31236B 1.INSTALL RELEASE FORK SUPPORT
31237 2.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT
31204 3.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY
4.INSTALL EXHAUST PIPE SUPPORT
Install the exhaust pipe support with the 2 bolts.
5.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 4 wire harness clamp brackets with the 4 bolts.
6.INSTALL TRANSFER ASSEMBLY
7.INSTALL DIFFERENTIAL PRESSURE SENSOR
8.INSTALL MANUAL TRANSMISSION WITH TRANSFER
Install the manual transmission with transfer with the 10 bolts.
9.CONNECT WIRE HARNESS
Connect the 16 wire harness clamps and 3 wire harness connectors to the manual transmission with transfer.
Tilt up the manual transmission with transfer.
10.CONNECT GROUND CABLE
Connect the ground cable with the bolt.
12371 11.INSTALL REAR ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator to the manual transmission with transfer with the 4 bolts.
51203 12.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
except Single Cab:
Install the No. 2 frame crossmember sub-assembly with the 2 nuts.
Install the 8 bolts.
for Single Cab:
Install the No. 2 frame crossmember sub-assembly with the 2 nuts.
Install the 4 bolts and 4 nuts.
12140 13.INSTALL OIL PAN COVER
Install the oil pan cover with the 2 bolts.
14.INSTALL FRONT STABILIZER BRACKET LH
Install the front stabilizer bracket LH with the 2 bolts.
15.INSTALL FRONT STABILIZER BRACKET RH
Use the same procedure described for the LH side.
31470 16.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
Install the clutch release cylinder assembly with the 2 bolts.
37110 17.INSTALL REAR PROPELLER SHAFT ASSEMBLY
37140 18.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
51447C 19.INSTALL TRANSFER CASE PROTECTOR
Install the transfer case protector to the No. 2 frame crossmember sub-assembly with the 3 bolts.
20.ADD MANUAL TRANSMISSION OIL
36308 21.CONNECT HIGH AND LOW SHIFT ROD SUB-ASSEMBLY
Connect the high and low shift rod sub-assembly with the washer and nut.
22.INSTALL TRANSFER SHIFT LEVER ASSEMBLY
23.INSPECT AND ADJUST TRANSFER SHIFT LEVER ASSEMBLY
33530F 24.INSTALL TRANSMISSION SHIFT LEVER ASSEMBLY
| *1 | Shift Lever Cap |
|
Press Down |
|
Clockwise |
|
Lock |
Cover the transmission shift lever cap with a cloth or equivalent.
While pressing down on the transmission shift lever cap, turn it clockwise to install the transmission shift lever.
Attach the shift lever cap boot.
58286 25.INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT
36303 26.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
89441A 27.INSTALL DECELERATION SENSOR
89170 28.INSTALL AIRBAG SENSOR ASSEMBLY WITH AIRBAG SENSOR BRACKET
89179A 29.INSTALL AIRBAG SENSOR COVER
58811B 30.INSTALL CONSOLE BOX
58191 31.INSTALL FRONT FLOOR FOOTREST (except Pickup)
62112A 32.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Single Cab)>INSTALLATION
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>INSTALLATION
62111A 33.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
67914 34.INSTALL FRONT DOOR SCUFF PLATE LH
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Single Cab)>INSTALLATION
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>INSTALLATION
67913 35.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
87240H 36.INSTALL HEATER WATER VALVE ASSEMBLY
Install the heater water valve assembly to the vehicle with the bolt.
Connect the 2 hoses to the heater water valve assembly and slide the 2 clamps to secure the hoses.
Connect the cable to the heater water valve assembly.
16371 37.INSTALL FAN PULLEY
16711 38.INSTALL FAN SHROUD
16470 39.INSTALL RADIATOR RESERVOIR ASSEMBLY
17875 40.INSTALL INTAKE AIR CONNECTOR PIPE
17805 41.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY
42.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17705 43.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17881 44.INSTALL NO. 1 AIR CLEANER HOSE
16571C 45.INSTALL NO. 1 RADIATOR HOSE
46.INSTALL EXHAUST PIPE ASSEMBLY
for 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (for 5 Door)>INSTALLATION
except 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>INSTALLATION
47.ADD ENGINE COOLANT
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
49.PERFORM DIAGNOSTIC SYSTEM CHECK
50.CHECK SRS WARNING LIGHT
51.INSPECT FOR ENGINE COOLANT LEAK
52.INSPECT FOR EXHAUST GAS LEAK
51442 53.INSTALL NO. 2 ENGINE UNDER COVER