Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  Black Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbocharger and intake manifold


Data List MAP

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug

·

Check the glow plug indicator light



Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Injector
Main fault Blockage, increase in fuel injection volume
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



HINT:
·

When the sliding resistance of the internal parts of the injector assemblies has increased due to internal contamination, injection quantity will increase at high Fuel Press due to a delay in fuel injector closure.

·

When black smoke occurs due to contamination of the injector assemblies, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficulty starting, etc., which are also present when the Fuel Press is low.



Injector Driver
Main fault Circuit fault: The fuel injector does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as fuel injector
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List Actual Throttle Position, Actual Throttle Position #2
·

100%: Fully closed

·

0%: Fully open

·

When the ignition switch to ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Black Smoke


·

Engine Speed

·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Engine Speed of Cyl #1 (to #8)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #8)

·

Injection Volume

·

Actual Throttle Position

·

Actual Throttle Position #2



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing a fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


Explanation of Symptom


Black Smoke The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions.
When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by MAF).
Black smoke is emitted when either: 1) a lack of oxygen is present during combustion, or 2) too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich.


PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B


HINT:

If only DTC P1609 is output, proceed to step 2.




A

2.CHECK FOR BLACK SMOKE

B

2.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times or more.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:
·

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.

·

If the procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.




Result:
Proceed to
OK
NG



OK

3.RECOVERY TO NORMAL

NG

4.CHECK INTAKE SYSTEM
3.RECOVERY TO NORMAL
HINT:

If the racing procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.


Result:
Proceed to
NEXT



NEXT

END

4.CHECK INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

HINT:
·

Make sure that the air cleaner is not clogged and the intake and exhaust system hoses are not disconnected.

·

When the vacuum hoses are disconnected.

·

Check that the intercooler is not clogged with foreign matter.

·

Check that there are no disconnected, pinched or leaking hoses or pipes.

·

Check that there are no modifications made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of common rail system components.

OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

6.CHECK INJECTOR COMPENSATION CODE

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

OK:

Compensation codes stored in the ECM match the compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

7.CHECK FOR BLACK SMOKE

NG

17.REGISTER INJECTOR COMPENSATION CODE
7.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

8.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)

OK

END

8.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Black Smoke.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the GTS to a PC. Intelligent Viewer must be installed on the PC.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

9.READ VALUE USING GTS (MAF AND MAP)
9.READ VALUE USING GTS (MAF AND MAP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (the engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
MAP
50003 61 319,314

e.

Take a snapshot when the engine speed is maintained at 3000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

Result:
Result Proceed to
MAF 68 gm/sec or more and MAP 110 kPa or higher A
Except above B


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under the standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. The standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, the pressure drops by 1 kPa. This varies by weather.





A

10.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)

B

37.READ VALUE USING GTS (MAF)
10.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #8)
a.

Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute.

Result:
Result Proceed to
Injection Volume is less than 5.5 mm3/st at 3000 rpm A
Injection Feedback Val for at least one cylinder is more than +3 mm3/st B
Except above C




A

11.REPLACE FUEL INJECTOR OF ALL CYLINDER

B

12.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

20.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
11.REPLACE FUEL INJECTOR OF ALL CYLINDER
a.

Replace the fuel injector.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
12.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.


d.

Check the engine speed during the Active Test.

Powertrain > Engine and ECT > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine Speed of Cyl #5
Engine Speed of Cyl #6
Engine Speed of Cyl #7
Engine Speed of Cyl #8
50004 61 111 492,493,494,495,496,497,498,499
Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #8 are within 10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

13.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
13.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

14.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
a.

Replace the fuel injector of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

17.REGISTER INJECTOR COMPENSATION CODE
17.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 61 148

Result:
Proceed to
NEXT



NEXT

18.CHECK FOR BLACK SMOKE
18.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
20.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
MAP
50003 61 64,314

d.

Compare MAP to Atmosphere Pressure when the ignition switch to ON (the engine is stopped).

HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa (0.1 kgf/cm2, 1.5 psi) or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

The standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, the pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather (high atmospheric pressure, low atmospheric pressure).



Result:
Result Proceed to
MAP and Atmosphere Pressure have same value A
Atmosphere Pressure is different from actual atmospheric pressure B
MAP is different from actual atmospheric pressure C




A

21.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

24.REPLACE ECM

C

27.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
21.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine and ECT > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 706,54

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E62
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.406,2.594 5.01,2.417 5.01,2.417 5.073,2.417 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 0.167,1.427 1.531,1.583 1.365,0.156 10 false Active Test Operation 0.521,0.594 1.917,0.792 1.396,0.198 10 false Engine Speed 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Press 3.646,2.01 5,2.177 1.354,0.167 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.865,2.792 0.74,0.365 10 false Less than 10000 kPa 3,4.271 3.698,4.5 0.698,0.229 10 false 2 seconds 5.135,2.354 6,2.885 0.865,0.531 10 false Abnormal Fuel Pressure 2.448,1.156 3.125,1.354 0.677,0.198 10 false Test Start 4.177,1.146 4.844,1.344 0.667,0.198 10 false Test Stop 5.625,1.156 6.302,1.354 0.677,0.198 10 false Test Start 2.208,1.823 2.99,2.156 0.781,0.333 10 false Normal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure in the common rail assembly.




Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

NG

28.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
22.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309
OK:

Coolant Temp is the same as the ambient temperature.


HINT:

When the engine coolant temperature is low even though the engine has been fully warmed up, or when the engine coolant temperature is high even though the engine is cold, inspect the sensor.



Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))

NG

25.CHECK AND REPLACE COOLANT TEMPERATURE SENSOR
23.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).

OK:

Intake Air is the same as Intake Air Temp (Turbo).


Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 61 318,240

Result:
Proceed to
OK
NG



OK

35.CHECK FOR BLACK SMOKE

NG

26.CHECK AND REPLACE MALFUNCTIONING PARTS
24.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
25.CHECK AND REPLACE COOLANT TEMPERATURE SENSOR
a.

b.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
26.CHECK AND REPLACE MALFUNCTIONING PARTS

b.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


c.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/o DPF)>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



d.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
27.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
28.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r2-1 (+B) - C39-106 (PCV+) Always Below 1 Ω
r2-2 (PCV) - C39-105 (PCV-) Always Below 1 Ω
r2-1 (+B) or C39-106 (PCV+) - Body ground and other terminals Always 10 kΩ or higher
r2-2 (PCV) or C39-105 (PCV-) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

29.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY

NG

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
29.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the fuel supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.

OK:

Fuel is properly supplied to the fuel supply pump assembly when the priming pump is operated.


HINT:
·

When there is a lack of fuel, the fuel pressure drops.

·

Inspect for fuel filter clogging (Check that the fuel filter is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

30.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
30.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

31.BLEED AIR FROM FUEL SYSTEM
31.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

32.PERFORM FUEL SUPPLY PUMP INITIALIZATION
32.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP ASSEMBLY)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

34.BLEED AIR FROM FUEL SYSTEM
34.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
35.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
37.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Engine speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
50003 61 315,319

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine speed MAF
Idling 6.1 to 26.5 gm/sec
3000 rpm 68 to 170 gm/sec



Result:
Proceed to
OK
NG



OK

18.CHECK FOR BLACK SMOKE

NG

38.REPLACE MASS AIR FLOW METER
38.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER(w/o DPF)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

18.CHECK FOR BLACK SMOKE