Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  U010387  Lost Communication with Gear Shift Control Module "A" (Hybrid/EV Battery Local Bus) Missing Message  


DESCRIPTION

The shift control ECU transmits and receives signals via CAN communication to and from the EV control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
U010387 Lost Communication with Gear Shift Control Module "A" (Hybrid/EV Battery Local Bus) Missing Message 3 seconds elapse after turning ignition switch to ON with auxiliary battery voltage 10 V or higher and a CAN communication malfunction (battery local bus) between EV control ECU occurs continuously for 1 second or more.
(1 trip detection logic)
·

EV control ECU

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 2 minutes or more.


WIRING DIAGRAM

C452455E02
0.646,1.594 1.104,1.792 0.458,0.198 10 false D92 0.646,1.854 3.25,2.052 2.604,0.198 10 false Shift Control ECU 5.375,1.844 7.021,2.063 1.646,0.219 10 false Battery ECU Assembly 5.365,1.604 5.979,1.802 0.615,0.198 10 false G156 5.542,0.458 6.156,0.656 0.615,0.198 10 false CA1H 5.24,0.26 5.396,0.458 0.156,0.198 10 false 4 5.542,1.073 6.156,1.271 0.615,0.198 10 false CA1L 5.188,0.885 5.5,1.083 0.313,0.198 10 false 13 1.458,0.458 2.073,0.656 0.615,0.198 10 false CA2H 2.01,0.281 2.167,0.479 0.156,0.198 10 false 6 1.458,1.063 2.073,1.26 0.615,0.198 10 false CA2L 2.01,0.885 2.167,1.083 0.156,0.198 10 false 5 3.802,4.813 4.417,5.01 0.615,0.198 10 false CA4H 4.135,4.542 4.292,4.74 0.156,0.198 10 false 2 3.063,4.823 3.677,5.021 0.615,0.198 10 false CA4L 3.354,4.552 3.51,4.75 0.156,0.198 10 false 3 2.594,5.604 2.979,5.813 0.385,0.208 10 false A8*1 2.604,5.823 4.75,6.021 2.146,0.198 10 false EV Control ECU 0.677,6.323 4.344,6.521 3.667,0.198 10 false : CAN Communication Line 3.031,5.604 3.823,5.802 0.792,0.198 10 false D15*2 5.583,4.313 6.5,4.51 0.917,0.198 10 false *1: for LHD 5.583,4.708 6.5,4.906 0.917,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION



PROCEDURE

1.CHECK DTC OUTPUT (HEALTH CHECK)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Using the GTS, perform a Health Check.

Result:
Result Proceed to
P176D12 is not output A
P176D12 is output. B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)
a.
for LHD:
C452170

for RHD:
C450295

Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN BUS

NG

CONNECT SECURELY

3.CHECK CAN BUS

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) or D92-5 (CA2L) - Body ground Cable from negative (-) auxiliary battery terminal disconnected 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

4.CHECK CAN BUS

NG

9.CHECK FOR SHORT IN CAN BUS (SHIFT CONTROL ECU)
4.CHECK CAN BUS

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) - D92-5 (CA2L) Cable from negative (-) auxiliary battery terminal disconnected 54 to 69 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

5.CHECK VEHICLE TYPE
5.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

6.CHECK FOR OPEN IN CAN BUS (EV CONTROL ECU)

B

8.CHECK FOR OPEN IN CAN BUS (EV CONTROL ECU)
6.CHECK FOR OPEN IN CAN BUS (EV CONTROL ECU)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A8 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) - D92-5 (CA2L) Cable from negative (-) auxiliary battery terminal disconnected 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the A8 EV control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

7.CHECK FOR OPEN IN CAN BUS (BATTERY ECU ASSEMBLY)
7.CHECK FOR OPEN IN CAN BUS (BATTERY ECU ASSEMBLY)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G156 battery ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) - D92-5 (CA2L) Cable from negative (-) auxiliary battery terminal disconnected 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 battery ECU assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FOR OPEN IN CAN BUS (EV CONTROL ECU)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D15 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) - D92-5 (CA2L) Cable from negative (-) auxiliary battery terminal disconnected 108 to 132 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D15 EV control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

7.CHECK FOR OPEN IN CAN BUS (BATTERY ECU ASSEMBLY)
9.CHECK FOR SHORT IN CAN BUS (SHIFT CONTROL ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D92 shift control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) or D92-5 (CA2L) - Body ground Cable from negative (-) auxiliary battery terminal disconnected 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D92 shift control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

10.CHECK VEHICLE TYPE
10.CHECK VEHICLE TYPE
Result:
Result Proceed to
for LHD A
for RHD B



A

11.CHECK FOR SHORT IN CAN BUS (EV CONTROL ECU)

B

13.CHECK FOR SHORT IN CAN BUS (EV CONTROL ECU)
11.CHECK FOR SHORT IN CAN BUS (EV CONTROL ECU)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A8 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) or D92-5 (CA2L) - Body ground Cable from negative (-) auxiliary battery terminal disconnected 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the A8 EV control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

12.CHECK FOR SHORT IN CAN BUS (BATTERY ECU ASSEMBLY)
12.CHECK FOR SHORT IN CAN BUS (BATTERY ECU ASSEMBLY)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the G156 battery ECU assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) or D92-5 (CA2L) - Body ground Cable from negative (-) auxiliary battery terminal disconnected 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the G156 battery ECU assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK FOR SHORT IN CAN BUS (EV CONTROL ECU)

Pre-procedure1

a.
C450252C02
0.792,0.281 1.167,0.552 0.375,0.271 0.969,0.906 0.521,1.75 true 1.031,0.917 1.938,1.75 true 0.865,0.354 1.198,0.521 0.333,0.167 10 false D92 0.25,1.792 0.938,1.969 0.688,0.177 10 false 6 (CH2H) 1.802,1.802 3.031,2 1.229,0.198 10 false 5 (CA2L) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Shift Control ECU)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D15 EV control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D92)Location & Routing

Click Connector(D92)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D92-6 (CA2H) or D92-5 (CA2L) - Body ground Cable from negative (-) auxiliary battery terminal disconnected 200 Ω or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D15 EV control ECU connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



OK

NG

12.CHECK FOR SHORT IN CAN BUS (BATTERY ECU ASSEMBLY)