fuel return hose to the fuel suction tube assembly, and slide the hose clip to secure the hose.
Install the fuel return hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
w/ DPF:
Connect the fuel return hose to the fuel suction tube assembly, and slide the hose clip to secure the hose.
Install the fuel return hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clip as shown in the illustration.
| *a | Hose Clip | *b | Fuel Return Hose |
| *c | Fuel Suction Tube Assembly | *d | Upper |
| *e | RH Side | *f | Paint |
| *g | Paint Center | *h | 0 to 3.0 mm (0 to 0.118 in.) |
| *i | 2.0 to 7.0 mm (0.0787 to 0.275 in.) | - | - |
11.CONNECT FUEL MAIN HOSE
w/o DPF:
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
Connect the fuel main hose to the fuel suction tube assembly, and slide the hose clip to secure the hose.
Install the fuel main hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
w/ DPF:
Connect the fuel main hose to the fuel suction tube assembly, and slide the hose clip to secure the hose.
Install the fuel main hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clip as shown in the illustration.
| *a | Hose Clip | *b | Fuel Return Hose |
| *c | Fuel Suction Tube Assembly | *d | Upper |
| *e | RH Side | *f | Paint |
| *g | Paint Center | *h | 0 to 3.0 mm (0 to 0.118 in.) |
| *i | 2.0 to 7.0 mm (0.0787 to 0.275 in.) | - | - |
77207B 12.INSTALL NO. 3 FUEL MAIN TUBE SUB-ASSEMBLY
| *a | Bolt |
| *b | Fuel Hose |
| *c | Hose Clip |
| *d | Upper |
| *e | 0 to 3.0 mm (0 to 0.118 in.) |
| *f | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
for Single Tank Type, w/o DPF:
Install the No. 3 fuel main tube sub-assembly with the 2 bolts.
Connect the fuel hoses to the No. 3 fuel main tube sub-assembly, and slide the hose clip to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clip so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clip as shown in the illustration.
| *a | Bolt |
| *b | Fuel Hose |
| *c | Hose Clip |
| *d | Upper |
| *e | LH Side |
| *f | 0 to 3.0 mm (0 to 0.118 in.) |
| *g | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
for Double Tank Type, w/o DPF:
Install the fuel No. 3 main tube sub-assembly with the 2 bolts.
Connect the fuel hoses to the No. 3 fuel main tube sub-assembly, and slide the hose clips to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clips so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clips as shown in the illustration.
w/ DPF:
Install the fuel No. 3 main tube sub-assembly with the 3 bolts.
Connect the fuel hoses to the No. 3 fuel main tube sub-assembly, and slide the hose clips to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clips so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clips as shown in the illustration.
| *a | Bolt | *b | Fuel Hose |
| *c | Hose Clip | *d | Upper |
| *e | RH Side | *f | 0 to 3.0 mm (0 to 0.118 in.) |
| *g | 2.0 to 7.0 mm (0.0787 to 0.275 in.) | - | - |
77206C 13.CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY
for Single Tank Type, w/o DPF:
Connect the No. 2 fuel main tube sub-assembly to the fuel tube clamps.
Connect the fuel hoses to the No. 2 fuel main tube sub-assembly, and slide the hose clips to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clips so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Install the hose clips as shown in the illustration.
Connect the No. 2 fuel main tube sub-assembly with the 3 bolts.
| *a | Fuel Tube Clamp | *b | Fuel Hose |
| *c | Hose Clip | *d | Upper |
| *e | 0 to 3.0 mm (0 to 0.118 in.) | *f | 2.0 to 7.0 mm (0.0787 to 0.275 in.) |
| *g | Bolt | - | - |
for Double Tank Type, w/o DPF:
Connect the No. 2 fuel tube sub-assembly to the fuel tube clamps.
Connect the fuel hoses to the No. 2 fuel main tube sub-assembly, and slide the hose clips to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clips so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Connect the No. 2 fuel main tube sub-assembly with the 3 bolts.
| *a | Fuel Tube Clamp | *b | Fuel Hose |
| *c | Hose Clip | *d | 0 to 3.0 mm (0 to 0.118 in.) |
| *e | 2.0 to 7.0 mm (0.0787 to 0.275 in.) | *f | Bolt |
w/ DPF:
Connect the No. 2 fuel tube sub-assembly to the fuel tube clamps.
Connect the fuel hoses to the No. 2 fuel main tube sub-assembly, and slide the hose clips to secure the hoses.
Install the fuel hose with a gap of 0 to 3.0 mm (0 to 0.118 in.) between the hose and stopper.
Install the hose clips so that they are 2.0 to 7.0 mm (0.0787 to 0.275 in.) from the end of the hose.
Connect the No. 2 fuel main tube sub-assembly with the 3 bolts.
| *a | Fuel Tube Clamp | *b | Fuel Hose |
| *c | Hose Clip | *d | Front |
| *e | LH Side | *f | 0 to 3.0 mm (0 to 0.118 in.) |
| *g | 2.0 to 7.0 mm (0.0787 to 0.275 in.) | *h | No. 1 Fuel Tube Protector Support |
| *i | Bolt | - | - |
77296B 14.INSTALL NO. 1 FUEL TUBE PROTECTOR SUPPORT (w/ DPF)
Attach the 4 claws to install the No. 1 fuel tube protector support.
15.INSTALL FUEL TUBE PROTECTOR
Install the fuel tube protector with the 4 bolts.
16.INSTALL MANUAL TRANSMISSION WITH TRANSFER (w/ DPF)
37110 17.INSTALL PROPELLER SHAFT ASSEMBLY (w/o DPF)
18.INSTALL EXHAUST PIPE (w/o DPF)
for 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (for 5 Door)>INSTALLATION
except 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>INSTALLATION
19.BLEED AIR FROM FUEL SYSTEM
20.INSPECT FOR FUEL LEAK