Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

Refer to the System Description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High Fuel pressure of common rail is too high:
Fuel pressure exceeds 240000 kPa (2447 kgf/cm2, 34800 psi)
(1 trip detection logic)
·

Fuel supply pump assembly (suction control valve)

·

Open or short in fuel supply pump (suction control valve) circuit

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0088
·

Fuel Press

·

Target Common Rail Pressure

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to the system description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>SYSTEM DESCRIPTION

·

When DTC P0088 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Engine and ECT / Data List / Fuel Press.


Reference
Engine Speed Fuel Press
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa

·

Check "Fuel Press", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0088 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM stores this DTC if the fuel pressure inside the common rail assembly is higher than 240000 kPa (2447 kgf/cm2, 34800 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


WIRING DIAGRAM

A165726E05
6.083,1.813 6.385,1.969 0.302,0.156 10 false C39 6.083,1.969 6.479,2.156 0.396,0.188 10 false ECM 0.625,1.823 0.927,1.979 0.302,0.156 10 false r2 0.625,1.979 2.25,2.344 1.625,0.365 10 false Fuel Temperature Sensor, Suction Control Valve 1.802,0.542 2.01,0.708 0.208,0.167 10 false +B 2.073,0.542 2.229,0.708 0.156,0.167 10 false 1 1.677,1.208 2,1.375 0.323,0.167 10 false PCV 5.354,0.531 5.604,0.698 0.25,0.167 10 false 106 5.354,1.208 5.635,1.375 0.281,0.167 10 false 105 5.698,1.292 6.083,1.458 0.385,0.167 10 false PCV- 5.698,0.625 6.125,0.781 0.427,0.156 10 false PCV+ 2.073,1.208 2.229,1.375 0.156,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
P0088 is output A
P0088 and "P0190, P0192 or P0193" are output B



HINT:

When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.



A

2.CHECK FREEZE FRAME DATA (FUEL PRESS)

B

2.CHECK FREEZE FRAME DATA (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Record the stored DTCs and freeze frame data.


Result:
Result Proceed to
Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data A
Except above B



B

3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

A

9.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/o DPF)>REMOVAL

HINT:

Before replacing the fuel supply pump assembly, check that the wire harness between the suction control valve and ECM is not shorted to ground.

When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1002 to 1202 mA when the engine is running at 2500 rpm without load. If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.

When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the fuel supply pump assembly.



Result:
Proceed to
NEXT



NEXT

4.BLEED AIR FROM FUEL SYSTEM
4.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

5.PERFORM SUPPLY PUMP INITIALIZATION
5.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

6.CHECK IF DTC OUTPUT RECURS (DTC P0088)
6.CHECK IF DTC OUTPUT RECURS (DTC P0088)
a.

Connect the GTS to the DLC3.


b.

Clear DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check the DTC judgment result.



Result:
GTS Display Result Proceed to
Pending DTC P0088 is output A
All Readiness NORMAL B
ABNORMAL A


HINT:

If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.



A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

9.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.


A391015C01
1.813,1.094 2.26,0.594 2.26,0.594 2.344,0.594 true 2.604,2.323 2.531,2.323 2.531,2.323 1.729,1.5 true 0.969,0.458 1.281,0.615 0.313,0.156 10 false *1 2.635,2.24 2.948,2.396 0.313,0.156 10 false *2 2.385,0.51 2.698,0.667 0.313,0.156 10 false *3 3.74,1.406 4.052,1.563 0.313,0.156 10 false *4 5.802,1.167 6.115,1.323 0.313,0.156 10 false *5 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly RH
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


Result:
Result Proceed to
MIL does not come on A
MIL comes on B



A

3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
11.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.


A391015C01
1.813,1.094 2.26,0.594 2.26,0.594 2.344,0.594 true 2.604,2.323 2.531,2.323 2.531,2.323 1.729,1.5 true 0.969,0.458 1.281,0.615 0.313,0.156 10 false *1 2.635,2.24 2.948,2.396 0.313,0.156 10 false *2 2.385,0.51 2.698,0.667 0.313,0.156 10 false *3 3.74,1.406 4.052,1.563 0.313,0.156 10 false *4 5.802,1.167 6.115,1.323 0.313,0.156 10 false *5 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a
*1 Engine *2 Engine Wire
*3 Common Rail Assembly RH
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -


a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.


Result:
Result Proceed to
MIL does not come on A
MIL comes on B



A

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

12.REPLACE COMMON RAIL ASSEMBLY RH (FUEL PRESSURE SENSOR)
12.REPLACE COMMON RAIL ASSEMBLY RH (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly RH.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED