For more information on the injector and the common rail system.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>SYSTEM DESCRIPTION
If DTC P1238 is present, refer to the Diagnostic Trouble Code (DTC) Table for Common Rail System.
The ECM detects combustion deterioration for a specific cylinder.
| *1 | Solenoid Valve | *2 | Piston |
| *3 | Nozzle Needle | - | - |
| *a | Injector Cross Section Diagram | - | - |
The cylinder, which has the compensation value for Injection Feedback Val #1, #2, #3, #4, #5, #6, #7 and #8 that varies from other cylinders, may be malfunctioning.
If DTC P0093 (fuel leaks from high-pressure area) is set simultaneously, a leakage malfunction of the cylinder has probably occurred.
If DTC P062D (open or short in the No. 1 injector driver (EDU) or injector circuit) is set simultaneously, there is probably a faulty circuit located between the ECM and the injector including the No. 1 EDU.
If DTC P062E (open or short in the No. 2 injector driver (EDU) or injector circuit) is set simultaneously, there is probably a faulty circuit located between the ECM and the injector including the No. 2 EDU.
If only DTC P1238 (injector malfunction) is present, an injector mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, EDU or injector circuit is unlikely.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1238 | Injector Malfunction | Engine speed fluctuation is large when idling (2 trip detection logic) |
Main Trouble Area
·
Fuel Injector
·
Injector driver (EDU) (P062D and/or P062E set simultaneously)
·
Open or short in engine wire harness (P062D and/or P062E set simultaneously)
·
Connector connection (P062D and/or P062E set simultaneously)
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | DTC stored |
After confirming DTC P1238, check the internal fuel pressure on the GTS by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
| Engine Speed | Fuel Pressure |
|---|---|
| Idling | Approximately 27000 to 37000 kPa |
| 2500 rpm (No engine load) | Approximately 50000 to 70000kPa |
This DTC will be set if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM sets this DTC.
Refer to DTC P062D.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>P062D
After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION).
If DTCs other than P1238 are present simultaneously, first troubleshoot those DTCs.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P1238 is output | A |
| P1238 and other DTCs are output | B |
If any DTCs other than P1238 are output, troubleshoot those DTCs first.
If DTCs other than P1238 are not output, check the fuel condition before proceeding to next step.
A
B
Check the wire harness and connector connections.
The wire harness and connectors have been connected securely and there are good connections.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.
| Tester Display |
|---|
| Injection Feedback Val #1 |
| Injection Feedback Val #2 |
| Injection Feedback Val #3 |
| Injection Feedback Val #4 |
| Injection Feedback Val #5 |
| Injection Feedback Val #6 |
| Injection Feedback Val #7 |
| Injection Feedback Val #8 |
Read the value.
The compensatory injection volume is between -3.0 mm3/st and 3.0 mm3/st.
If the injector is malfunctioning, the compensatory injection volume remains at -5.0 mm3/st or 5.0 mm3/st.
The compensatory injection volume is usually between -3.0 mm3/st and 3.0 mm3/st.
Any cylinders that have a higher compensatory injection volume than shown above are considered to be faulty. Use the following steps to inspect and repair the cylinders.
| Result | Proceed to |
|---|---|
| Faulty cylinder is not identified | A |
| Faulty cylinder is identified | B |
B
A
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
Check the 8 cylinders in sequence to identify a faulty cylinder by performing the power-balance inspection.
If the engine idle speed does not change when an injector is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.
Clear DTCs.
Before clearing DTCs, save the data stored in the ECM memory if necessary.
Switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>CHECK MODE PROCEDURE
Start the engine and warm it up.
Allow the engine to idle for 60 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P1238 is output | A |
| No DTC is output | B |
A
B
Replace fuel injector.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs.
Switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>CHECK MODE PROCEDURE
Start the engine and warm it up.
Let the engine idle for 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P1238 is output | A |
| No DTC is output | B |
A
B