Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P1A6116  Hybrid/EV Battery Stack 2 Cell Circuit Voltage Below Threshold  P31AB16  Hybrid/EV Battery Stack 1 Cell Circuit Voltage Below Threshold  


DESCRIPTION

When a certain amount of time passes during which the EV battery cell voltage is below the specified value, the battery voltage sensor informs the battery ECU assembly of any malfunctions. The battery ECU assembly stores these DTCs.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1A6116 Hybrid/EV Battery Stack 2 Cell Circuit Voltage Below Threshold The voltage of any cell of the No. 2 EV supply stack sub-assembly has decreased excessively.
(1 trip detection logic)
·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

Battery voltage sensor (for lower side)


Master Warning:
Comes on
EV Battery A
P31AB16 Hybrid/EV Battery Stack 1 Cell Circuit Voltage Below Threshold The voltage of any cell of the No. 1 EV supply stack sub-assembly has decreased excessively.
(1 trip detection logic)
·

No. 1 EV supply stack sub-assembly

·

EV battery terminal block

·

Battery voltage sensor (for upper side)


Master Warning:
Comes on
EV Battery A

CAUTION:

Do not charge the EV supply battery assembly using the THS charger if DTC P1A6116 or P31AB16 is output.


Related Data List
DTC No. Data List
P1A6116 Hybrid/EV Battery Cell 1 to 84 Voltage
P31AB16

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Drive the vehicle on urban roads for approximately 10 minutes.

4.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly is disposed of improperly or abandoned. Therefore, make sure to return all EV supply battery assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly to produce heat, resulting in a fire.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P1A6116 or P31AB16 for Hybrid battery system is output A
P1A6116 or P31AB16 is output and DTCs other than the DTCs in the table below are output B
P1A6116 or P31AB16 is output and Hybrid battery system DTCs in the table below are output C
P1A6116 or P31AB16 is output and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK ODOMETER

B

2.CHECK ODOMETER

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1A6116" is also output. A
"P31AB16" is also output. B



A

4.CHECK FREEZE FRAME DATA

B

12.CHECK FREEZE FRAME DATA
4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 43 Voltage" through "Hybrid/EV Battery Cell 84 Voltage" for DTC P1A6116 and make a note if the value of any is 1.6 V or less.

HINT:

Use this for reference when measuring the EV battery cell voltage.


Powertrain > EV Battery > DTC(P1A6116) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
Hybrid/EV Battery Cell 49 Voltage
Hybrid/EV Battery Cell 50 Voltage
Hybrid/EV Battery Cell 51 Voltage
Hybrid/EV Battery Cell 52 Voltage
Hybrid/EV Battery Cell 53 Voltage
Hybrid/EV Battery Cell 54 Voltage
Hybrid/EV Battery Cell 55 Voltage
Hybrid/EV Battery Cell 56 Voltage
Hybrid/EV Battery Cell 57 Voltage
Hybrid/EV Battery Cell 58 Voltage
Hybrid/EV Battery Cell 59 Voltage
Hybrid/EV Battery Cell 60 Voltage
Hybrid/EV Battery Cell 61 Voltage
Hybrid/EV Battery Cell 62 Voltage
Hybrid/EV Battery Cell 63 Voltage
Hybrid/EV Battery Cell 64 Voltage
Hybrid/EV Battery Cell 65 Voltage
Hybrid/EV Battery Cell 66 Voltage
Hybrid/EV Battery Cell 67 Voltage
Hybrid/EV Battery Cell 68 Voltage
Hybrid/EV Battery Cell 69 Voltage
Hybrid/EV Battery Cell 70 Voltage
Hybrid/EV Battery Cell 71 Voltage
Hybrid/EV Battery Cell 72 Voltage
Hybrid/EV Battery Cell 73 Voltage
Hybrid/EV Battery Cell 74 Voltage
Hybrid/EV Battery Cell 75 Voltage
Hybrid/EV Battery Cell 76 Voltage
Hybrid/EV Battery Cell 77 Voltage
Hybrid/EV Battery Cell 78 Voltage
Hybrid/EV Battery Cell 79 Voltage
Hybrid/EV Battery Cell 80 Voltage
Hybrid/EV Battery Cell 81 Voltage
Hybrid/EV Battery Cell 82 Voltage
Hybrid/EV Battery Cell 83 Voltage
Hybrid/EV Battery Cell 84 Voltage
50040 398 376,377,378,379,380,381,382,383,384,385,386,387,388,389,390,391,392,393,394,395,396,397,398,399,400,401,402,403,404,405,406,407,408,409,410,411,412,413,414,415,416,417 P1A6116

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)
5.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z16 or z17 was not connected securely The terminals are damaged or corroded C



A

6.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

10.CHECK TOTAL DISTANCE DRIVEN
6.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



A

7.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)

B

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

7.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B



A

8.CHECK TOTAL DISTANCE DRIVEN

B

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

8.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

9.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
9.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

10.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

11.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
11.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

12.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 42 Voltage" for DTC P31AB16 and make a note if the value of any is 1.6 V or less.

HINT:

Use this for reference when measuring the EV battery cell voltage.


Powertrain > EV Battery > DTC(P31AB16) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
50040 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375 P31AB16

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

13.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)
13.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z14 or z15 was not connected securely The terminals are damaged or corroded C



A

14.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

18.CHECK TOTAL DISTANCE DRIVEN
14.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



A

15.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)

B

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

15.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B



A

16.CHECK TOTAL DISTANCE DRIVEN

B

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

16.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

17.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
17.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

18.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

19.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
19.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK