Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM C

1VD-FTV ENGINE CONTROL  ECD SYSTEM  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

The fuel pressure sensor mounted on the common rail assembly converts the fuel pressure inside the common rail assembly into an electrical signal and outputs the signal to the ECM. The ECM controls the fuel supply pump assembly in order to maintain the fuel pressure inside the common rail assembly at a target pressure calculated by the ECM. Refer to System Description (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

HINT:
·

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093.

·

If P0093 is present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0093 Fuel System Leak Detected - Large Leak Fuel pressure drop before and after the fuel injection is larger than the threshold a certain number of times (0.2 seconds or more).
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each fuel injector

·

Suction control valve (fuel supply pump assembly)

·

Fuel injector

·

Pressure limiter (common rail assembly LH)

·

Fuel pressure sensor (common rail assembly RH)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in fuel injector circuit

·

No. 1 or No. 2 injector driver (P062D, P062E stored simultaneously)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0093
·

Fuel Press

·

Target Common Rail Pressure



HINT:

When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.


Reference:
Engine Speed Fuel Press
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0093 After idling for 60 seconds, run the engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.

MONITOR DESCRIPTION

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail assembly after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping.

The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, both fuel injection and fuel supply pump assembly operation are suspended, and then the engine is stopped. Before the engine is stopped, the ECM permits the vehicle to be driven for 1 minute. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an fuel injector, the ECM needs registration (Click here Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, fuel injector, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs and freeze frame data.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
P0093 and "P0190, P0192 and/or P0193" are output C
P0093 and "P0335 and/or P0339" are output B
Except above A




A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO DTC CHART (CRANKSHAFT POSITION SENSOR CIRCUIT)

C

GO TO FUEL PRESSURE SENSOR CIRCUIT

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B




A

4.ADD FUEL

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)
4.ADD FUEL
a.

Add fuel.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.
A223284

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump assembly inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the Fuel Press does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

Even if air bleeding completes with the priming pump, the vehicle may take 10 seconds or more to start.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

g.

Start the engine. (*A)


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak. (*B)


i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)

Powertrain > Engine and ECT > Active Test
Tester Display
Test the Fuel Leak
50004 61 90

j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


l.

Read Current DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps (*A) to (*D).


n.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)


s.

Repeat procedures (*E) and (*F) 5 times.

A220593E08
1.656,1.844 2.042,2.021 0.385,0.177 10 false 5000 1.51,0.583 2.01,0.76 0.5,0.177 10 false 160000 5.135,2.125 5.771,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.823 1.021,1.073 0.948,0.25 10 false Fuel Pressure 0.083,2.167 1.01,2.438 0.927,0.271 10 false Engine Speed 0.083,3.458 1.25,3.656 1.167,0.198 10 false Accelerator Pedal 0.948,3.083 2.115,3.281 1.167,0.198 10 false Fully Depressed 1.021,3.719 2,3.917 0.979,0.198 10 false Fully Released 2.875,4.24 3.573,4.427 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.958 3.729,3.198 0.625,0.24 10 false Step (*E) 6.208,2.948 6.813,3.188 0.604,0.24 10 false Step (*E) 4.75,2.958 5.375,3.198 0.625,0.24 10 false Step (*F) 2.104,0.573 2.375,0.76 0.271,0.188 10 false kPa 2.073,1.771 2.385,1.938 0.313,0.167 10 false rpm


t.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


u.

Read Current DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
DTC is output A
No DTC is output B




A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)
a.

Read the value of Injection Feedback Val #1 to #8 in the freeze frame data recorded in Procedure 2.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A


HINT:

When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.




A

7.READ VALUE USING GTS (FUEL PRESS)

B

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
7.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

e.

Start the engine.


f.

Read the value of Fuel Press while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A




A

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)

B

14.INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 61 368,369,370,371,372,373,374,375

e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large B
Except above A


HINT:
·

When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result:
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B




A

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY

B

18.READ VALUE USING GTS (ENGINE SPEED)
10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine and ECT > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 706,54

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E62
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.406,2.594 5.01,2.417 5.01,2.417 5.073,2.417 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 0.167,1.427 1.531,1.583 1.365,0.156 10 false Active Test Operation 0.521,0.594 1.917,0.792 1.396,0.198 10 false Engine Speed 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Press 3.646,2.01 5,2.177 1.354,0.167 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.865,2.792 0.74,0.365 10 false Less than 10000 kPa 3,4.271 3.698,4.5 0.698,0.229 10 false 2 seconds 5.135,2.354 6,2.885 0.865,0.531 10 false Abnormal Fuel Pressure 2.448,1.156 3.125,1.354 0.677,0.198 10 false Test Start 4.177,1.146 4.844,1.344 0.667,0.198 10 false Test Stop 5.625,1.156 6.302,1.354 0.677,0.198 10 false Test Start 2.208,1.823 2.99,2.156 0.781,0.333 10 false Normal Fuel Pressure

Standard:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B




A

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

14.INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM)
13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231
HINT:
·

If the engine idle speed does not change when an fuel injector is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

15.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
14.INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug for all the cylinders.

Click hereEngine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an fuel injector.

·

After replacing an fuel injector, make sure that the Fuel Press (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.





Result:
Proceed to
NEXT



NEXT

15.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
15.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
a.

Replace the fuel injector of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the Repair Manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.




Result:
Proceed to
NEXT



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

17.REGISTER INJECTOR COMPENSATION CODE
17.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 61 148

Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
18.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 61 315

d.

Read the value while cranking and idling the engine.

Standard:
GTS Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine 500 to 600 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the GTS.



Result:
Proceed to
OK
NG



OK

19.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)

NG

28.REPLACE CRANKSHAFT POSITION SENSOR
19.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.


A391015C01
1.813,1.094 2.26,0.594 2.26,0.594 2.344,0.594 true 2.604,2.323 2.531,2.323 2.531,2.323 1.729,1.5 true 0.969,0.458 1.281,0.615 0.313,0.156 10 false *1 2.635,2.24 2.948,2.396 0.313,0.156 10 false *2 2.385,0.51 2.698,0.667 0.313,0.156 10 false *3 3.74,1.406 4.052,1.563 0.313,0.156 10 false *4 5.802,1.167 6.115,1.323 0.313,0.156 10 false *5 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly RH (Fuel Pressure Sensor) *4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


Result:
Result Proceed to
MIL does not come on A
MIL comes on B



A

20.INSPECT FUEL TEMPERATURE SENSOR

B

24.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
20.INSPECT FUEL TEMPERATURE SENSOR
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

OK:

The value is almost the same as the actual fuel temperature.


HINT:
·

When the engine is stopped and left overnight, the fuel temperature becomes the same as the ambient temperature.

·

If there is a problem with the fuel temperature sensor, and a fuel temperature value lower than the actual fuel temperature is indicated, P0093 may be stored.




Result:
Proceed to
OK
NG



OK

21.CHECK FOR INTERMITTENT PROBLEMS

NG

23.REPLACE FUEL TEMPERATURE SENSOR
21.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)


j.

Repeat procedures (*A) and (*B) 5 times.

A220593E48
1.635,1.813 2.021,1.99 0.385,0.177 10 false 3800 1.469,0.542 1.969,0.719 0.5,0.177 10 false 200000 5.135,2.083 5.771,2.26 0.635,0.177 10 false 3000 rpm 1.865,2.5 1.99,2.677 0.125,0.177 10 false 0 1.854,1.167 1.979,1.344 0.125,0.177 10 false 0 0.063,0.781 1.552,0.948 1.49,0.167 10 false Fuel Press 0.063,2.125 1.042,2.365 0.979,0.24 10 false Engine Speed 0.063,3.385 1.229,3.552 1.167,0.167 10 false Accelerator Pedal 0.948,3.042 2.115,3.24 1.167,0.198 10 false Fully Depressed 1.021,3.688 2,3.885 0.979,0.198 10 false Fully Released 2.854,4.177 3.552,4.365 0.698,0.188 10 false 5 seconds 6.448,4.094 6.854,4.281 0.406,0.188 10 false Time 3.104,2.917 3.729,3.156 0.625,0.24 10 false Step (*A) 6.208,2.917 6.802,3.156 0.594,0.24 10 false Step (*A) 4.75,2.917 5.375,3.156 0.625,0.24 10 false Step (*B) 2.104,0.531 2.375,0.719 0.271,0.188 10 false kPa 2.073,1.719 2.385,1.885 0.313,0.167 10 false rpm


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes


l.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
OK:

No DTCs are output.



Result:
Proceed to
NEXT



NEXT

END

23.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL

HINT:

Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
24.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

25.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
25.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.


A391015C01
1.813,1.094 2.26,0.594 2.26,0.594 2.344,0.594 true 2.604,2.323 2.531,2.323 2.531,2.323 1.729,1.5 true 0.969,0.458 1.281,0.615 0.313,0.156 10 false *1 2.635,2.24 2.948,2.396 0.313,0.156 10 false *2 2.385,0.51 2.698,0.667 0.313,0.156 10 false *3 3.74,1.406 4.052,1.563 0.313,0.156 10 false *4 5.802,1.167 6.115,1.323 0.313,0.156 10 false *5 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly RH (Fuel Pressure Sensor) *4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


Result:
Result Proceed to
MIL does not come on A
MIL comes on B



A

26.REPLACE COMMON RAIL ASSEMBLY

B

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
26.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/o DPF)>REMOVAL

HINT:

Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

27.BLEED AIR FROM FUEL SYSTEM
27.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
28.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)