1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
3.REMOVE EXHAUST PIPE ASSEMBLY
for 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (for 5 Door)>REMOVAL
except 5 Door:
Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST PIPE (except 5 Door)>REMOVAL
51442 4.REMOVE NO. 2 ENGINE UNDER COVER
5.DRAIN ENGINE COOLANT
16571C 6.REMOVE NO. 1 RADIATOR HOSE
17881 7.REMOVE NO. 1 AIR CLEANER HOSE
17705 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
17805 10.REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY
17875 11.REMOVE INTAKE AIR CONNECTOR PIPE
16470 12.REMOVE RADIATOR RESERVOIR ASSEMBLY
16711 13.REMOVE FAN SHROUD
16371 14.REMOVE FAN PULLEY
87240H 15.REMOVE HEATER WATER VALVE ASSEMBLY
Disconnect the cable from the heater water valve assembly.
Slide the 2 clamps and disconnect the 2 hoses from the heater water valve assembly.
Remove the bolt and heater water valve assembly from the vehicle.
67914 16.REMOVE FRONT DOOR SCUFF PLATE LH
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Single Cab)>REMOVAL
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>REMOVAL
67913 17.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62112A 18.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Single Cab)>REMOVAL
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Double Cab)>REMOVAL
62111A 19.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
58191 20.REMOVE FRONT FLOOR FOOTREST (except Pickup)
58811B 21.REMOVE CONSOLE BOX
89179A 22.REMOVE AIRBAG SENSOR COVER
89170 23.REMOVE AIRBAG SENSOR ASSEMBLY WITH AIRBAG SENSOR BRACKET
89441A 24.REMOVE DECELERATION SENSOR
36303 25.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
58286 26.REMOVE NO. 1 SHIFT AND SELECT LEVER BOOT
33530F 27.REMOVE TRANSMISSION SHIFT LEVER ASSEMBLY
| *1 | Shift Lever Cap |
|
Press Down |
|
Counterclockwise |
|
Pull out |
Cover the transmission shift lever cap with a cloth or equivalent.
While pressing down on the transmission shift lever cap, turn it counterclockwise to remove the transmission shift lever.
Pull out the transmission shift lever assembly.
28.REMOVE TRANSFER SHIFT LEVER ASSEMBLY
36308 29.DISCONNECT HIGH AND LOW SHIFT ROD SUB-ASSEMBLY
Remove the nut and washer, and then disconnect the high and low shift rod sub-assembly.
30.DRAIN MANUAL TRANSMISSION OIL
12140 31.REMOVE OIL PAN COVER
Remove the 2 bolts and oil pan cover.
51447C 32.REMOVE TRANSFER CASE PROTECTOR
Remove the 3 bolts and transfer case protector from the No. 2 frame crossmember sub-assembly.
37140 33.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110 34.REMOVE REAR PROPELLER SHAFT ASSEMBLY
31470 35.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY
Remove the 2 bolts and clutch release cylinder assembly.
36.REMOVE FRONT STABILIZER BRACKET LH
Remove the 2 bolts and front stabilizer bracket LH.
37.REMOVE FRONT STABILIZER BRACKET RH
Use the same procedure described for the LH side.
38.SUPPORT MANUAL TRANSMISSION WITH TRANSFER
Support the manual transmission with a transmission jack.
51203 39.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
except Single Cab:
Remove the 8 bolts.
Remove the 2 nuts and No. 2 frame crossmember sub-assembly.
for Single Cab:
Remove the 4 bolts, 6 nuts and No. 2 frame crossmember sub-assembly.
12371 40.REMOVE REAR ENGINE MOUNTING INSULATOR
Remove the 4 bolts and rear engine mounting insulator from the manual transmission with transfer.
41.DISCONNECT GROUND CABLE
Remove the bolt and disconnect the ground cable.
42.DISCONNECT WIRE HARNESS
Remove the 16 wire harness clamps and disconnect the 3 wire harness connectors from the manual transmission with transfer.
Tilt the manual transmission a small amount and release the wire harness connector and wire harness clamp from the manual transmission.
Do not damage the wire harness.
Tilt down the manual transmission with transfer.
Do not damage the wire harness.
Support the engine assembly with the jack and engine lifter so that it is stable as shown in the illustration.
43.REMOVE MANUAL TRANSMISSION WITH TRANSFER
Remove the 10 bolts.
Separate and remove the manual transmission with transfer.
Do not use excess force to pry off the transmission assembly.
44.REMOVE DIFFERENTIAL PRESSURE SENSOR
45.REMOVE TRANSFER ASSEMBLY
46.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 4 bolts and 4 wire harness clamp brackets.
47.REMOVE EXHAUST PIPE SUPPORT
Remove the 2 bolts and exhaust pipe support.
31204 48.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY
31237 49.REMOVE CLUTCH RELEASE FORK SUPPORT BOOT
31236B 50.REMOVE RELEASE FORK SUPPORT