Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When the M1 or M2 switch of the seat memory switch is pressed, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU assembly LH (for LHD) or RH (for RHD). The position control ECU assembly LH (for LHD) or RH (for RHD) operates each motor to move the seat to the memorized position.

WIRING DIAGRAM

for LHD


E395545E08
0.479,1.229 2.135,1.792 1.656,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 0.667,2.76 2,3.229 1.333,0.469 10 false Position Control ECU Assembly LH 2.594,3.042 4.083,3.542 1.49,0.5 10 false Front Multiplex Network Door ECU LH 5.167,2.958 5.521,3.229 0.354,0.271 10 false E28 2.615,2.875 2.99,3.125 0.375,0.25 10 false E25 5.167,3.146 6.75,3.542 1.583,0.396 10 false Seat Memory Switch LH 0.635,3.427 2.802,3.656 2.167,0.229 10 false : CAN Communication Line 4.021,0.385 4.333,0.583 0.313,0.198 10 false 22 4.031,1.063 4.344,1.26 0.313,0.198 10 false 23 4.031,1.813 4.344,2.01 0.313,0.198 10 false 25 4.031,2.458 4.344,2.656 0.313,0.198 10 false 26 4.865,0.406 5.177,0.604 0.313,0.198 10 false 3 4.865,1.063 5.177,1.26 0.313,0.198 10 false 4 4.885,1.813 5.198,2.01 0.313,0.198 10 false 2 2.875,2.448 3.188,2.646 0.313,0.198 10 false 1 4.896,2.438 5.208,2.635 0.313,0.198 10 false 1 5.052,0.385 5.385,0.635 0.333,0.25 10 false M1 5.052,1.052 5.417,1.302 0.365,0.25 10 false M2 5.052,1.76 5.625,1.99 0.573,0.229 10 false MMRY 5.063,2.438 5.375,2.635 0.313,0.198 10 false E 3.719,0.5 4.052,0.729 0.333,0.229 10 false M1 3.708,1.156 4.083,1.406 0.375,0.25 10 false M2 3.667,1.906 3.99,2.104 0.323,0.198 10 false MM 3.49,2.552 4.094,2.865 0.604,0.313 10 false MSWE 3.073,2.563 3.563,2.76 0.49,0.198 10 false GND 5.271,0.625 6.01,0.792 0.74,0.167 10 false M1 Switch 5.323,1.323 6.177,1.656 0.854,0.333 10 false M2 Switch 5.219,2.083 5.958,2.25 0.74,0.167 10 false SET Switch


for RHD


E395545E06
0.479,1.229 2.135,1.792 1.656,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 0.667,2.76 2,3.229 1.333,0.469 10 false Position Control ECU Assembly RH 2.594,3.042 4.083,3.542 1.49,0.5 10 false Front Multiplex Network Door ECU RH 5.167,2.958 5.521,3.229 0.354,0.271 10 false E10 2.615,2.875 2.927,3.073 0.313,0.198 10 false E7 5.167,3.146 6.75,3.542 1.583,0.396 10 false Seat Memory Switch RH 0.635,3.427 2.802,3.656 2.167,0.229 10 false : CAN Communication Line 4.031,0.406 4.344,0.604 0.313,0.198 10 false 22 4.031,1.073 4.344,1.271 0.313,0.198 10 false 23 4.031,1.813 4.344,2.01 0.313,0.198 10 false 25 4.031,2.458 4.344,2.656 0.313,0.198 10 false 26 4.865,0.406 5.177,0.604 0.313,0.198 10 false 3 4.875,1.083 5.188,1.281 0.313,0.198 10 false 4 4.885,1.813 5.198,2.01 0.313,0.198 10 false 2 2.875,2.448 3.188,2.646 0.313,0.198 10 false 1 4.896,2.438 5.208,2.635 0.313,0.198 10 false 1 5.052,0.385 5.385,0.635 0.333,0.25 10 false M1 5.073,1.083 5.438,1.333 0.365,0.25 10 false M2 5.063,1.76 5.573,1.948 0.51,0.188 10 false MRY 5.063,2.438 5.375,2.635 0.313,0.198 10 false E 3.74,0.5 4.052,0.698 0.313,0.198 10 false M1 3.729,1.156 4.042,1.354 0.313,0.198 10 false M2 3.667,1.906 3.99,2.104 0.323,0.198 10 false MM 3.49,2.552 4.094,2.865 0.604,0.313 10 false MSWE 3.073,2.563 3.563,2.76 0.49,0.198 10 false GND 5.271,0.625 6.01,0.792 0.74,0.167 10 false M1 Switch 5.323,1.323 6.177,1.656 0.854,0.333 10 false M2 Switch 5.219,2.083 5.958,2.25 0.74,0.167 10 false SET Switch


CAUTION / NOTICE / HINT

*1: for LHD

*2: for RHD


NOTICE:
·

In cases where the headrest may interfere with the roof headlining during a memory call operation, the avoids interference function prohibits recall operations.

·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Initializing the position control ECU assembly LH*1 or RH*2 will clear the seat position memory.



HINT:

Make sure to initialize the position control ECU assembly LH*1 or RH*2 after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>REGISTRATION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FRONT POWER SEAT CONTROL OPERATION

B

12.CHECK FRONT POWER SEAT CONTROL OPERATION
2.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch LH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY FUNCTION

NG

3.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

4.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

·

The ignition switch is ON, and the shift lever is in P.*1

·

Within 180 seconds after the driver door is opened with the ignition switch off.*2

·

Within 60 seconds after the driver door is opened and then closed with the ignition switch off.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

5.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

8.READ VALUE USING GTS (SHIFT P POSITION STATE)

C

11.READ VALUE USING GTS (FL DOOR COURTESY SW)
5.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


b.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

6.REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

6.REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH
a.

Replace the front multiplex network door ECU LH with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (FRONT MULTIPLEX NETWORK DOOR ECU LH WAS DEFECTIVE)

NG

9.REPLACE POSITION CONTROL ECU ASSEMBLY LH
8.READ VALUE USING GTS (SHIFT P POSITION STATE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Position Current shift state Shift other / Sift P Shift other: Shift lever is not P
Shift P: Shift lever is P
-
Body Electrical > Driver Seat > Data List
Tester Display
Shift SW Position
50003 162 229
OK:

On the GTS screen, the current shift state is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

9.REPLACE POSITION CONTROL ECU ASSEMBLY LH
a.

Replace the position control ECU assembly LH with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
10.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

11.READ VALUE USING GTS (FL DOOR COURTESY SW)
a.

Read the Data List according to the display on the GTS.

OK:

On the GTS screen, ON or OFF is displayed accordingly.


Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199

Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

12.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch RH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally.



Result:
Proceed to
OK
NG



OK

13.CHECK SEAT POSITION MEMORY FUNCTION

NG

13.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

14.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

14.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

·

The ignition switch is ON, and the shift lever is in P.*1

·

Within 180 seconds after the driver door is opened with the ignition switch off.*2

·

Within 60 seconds after the driver door is opened and then closed with the ignition switch off.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

15.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

18.READ VALUE USING GTS (SHIFT P POSITION STATE)

C

21.READ VALUE USING GTS (FR DOOR COURTESY SW)
15.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


b.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

16.REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

16.REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH
a.

Replace the front multiplex network door ECU RH with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

17.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
17.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (FRONT MULTIPLEX NETWORK DOOR ECU RH WAS DEFECTIVE)

NG

19.REPLACE POSITION CONTROL ECU ASSEMBLY RH
18.READ VALUE USING GTS (SHIFT P POSITION STATE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Position Current shift state Shift other / Sift P Shift other: Shift lever is not P
Shift P: Shift lever is P
-
Body Electrical > Driver Seat > Data List
Tester Display
Shift SW Position
50003 162 229
OK:

On the GTS screen, the current shift state is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

19.REPLACE POSITION CONTROL ECU ASSEMBLY RH
a.

Replace the position control ECU assembly RH with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
20.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.READ VALUE USING GTS (FR DOOR COURTESY SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF ON: Front door RH open
CFF: Front door RH closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)