Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM37H0E _58 Vehicle Interior _095292 SEAT _0457023 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Power Easy Access System Function does not Operate  


DESCRIPTION

·

Perform either of the following and check that the driver seat moves rearward:

-

With the ignition switch off and the shift lever in P, unfasten the driver seat seat belt.

-

With the shift lever in P and the driver seat seat belt unfastened, turn the ignition switch off.


·

Perform either of the following and check that the driver seat moves forward:

-

With the shift lever in P, fasten the driver seat seat belt.

-

With the shift lever in P, turn the ignition switch from off to ON.



WIRING DIAGRAM

for LHD


B584175E09
0.25,2.667 1.948,3.063 1.698,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 2.906,2.854 4.25,3.448 1.344,0.594 10 false Position Control ECU Assembly LH 2.906,2.667 3.729,2.885 0.823,0.219 10 false L43 0.563,3.448 4.229,3.646 3.667,0.198 10 false : CAN Communication Line 3.854,1.427 4.167,1.625 0.313,0.198 10 false 27 4.688,1.333 4.844,1.531 0.156,0.198 10 false 1 6,1.344 6.156,1.542 0.156,0.198 10 false 2 4.375,1.927 6.615,2.344 2.24,0.417 10 false Front Seat Inner Belt Assembly LH 4.635,1.552 5.094,1.75 0.458,0.198 10 false L38 5.927,1.542 6.385,1.74 0.458,0.198 10 false L38


for RHD


B584175E10
0.25,2.667 1.948,3.063 1.698,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 2.906,2.854 4.25,3.448 1.344,0.594 10 false Position Control ECU Assembly RH 2.906,2.667 3.729,2.885 0.823,0.219 10 false L17 0.563,3.448 4.229,3.646 3.667,0.198 10 false : CAN Communication Line 3.854,1.427 4.167,1.625 0.313,0.198 10 false 27 4.688,1.333 4.844,1.531 0.156,0.198 10 false 1 6,1.344 6.156,1.542 0.156,0.198 10 false 2 4.375,1.948 6.615,2.365 2.24,0.417 10 false Front Seat Inner Belt Assembly RH 4.635,1.552 5.094,1.75 0.458,0.198 10 false L13 5.927,1.542 6.385,1.74 0.458,0.198 10 false L13


CAUTION / NOTICE / HINT

NOTICE:
·

The front power seat control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.



HINT:

When troubleshooting a function, first make sure that the function is set to the default setting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>CUSTOMIZE PARAMETERS


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FRONT POWER SEAT OPERATION

B

5.CHECK FRONT POWER SEAT OPERATION
2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch LH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Power seat functions operate normally A
All power seat functions do not operate B
One or more power seat motors do not operate C




A

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

B

GO TO OTHER FLOW CHART (Front Power Seat does not Operate with Front Power Seat Switch)

C

GO TO OTHER FLOW CHART (One or more Power Seat Motors do not Operate)

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - FRONT SEAT INNER BELT ASSEMBLY LH - BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY LH - FRONT SEAT INNER BELT ASSEMBLY LH - BODY GROUND)
a.

Disconnect the L43 position control ECU assembly LH connector.


b.

Disconnect the L38 front seat inner belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L43,L38)Location & Routing

Click Connector(L43)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly LH

Click Connector(L38)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Inner Belt Assembly LH

L43-27 - L38-1 Always Below 1 Ω
L43-27 or L38-1 - Body ground Always 10 kΩ or higher
L38-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch RH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
Power seat functions operate normally A
All power seat functions do not operate B
One or more power seat motors do not operate C




A

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

B

GO TO OTHER FLOW CHART (Front Power Seat does not Operate with Front Power Seat Switch)

C

GO TO OTHER FLOW CHART (One or more Power Seat Motors do not Operate)

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY RH - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the L17 position control ECU assembly RH connector.


b.

Disconnect the L13 front seat inner belt assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L17,L13)Location & Routing

Click Connector(L17)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Position Control ECU Assembly RH

Click Connector(L13)Seat>Front Seat Wire RH / No. 2 Front Seat Wire LH / No. 2 Front Seat Wire RH>Front Seat Inner Belt Assembly RH

L17-27 - L13-1 Always Below 1 Ω
L17-27 or L13-1 - Body ground Always 10 kΩ or higher
L13-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR