Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P272C00  Park Pawl Motor Driving Time Too Long  


DESCRIPTION

The shift control ECU receives shift lever position signals from the shift lever position sensor (shift lock control unit assembly) and P position switch signal from the P position switch (parking switch) to operate the shift control actuator assembly and detect the time for switching the shift state between park (P) (parking lock engaged) and other than park (P) (parking lock released). When the shift control ECU detects a malfunction at this time, the DTC is stored in the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P272C00 Park Pawl Motor Driving Time Too Long When the ignition switch is ON, a shift control actuator assembly (parking lock motor) internal malfunction (parking lock motor spins freely) is detected for 2 seconds or more
(1 trip detection logic)
·

Shift control actuator assembly

·

FCV transaxle with motor assembly

·

Shift control ECU

·

Auxiliary battery

·

P CON MTR relay


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON.

2.

Depress the brake pedal and move the shift lever to select neutral (N).

3.

Push the P position switch (parking switch) to select park (P).


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

Pre-procedure1

a.

None


Procedure1

a.

Check if the DTCs related to yaw rate sensor malfunction, acceleration sensor malfunction, or CAN bus malfunction are output from the electronically controlled brake system.

Chassis > Brake/EPB > Trouble Codes
50001 435

b.

Check if DTCs are output.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (BATT VOLTAGE FOR GEAR SHIFT CONTROL MODULE)

B

2.CHECK FREEZE FRAME DATA (BATT VOLTAGE FOR GEAR SHIFT CONTROL MODULE)

Pre-procedure1

a.

Turn the ignition switch to ON.

HINT:

It may not be possible to turn the ignition switch to ON (READY).



Procedure1

a.

Read the freeze frame data of DTC P272C00.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV > DTC(P272C00) > Freeze Frame Data
Tester Display
BATT Voltage for Gear Shift Control Module
50040 397 567 P272C00

Result:
Result Proceed to
The value of BATT Voltage for Gear Shift Control Module is 9 V or more A
The value of BATT Voltage for Gear Shift Control Module is less than 9 V B


Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

B

5.CHARGE AUXILIARY BATTERY
3.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

Pre-procedure1

a.

Check that the parking brake is applied.


b.

Pull the shift control actuator assembly from the FCV with motor transaxle assembly.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT CONTROL ACTUATOR>REMOVAL



c.

Reconnect the G153 shift control actuator assembly connector.


d.

Release the brake pedal and turn the ignition switch to ACC.

NOTICE:

The shift control actuator assembly may operate if the ignition switch is turned to ON or ON (READY). Do not turn the ignition switch to ON or ON (READY) during this inspection to prevent the shift control actuator assembly from operating while in contact with the splines.



Procedure1

a.
C450304

Using a screwdriver with its tip wrapped with protective tape or a piece of cloth, rotate the shaft.

NOTICE:
·

During this inspection, make sure to use a screwdriver with its tip wrapped with protective tape or a piece of cloth to prevent the splines of the actuator from being damaged.

·

Rotate the shaft with torque of 2 N*m (20.3 kgf*cm, 17.7 in.*lbf) or less. Do not apply load while the contacting the stopper inside the actuator.

·

The shift control actuator assembly cannot be disassembled.



i.

Confirm that the shaft of the shift control actuator assembly rotates smoothly.

OK:

The shaft of the shift control actuator assembly rotates smoothly.



ii.
C375413C26
1.583,0.354 1.906,0.573 0.323,0.219 1.073,1.979 1.469,1.323 true 2.135,1.958 1.542,1.323 true 2.885,1.948 1.667,1.323 true 1.625,0.396 2.083,0.594 0.458,0.198 10 false A44 2.75,2.01 3.281,2.188 0.531,0.177 10 false 21 (RB) 1.948,2.031 2.479,2.208 0.531,0.177 10 false 23 (RA) 0.875,2.031 1.406,2.208 0.531,0.177 10 false 24 (E2) 0.51,3.031 0.823,3.229 0.313,0.198 10 false RA 0.521,3.563 0.833,3.76 0.313,0.198 10 false RB 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.156,2.49 0.469,2.688 0.313,0.198 10 false *b
*a Component with harness connected
(Shift Control ECU)
*b Output Waveform while Splines of Shift Control Actuator Assembly being Rotated (Example)


Measure the voltage according to the value(s) in the table below.

NOTICE:

When measuring the voltage, turn the shift control actuator assembly slowly.


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A44)Location & Routing

Click Connector(A44)Instrument Panel>Front Compartment Main Wire>Shift Control ECU

A44-23 (RA) - A44-24 (E2) Ignition switch ACC, shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V
A44-21 (RB) - A44-24 (E2) Ignition switch ACC, shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V




Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

4.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY

NG

4.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY

Pre-procedure1

a.

None


Procedure1

a.
C450303

Wrap the shaft with a piece of cloth and turn it using pliers.

OK:

The shaft rotates smoothly in the lock and unlock directions.


NOTICE:
·

Rotate the shaft using torque between 4.0 and 7.0 N*m (41 and 71 kgf*cm, 36 and 61 in.*lbf).

·

During this inspection, make sure to use a piece of cloth to prevent the shaft splines from being damaged.




Result:
Proceed to
OK
NG


Post-procedure1

a.

Set the shaft in the lock position after the inspection.



OK

NG

5.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Check for DTCs and freeze frame data and then write them down.

Powertrain > EV > Trouble Codes
50001 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.CLEAR DTC
7.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.


b.

Leave the vehicle as is for 60 seconds or more.

NOTICE:
·

Do not connect the GTS.

·

Do not depress the brake pedal.

·

Do not open/close any of the doors.





NEXT

8.CHECK DTC OUTPUT (SIMULATION TEST)
8.CHECK DTC OUTPUT (SIMULATION TEST)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Check that the shift state is neutral (N), and then push the P position switch (parking switch) to select park (P).


d.

Turn the ignition switch to ON (READY).


e.

Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.


f.

Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.


g.

Stop the vehicle and push the P position switch (parking switch) to select park (P).


h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON and wait for 10 seconds or more.

HINT:

It may not be possible to turn the ignition switch to ON (READY).



j.

Depress the brake pedal and move the shift lever to select neutral (N).


k.

Push the P position switch (parking switch) to select park (P).


Procedure1

a.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
Only P272C00 is output B
P272C00 and other DTCs are output C


Post-procedure1

a.

Turn the ignition switch off.



A

END

B

C

GO TO DTC CHART