Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0453477 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0E2D00  Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance  


DESCRIPTION

The battery voltage sensor detects the cell voltage of the EV supply battery assembly. The battery voltage sensor performs self diagnosis of the internal cell voltage detection circuit, and informs the battery ECU assembly of the result. The battery ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance The battery voltage sensor detects a malfunction of its internal EV battery cell voltage detection circuits.
(1 trip detection logic)
·

Battery ECU assembly

·

Battery voltage sensor (for upper side)

·

Battery voltage sensor (for lower side)

·

No. 1 EV supply stack sub-assembly

·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

Wire harness or connector

·

FCV with motor transaxle assembly

·

FC air compressor with motor assembly

·

Inverter with converter assembly

·

No. 2 battery pack wire

·

Motor cable

·

FC air compressor motor cable assembly


Master Warning:
Comes on
EV Battery A

Related Data List
DTC No. Data List
P0E2D00
·

Hybrid/EV Battery Cell 1 to 84 Voltage

·

Lost Communication with Hybrid/EV Battery Monitoring IC

·

Hybrid/EV Battery Monitoring IC 1 Internal Malfunction (Determinable)

·

Hybrid/EV Battery Monitoring IC 2 Internal Malfunction (Determinable)

·

Hybrid/EV Battery Monitoring IC 3 Internal Malfunction (Determinable)

·

Hybrid/EV Battery Monitoring IC 4 Internal Malfunction (Determinable)

·

Hybrid/EV Battery Monitoring IC Internal Malfunction (Unidentifiable)

·

Hybrid/EV Battery Monitoring IC 1 Power Supply Malfunction

·

Hybrid/EV Battery Monitoring IC 2 Power Supply Malfunction

·

Hybrid/EV Battery Monitoring IC 3 Power Supply Malfunction

·

Hybrid/EV Battery Monitoring IC 4 Power Supply Malfunction

·

Hybrid/EV Battery Monitoring IC 1 Cell Voltage Detection Malfunction

·

Hybrid/EV Battery Monitoring IC 2 Cell Voltage Detection Malfunction

·

Hybrid/EV Battery Monitoring IC 3 Cell Voltage Detection Malfunction

·

Hybrid/EV Battery Monitoring IC 4 Cell Voltage Detection Malfunction

·

Short Wave Highest Value



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

With the vehicle stopped and the shift position in P, turn the ignition switch to ON and wait for at least 70 seconds.

4.

Turn the ignition switch to ON (READY) and without depressing the accelerator pedal, and while depressing the brake pedal, change the shift position to D and wait for 1 minute. (Step A)

5.

Drive the vehicle 0.5 m (1.6 ft.) forward and perform step A.

6.

Drive the vehicle another 0.5 m (1.6 ft.) forward and perform step A. Repeat this procedure 5 times (minimum total driving distance: 2 m (6.6 ft.)).

7.

Enter the following menus: Powertrain / EV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

C375132E06
5.271,0.823 5.885,1.021 0.615,0.198 10 false VA42 5.271,1.042 5.885,1.24 0.615,0.198 10 false VA41 5.26,1.281 5.875,1.479 0.615,0.198 10 false VA40 5.26,1.51 5.875,1.708 0.615,0.198 10 false VA39 5.271,1.75 5.885,1.948 0.615,0.198 10 false VA38 5.26,1.979 5.875,2.177 0.615,0.198 10 false VA37 5.271,2.208 5.885,2.406 0.615,0.198 10 false VA36 5.271,2.448 5.885,2.646 0.615,0.198 10 false VA35 5.271,2.688 5.885,2.885 0.615,0.198 10 false VA34 5.281,2.917 5.896,3.115 0.615,0.198 10 false VA33 5.271,3.146 5.885,3.344 0.615,0.198 10 false VA32 5.271,3.375 5.885,3.573 0.615,0.198 10 false VA31 5.271,3.625 5.885,3.823 0.615,0.198 10 false VA30 5.271,3.865 5.885,4.063 0.615,0.198 10 false VA29 5.271,4.094 5.885,4.292 0.615,0.198 10 false VA28 5.271,4.323 5.885,4.521 0.615,0.198 10 false VA27 5.271,4.573 5.885,4.771 0.615,0.198 10 false VA26 5.271,4.802 5.885,5 0.615,0.198 10 false VA25 5.271,5.063 5.885,5.26 0.615,0.198 10 false VA24 5.271,5.323 5.885,5.521 0.615,0.198 10 false VA23 5.271,5.563 5.729,5.76 0.458,0.198 10 false GA1 3.521,0.719 4.135,0.917 0.615,0.198 10 false VA42 3.521,0.958 4.135,1.156 0.615,0.198 10 false VA41 3.521,1.188 4.135,1.385 0.615,0.198 10 false VA40 3.531,1.417 4.146,1.615 0.615,0.198 10 false VA39 3.521,1.667 4.135,1.865 0.615,0.198 10 false VA38 3.521,1.896 4.135,2.094 0.615,0.198 10 false VA37 3.521,2.125 4.135,2.323 0.615,0.198 10 false VA36 3.521,2.354 4.135,2.552 0.615,0.198 10 false VA35 3.521,2.604 4.135,2.802 0.615,0.198 10 false VA34 3.521,2.854 4.135,3.052 0.615,0.198 10 false VA33 3.521,3.073 4.135,3.271 0.615,0.198 10 false VA32 3.521,3.302 4.135,3.5 0.615,0.198 10 false VA31 3.521,3.542 4.135,3.74 0.615,0.198 10 false VA30 3.521,3.781 4.135,3.979 0.615,0.198 10 false VA29 3.521,4.021 4.135,4.219 0.615,0.198 10 false VA28 3.521,4.25 4.135,4.448 0.615,0.198 10 false VA27 3.521,4.49 4.135,4.688 0.615,0.198 10 false VA26 3.521,4.729 4.135,4.927 0.615,0.198 10 false VA25 3.521,4.99 4.135,5.188 0.615,0.198 10 false VA24 3.521,5.229 4.135,5.427 0.615,0.198 10 false VA23 3.583,5.479 4.042,5.677 0.458,0.198 10 false GA1 5.021,0.719 5.177,0.917 0.156,0.198 10 false 1 4.948,0.969 5.26,1.167 0.313,0.198 10 false 11 5.01,1.198 5.167,1.396 0.156,0.198 10 false 2 4.948,1.417 5.26,1.615 0.313,0.198 10 false 12 5.01,1.667 5.167,1.865 0.156,0.198 10 false 3 5,1.906 5.156,2.104 0.156,0.198 10 false 4 4.948,2.135 5.26,2.333 0.313,0.198 10 false 13 5.01,2.365 5.167,2.563 0.156,0.198 10 false 5 4.948,2.604 5.26,2.802 0.313,0.198 10 false 14 4.948,2.844 5.26,3.042 0.313,0.198 10 false 15 4.938,3.073 5.25,3.271 0.313,0.198 10 false 16 4.938,3.302 5.25,3.5 0.313,0.198 10 false 17 4.927,3.542 5.24,3.74 0.313,0.198 10 false 18 4.938,3.792 5.25,3.99 0.313,0.198 10 false 19 4.948,4.021 5.26,4.219 0.313,0.198 10 false 20 4.948,4.271 5.26,4.469 0.313,0.198 10 false 21 5,4.5 5.156,4.698 0.156,0.198 10 false 6 4.927,4.719 5.24,4.917 0.313,0.198 10 false 22 5,4.99 5.156,5.188 0.156,0.198 10 false 7 5,5.229 5.156,5.427 0.156,0.198 10 false 8 4.927,5.479 5.24,5.677 0.313,0.198 10 false 23 1.51,6.385 5.177,6.583 3.667,0.198 10 false No. 1 EV Supply Stack Sub-assembly 4.667,6.083 7.094,6.292 2.427,0.208 10 false Battery Voltage Sensor (for Upper Side) 4.677,5.885 5.135,6.083 0.458,0.198 10 false z15

C375133E06
5.281,6.021 5.74,6.219 0.458,0.198 10 false GA0 5.271,5.771 5.729,5.969 0.458,0.198 10 false VA1 5.271,5.552 5.729,5.75 0.458,0.198 10 false VA2 5.271,5.313 5.729,5.51 0.458,0.198 10 false VA3 5.271,5.073 5.729,5.271 0.458,0.198 10 false VA4 5.271,4.844 5.729,5.042 0.458,0.198 10 false VA5 5.271,4.615 5.729,4.813 0.458,0.198 10 false VA6 5.281,4.385 5.74,4.583 0.458,0.198 10 false VA7 5.271,4.135 5.729,4.333 0.458,0.198 10 false VA8 5.271,3.896 5.729,4.094 0.458,0.198 10 false VA9 5.271,3.667 5.729,3.865 0.458,0.198 10 false VA10 5.271,3.438 5.729,3.635 0.458,0.198 10 false VA11 5.271,3.198 5.729,3.396 0.458,0.198 10 false VA12 5.271,2.958 5.729,3.156 0.458,0.198 10 false VA13 5.271,2.74 5.729,2.938 0.458,0.198 10 false VA14 5.271,2.49 5.729,2.688 0.458,0.198 10 false VA15 5.271,2.26 5.729,2.458 0.458,0.198 10 false VA16 5.271,2.021 5.729,2.219 0.458,0.198 10 false VA17 5.271,1.771 5.729,1.969 0.458,0.198 10 false VA18 5.271,1.51 5.729,1.708 0.458,0.198 10 false VA19 5.271,1.26 5.729,1.458 0.458,0.198 10 false VA20 5.271,1.042 5.729,1.24 0.458,0.198 10 false VA21 5.271,0.781 5.729,0.979 0.458,0.198 10 false VA22 3.573,0.677 4.031,0.875 0.458,0.198 10 false VA22 3.573,0.948 4.031,1.146 0.458,0.198 10 false VA21 3.573,1.177 4.031,1.375 0.458,0.198 10 false VA20 3.573,1.417 4.031,1.615 0.458,0.198 10 false VA19 3.573,1.667 4.031,1.865 0.458,0.198 10 false VA18 3.573,1.917 4.031,2.115 0.458,0.198 10 false VA17 3.573,2.156 4.031,2.354 0.458,0.198 10 false VA16 3.573,2.396 4.031,2.594 0.458,0.198 10 false VA15 3.573,2.625 4.031,2.823 0.458,0.198 10 false VA14 3.583,2.865 4.042,3.063 0.458,0.198 10 false VA13 3.583,3.125 4.042,3.323 0.458,0.198 10 false VA12 3.583,3.354 4.042,3.552 0.458,0.198 10 false VA11 3.583,3.594 4.042,3.792 0.458,0.198 10 false VA10 3.646,3.813 4.104,4.01 0.458,0.198 10 false VA9 3.646,4.052 4.104,4.25 0.458,0.198 10 false VA8 3.646,4.292 4.104,4.49 0.458,0.198 10 false VA7 3.646,4.521 4.104,4.719 0.458,0.198 10 false VA6 3.646,4.76 4.104,4.958 0.458,0.198 10 false VA5 3.635,4.99 4.094,5.188 0.458,0.198 10 false VA4 3.646,5.219 4.104,5.417 0.458,0.198 10 false VA3 3.646,5.458 4.104,5.656 0.458,0.198 10 false VA2 3.646,5.698 4.104,5.896 0.458,0.198 10 false VA1 3.635,5.917 4.094,6.115 0.458,0.198 10 false GA0 4.948,5.938 5.26,6.135 0.313,0.198 10 false 10 4.948,5.698 5.26,5.896 0.313,0.198 10 false 24 5.021,5.469 5.177,5.667 0.156,0.198 10 false 9 4.948,5.229 5.26,5.427 0.313,0.198 10 false 23 5.021,4.99 5.177,5.188 0.156,0.198 10 false 8 5.021,4.76 5.177,4.958 0.156,0.198 10 false 7 4.948,4.521 5.26,4.719 0.313,0.198 10 false 22 5.021,4.292 5.177,4.49 0.156,0.198 10 false 6 4.969,4.052 5.281,4.25 0.313,0.198 10 false 21 4.948,3.813 5.26,4.01 0.313,0.198 10 false 20 4.948,3.583 5.26,3.781 0.313,0.198 10 false 19 4.958,3.365 5.271,3.563 0.313,0.198 10 false 18 4.958,3.125 5.271,3.323 0.313,0.198 10 false 17 4.948,2.865 5.26,3.063 0.313,0.198 10 false 16 4.938,2.625 5.25,2.823 0.313,0.198 10 false 15 4.948,2.406 5.26,2.604 0.313,0.198 10 false 14 4.958,1.927 5.229,2.104 0.271,0.177 10 false 13 5.021,2.167 5.25,2.365 0.229,0.198 10 false 5 5.021,1.667 5.177,1.865 0.156,0.198 10 false 4 5.021,1.427 5.177,1.625 0.156,0.198 10 false 3 4.948,1.188 5.26,1.385 0.313,0.198 10 false 12 5.021,0.948 5.177,1.146 0.156,0.198 10 false 2 4.979,0.688 5.292,0.885 0.313,0.198 10 false 11 4.625,6.396 7.156,6.625 2.531,0.229 10 false Battery Voltage Sensor (for Upper Side) 4.635,6.219 5.094,6.417 0.458,0.198 10 false z14 1.49,6.396 5.156,6.594 3.667,0.198 10 false No. 1 EV Supply Stack Sub-assembly

C375132E07
5.271,0.802 5.885,1 0.615,0.198 10 false VA84 5.26,1.042 5.875,1.24 0.615,0.198 10 false VA83 5.271,1.271 5.885,1.469 0.615,0.198 10 false VA82 5.271,1.521 5.885,1.719 0.615,0.198 10 false VA81 5.271,1.75 5.885,1.948 0.615,0.198 10 false VA80 5.271,1.979 5.885,2.177 0.615,0.198 10 false VA79 5.271,2.208 5.885,2.406 0.615,0.198 10 false VA78 5.271,2.448 5.885,2.646 0.615,0.198 10 false VA77 5.271,2.677 5.885,2.875 0.615,0.198 10 false VA76 5.271,2.917 5.885,3.115 0.615,0.198 10 false VA75 5.281,3.146 5.896,3.344 0.615,0.198 10 false VA74 5.271,3.375 5.885,3.573 0.615,0.198 10 false VA73 5.271,3.615 5.885,3.813 0.615,0.198 10 false VA72 5.271,3.865 5.885,4.063 0.615,0.198 10 false VA71 5.271,4.094 5.885,4.292 0.615,0.198 10 false VA70 5.26,4.323 5.875,4.521 0.615,0.198 10 false VA69 5.271,4.573 5.885,4.771 0.615,0.198 10 false VA68 5.26,4.802 5.875,5 0.615,0.198 10 false VA67 5.271,5.042 5.885,5.24 0.615,0.198 10 false VA66 5.271,5.302 5.885,5.5 0.615,0.198 10 false VA65 5.281,5.552 5.74,5.75 0.458,0.198 10 false GA3 3.521,0.708 4.135,0.906 0.615,0.198 10 false VA84 3.521,0.958 4.135,1.156 0.615,0.198 10 false VA83 3.521,1.198 4.135,1.396 0.615,0.198 10 false VA82 3.531,1.417 4.146,1.615 0.615,0.198 10 false VA81 3.521,1.656 4.135,1.854 0.615,0.198 10 false VA80 3.521,1.885 4.135,2.083 0.615,0.198 10 false VA79 3.521,2.125 4.135,2.323 0.615,0.198 10 false VA78 3.521,2.354 4.135,2.552 0.615,0.198 10 false VA77 3.521,2.604 4.135,2.802 0.615,0.198 10 false VA76 3.521,2.844 4.135,3.042 0.615,0.198 10 false VA75 3.521,3.073 4.135,3.271 0.615,0.198 10 false VA74 3.521,3.292 4.135,3.49 0.615,0.198 10 false VA73 3.521,3.521 4.135,3.719 0.615,0.198 10 false VA72 3.521,3.771 4.135,3.969 0.615,0.198 10 false VA71 3.521,4.01 4.135,4.208 0.615,0.198 10 false VA70 3.521,4.24 4.135,4.438 0.615,0.198 10 false VA69 3.521,4.49 4.135,4.688 0.615,0.198 10 false VA68 3.521,4.708 4.135,4.906 0.615,0.198 10 false VA67 3.521,4.969 4.135,5.167 0.615,0.198 10 false VA66 3.521,5.219 4.135,5.417 0.615,0.198 10 false VA65 3.583,5.469 4.042,5.667 0.458,0.198 10 false GA3 5.021,0.708 5.177,0.906 0.156,0.198 10 false 1 4.948,0.948 5.26,1.146 0.313,0.198 10 false 11 5,1.167 5.156,1.365 0.156,0.198 10 false 2 4.927,1.396 5.24,1.594 0.313,0.198 10 false 12 5,1.635 5.156,1.833 0.156,0.198 10 false 3 5,1.875 5.156,2.073 0.156,0.198 10 false 4 4.927,2.125 5.24,2.323 0.313,0.198 10 false 13 5,2.354 5.156,2.552 0.156,0.198 10 false 5 4.927,2.573 5.24,2.771 0.313,0.198 10 false 14 4.927,2.813 5.24,3.01 0.313,0.198 10 false 15 4.927,3.052 5.24,3.25 0.313,0.198 10 false 16 4.927,3.292 5.24,3.49 0.313,0.198 10 false 17 4.927,3.531 5.24,3.729 0.313,0.198 10 false 18 4.927,3.771 5.24,3.969 0.313,0.198 10 false 19 4.938,4.01 5.25,4.208 0.313,0.198 10 false 20 4.948,4.24 5.26,4.438 0.313,0.198 10 false 21 5,4.49 5.156,4.688 0.156,0.198 10 false 6 4.927,4.719 5.24,4.917 0.313,0.198 10 false 22 5,4.958 5.156,5.156 0.156,0.198 10 false 7 5,5.219 5.156,5.417 0.156,0.198 10 false 8 4.927,5.458 5.24,5.656 0.313,0.198 10 false 23 1.51,6.385 5.177,6.583 3.667,0.198 10 false No. 2 EV Supply Stack Sub-assembly 4.521,6.083 7.156,6.323 2.635,0.24 10 false Battery Voltage Sensor (for Lower Side) 4.531,5.896 4.99,6.094 0.458,0.198 10 false z17

C375133E07
5.281,6.031 5.74,6.229 0.458,0.198 10 false GA2 5.271,5.792 5.729,5.99 0.458,0.198 10 false VA43 5.271,5.563 5.729,5.76 0.458,0.198 10 false VA44 5.271,5.333 5.729,5.531 0.458,0.198 10 false VA45 5.271,5.094 5.729,5.292 0.458,0.198 10 false VA46 5.271,4.854 5.729,5.052 0.458,0.198 10 false VA47 5.271,4.625 5.729,4.823 0.458,0.198 10 false VA48 5.281,4.396 5.74,4.594 0.458,0.198 10 false VA49 5.271,4.146 5.729,4.344 0.458,0.198 10 false VA50 5.271,3.917 5.729,4.115 0.458,0.198 10 false VA51 5.271,3.677 5.729,3.875 0.458,0.198 10 false VA52 5.271,3.448 5.729,3.646 0.458,0.198 10 false VA53 5.271,3.219 5.729,3.417 0.458,0.198 10 false VA54 5.271,2.969 5.729,3.167 0.458,0.198 10 false VA55 5.271,2.75 5.729,2.948 0.458,0.198 10 false VA56 5.271,2.51 5.729,2.708 0.458,0.198 10 false VA57 5.271,2.26 5.729,2.458 0.458,0.198 10 false VA58 5.271,2.031 5.729,2.229 0.458,0.198 10 false VA59 5.271,1.781 5.729,1.979 0.458,0.198 10 false VA60 5.271,1.521 5.729,1.719 0.458,0.198 10 false VA61 5.271,1.271 5.729,1.469 0.458,0.198 10 false VA62 5.271,1.042 5.729,1.24 0.458,0.198 10 false VA63 5.271,0.781 5.729,0.979 0.458,0.198 10 false VA64 3.573,0.708 4.031,0.906 0.458,0.198 10 false VA64 3.573,0.958 4.031,1.156 0.458,0.198 10 false VA63 3.583,1.188 4.042,1.385 0.458,0.198 10 false VA62 3.573,1.427 4.031,1.625 0.458,0.198 10 false VA61 3.573,1.677 4.031,1.875 0.458,0.198 10 false VA60 3.573,1.927 4.031,2.125 0.458,0.198 10 false VA59 3.573,2.167 4.031,2.365 0.458,0.198 10 false VA58 3.573,2.406 4.031,2.604 0.458,0.198 10 false VA57 3.573,2.635 4.031,2.833 0.458,0.198 10 false VA56 3.583,2.865 4.042,3.063 0.458,0.198 10 false VA55 3.583,3.125 4.042,3.323 0.458,0.198 10 false VA54 3.583,3.365 4.042,3.563 0.458,0.198 10 false VA53 3.583,3.594 4.042,3.792 0.458,0.198 10 false VA52 3.583,3.823 4.042,4.021 0.458,0.198 10 false VA51 3.583,4.063 4.042,4.26 0.458,0.198 10 false VA50 3.583,4.302 4.042,4.5 0.458,0.198 10 false VA49 3.583,4.531 4.042,4.729 0.458,0.198 10 false VA48 3.583,4.771 4.042,4.969 0.458,0.198 10 false VA47 3.573,5 4.031,5.198 0.458,0.198 10 false VA46 3.583,5.24 4.042,5.438 0.458,0.198 10 false VA45 3.583,5.458 4.042,5.656 0.458,0.198 10 false VA44 3.583,5.698 4.042,5.896 0.458,0.198 10 false VA43 3.635,5.938 4.094,6.135 0.458,0.198 10 false GA2 4.948,5.958 5.26,6.156 0.313,0.198 10 false 10 4.948,5.698 5.26,5.896 0.313,0.198 10 false 24 5.021,5.469 5.177,5.667 0.156,0.198 10 false 9 4.948,5.24 5.26,5.438 0.313,0.198 10 false 23 5.021,5 5.177,5.198 0.156,0.198 10 false 8 5.021,4.771 5.177,4.969 0.156,0.198 10 false 7 4.948,4.531 5.26,4.729 0.313,0.198 10 false 22 5.021,4.292 5.177,4.49 0.156,0.198 10 false 6 4.969,4.042 5.281,4.24 0.313,0.198 10 false 21 4.948,3.813 5.26,4.01 0.313,0.198 10 false 20 4.948,3.594 5.26,3.792 0.313,0.198 10 false 19 4.948,3.365 5.26,3.563 0.313,0.198 10 false 18 4.948,3.115 5.26,3.313 0.313,0.198 10 false 17 4.948,2.865 5.26,3.063 0.313,0.198 10 false 16 4.948,2.625 5.26,2.823 0.313,0.198 10 false 15 4.948,2.406 5.26,2.604 0.313,0.198 10 false 14 4.958,1.917 5.229,2.094 0.271,0.177 10 false 13 5.021,2.156 5.25,2.354 0.229,0.198 10 false 5 5.021,1.667 5.177,1.865 0.156,0.198 10 false 4 5.021,1.417 5.177,1.615 0.156,0.198 10 false 3 4.948,1.177 5.26,1.375 0.313,0.198 10 false 12 5.021,0.948 5.177,1.146 0.156,0.198 10 false 2 4.979,0.698 5.292,0.896 0.313,0.198 10 false 11 4.51,6.396 7.01,6.615 2.5,0.219 10 false Battery Voltage Sensor (for Lower Side) 4.51,6.219 4.969,6.417 0.458,0.198 10 false z16 1.49,6.396 5.156,6.594 3.667,0.198 10 false No. 2 EV Supply Stack Sub-assembly

C375134E03
2.073,8.313 4.677,8.51 2.604,0.198 10 false Battery Voltage Sensor (for Lower Side) 2.115,3.99 4.719,4.188 2.604,0.198 10 false Battery Voltage Sensor (for Upper Side) 1.865,3.99 2.177,4.188 0.313,0.198 10 false y1 1.813,8.313 2.125,8.51 0.313,0.198 10 false y3 4.844,8.271 5.156,8.469 0.313,0.198 10 false y2 5.094,8.271 6.656,8.51 1.563,0.24 10 false Battery ECU Assembly 5.229,0.5 5.688,0.698 0.458,0.198 10 false CIP 5.24,1.198 5.698,1.396 0.458,0.198 10 false DIP 3.24,0.844 3.698,1.042 0.458,0.198 10 false CIN0 3.24,1.531 3.698,1.729 0.458,0.198 10 false DIN0 5.25,1.844 5.708,2.042 0.458,0.198 10 false FB0 5.26,2.188 5.719,2.385 0.458,0.198 10 false FB1 5.24,2.531 5.698,2.729 0.458,0.198 10 false GFB0 5.24,2.875 5.698,3.073 0.458,0.198 10 false GFB1 5.25,3.208 5.708,3.406 0.458,0.198 10 false GA0 5.26,3.563 5.719,3.76 0.458,0.198 10 false VBB1 5.25,4.823 5.708,5.021 0.458,0.198 10 false COP 5.25,5.51 5.708,5.708 0.458,0.198 10 false DOP 5.25,5.167 5.708,5.365 0.458,0.198 10 false CON 5.25,5.844 5.708,6.042 0.458,0.198 10 false DON 5.26,6.188 5.719,6.385 0.458,0.198 10 false FB2 5.25,6.521 5.719,6.719 0.469,0.198 10 false FB3 5.229,6.865 5.688,7.063 0.458,0.198 10 false GFB2 5.229,7.219 5.688,7.417 0.458,0.198 10 false GFB3 5.24,7.552 5.698,7.75 0.458,0.198 10 false GA2 5.25,7.906 5.708,8.104 0.458,0.198 10 false VBB3 3.156,4.833 3.615,5.031 0.458,0.198 10 false COP3 3.156,5.177 3.615,5.375 0.458,0.198 10 false CON3 3.167,5.51 3.625,5.708 0.458,0.198 10 false DOP3 3.167,5.854 3.625,6.052 0.458,0.198 10 false DON3 3.271,6.188 3.729,6.385 0.458,0.198 10 false FB2 3.271,6.531 3.74,6.729 0.469,0.198 10 false FB3 3.177,6.875 3.635,7.073 0.458,0.198 10 false GFB2 3.167,7.219 3.625,7.417 0.458,0.198 10 false GFB3 3.229,7.552 3.688,7.75 0.458,0.198 10 false GA2 3.177,7.875 3.635,8.073 0.458,0.198 10 false VBB3 3.24,0.51 3.698,0.708 0.458,0.198 10 false CIP0 5.24,0.844 5.698,1.042 0.458,0.198 10 false CIN 3.24,1.198 3.698,1.396 0.458,0.198 10 false DIP0 5.25,1.51 5.708,1.708 0.458,0.198 10 false DIN 3.281,1.865 3.74,2.063 0.458,0.198 10 false FB0 3.281,2.208 3.74,2.406 0.458,0.198 10 false FB1 3.198,2.552 3.656,2.75 0.458,0.198 10 false GFB0 3.198,2.875 3.656,3.073 0.458,0.198 10 false GFB1 3.271,3.24 3.729,3.438 0.458,0.198 10 false GA0 3.208,3.563 3.667,3.76 0.458,0.198 10 false VBB1 2.365,2.271 2.979,2.469 0.615,0.198 10 false CON1 2.365,2.646 2.979,2.844 0.615,0.198 10 false COP1 2.375,3.01 2.99,3.208 0.615,0.198 10 false DON1 2.385,3.375 3,3.573 0.615,0.198 10 false DOP1 2.375,5.01 2.99,5.208 0.615,0.198 10 false DIP2 2.385,5.396 3,5.594 0.615,0.198 10 false DIN2 2.375,6.115 2.99,6.313 0.615,0.198 10 false CIP2 2.365,5.75 2.979,5.948 0.615,0.198 10 false G2DD 2.365,6.823 2.979,7.021 0.615,0.198 10 false G2DC 2.375,6.469 2.99,6.667 0.615,0.198 10 false CIN2 0.563,8.302 1.333,8.5 0.771,0.198 10 false : Shielded 4.917,0.417 5.229,0.615 0.313,0.198 10 false 20 4.906,1.083 5.219,1.281 0.313,0.198 10 false 38 4.906,0.74 5.219,0.938 0.313,0.198 10 false 40 4.906,1.427 5.219,1.625 0.313,0.198 10 false 18 4.906,1.771 5.219,1.969 0.313,0.198 10 false 36 4.906,2.115 5.219,2.313 0.313,0.198 10 false 34 4.906,2.448 5.219,2.646 0.313,0.198 10 false 16 4.917,2.792 5.229,2.99 0.313,0.198 10 false 14 4.917,3.125 5.229,3.323 0.313,0.198 10 false 17 4.906,3.479 5.219,3.677 0.313,0.198 10 false 32 3.698,0.406 4.01,0.604 0.313,0.198 10 false 20 3.708,0.75 4.021,0.948 0.313,0.198 10 false 22 3.708,1.094 4.021,1.292 0.313,0.198 10 false 23 3.708,1.427 4.021,1.625 0.313,0.198 10 false 25 3.719,1.76 4.031,1.958 0.313,0.198 10 false 27 3.708,2.115 4.021,2.313 0.313,0.198 10 false 31 3.698,2.448 4.01,2.646 0.313,0.198 10 false 26 3.698,2.792 4.01,2.99 0.313,0.198 10 false 30 3.698,3.135 4.01,3.333 0.313,0.198 10 false 19 3.708,3.479 4.021,3.677 0.313,0.198 10 false 34 2.042,2.156 2.354,2.354 0.313,0.198 10 false 37 3.719,4.729 4.031,4.927 0.313,0.198 10 false 38 2.031,2.906 2.344,3.104 0.313,0.198 10 false 39 2.031,3.281 2.344,3.479 0.313,0.198 10 false 40 2.01,5.615 2.323,5.813 0.313,0.198 10 false 24 2,6.688 2.313,6.885 0.313,0.198 10 false 21 2.01,4.875 2.323,5.073 0.313,0.198 10 false 23 2.01,5.229 2.323,5.427 0.313,0.198 10 false 25 2.01,5.979 2.323,6.177 0.313,0.198 10 false 20 2,6.333 2.313,6.531 0.313,0.198 10 false 22 4.938,4.74 5.25,4.938 0.313,0.198 10 false 3 3.719,5.073 4.031,5.271 0.313,0.198 10 false 37 3.729,5.417 4.042,5.615 0.313,0.198 10 false 40 3.729,5.76 4.042,5.958 0.313,0.198 10 false 39 3.729,6.094 4.042,6.292 0.313,0.198 10 false 27 3.74,6.438 4.052,6.635 0.313,0.198 10 false 31 3.729,6.781 4.042,6.979 0.313,0.198 10 false 26 3.74,7.125 4.052,7.323 0.313,0.198 10 false 30 3.729,7.458 4.042,7.656 0.313,0.198 10 false 19 3.729,7.802 4.042,8 0.313,0.198 10 false 34 4.938,5.083 5.25,5.281 0.313,0.198 10 false 1 4.875,5.406 5.188,5.604 0.313,0.198 10 false 21 4.885,5.76 5.198,5.958 0.313,0.198 10 false 23 4.875,6.438 5.188,6.635 0.313,0.198 10 false 28 4.875,6.094 5.188,6.292 0.313,0.198 10 false 30 4.927,7.115 5.24,7.313 0.313,0.198 10 false 8 4.865,6.771 5.177,6.969 0.313,0.198 10 false 10 4.865,7.448 5.177,7.646 0.313,0.198 10 false 12 4.854,7.792 5.167,7.99 0.313,0.198 10 false 26 2.031,2.531 2.344,2.729 0.313,0.198 10 false 38

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly is disposed of improperly or abandoned. Therefore, make sure to return all EV supply battery assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly to produce heat, resulting in a fire.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY, EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0E2D00 for Hybrid battery system is output A
P0E2D00 and DTCs other than the DTCs in the table below are output B
P0E2D00 and Hybrid battery system DTCs in the table below are output C
P0E2D00 and Hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure*1

*1: If area specific insulation resistance malfunction DTCs (P1C7C49, P1C7D49, P1C7E49, P1C7F49, P1EEC49, P1EED49, P1EEE49 or P1EEF49) are output, perform repairs according to each DTC.


Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA

C

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

D

2.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Lost Communication with Hybrid/EV Battery Monitoring IC", "Hybrid/EV Battery Monitoring IC 1 Internal Malfunction (Determinable)" through "Hybrid/EV Battery Monitoring IC 4 Internal Malfunction (Determinable)", "Hybrid/EV Battery Monitoring IC Internal Malfunction (Unidentifiable)", "Hybrid/EV Battery Monitoring IC 1 Power Supply Malfunction" through "Hybrid/EV Battery Monitoring IC 4 Power Supply Malfunction" and "Hybrid/EV Battery Monitoring IC 1 Cell Voltage Detection Malfunction" through "Hybrid/EV Battery Monitoring IC 4 Cell Voltage Detection Malfunction" for DTC P0E2D00 and make a note.

Powertrain > EV Battery > DTC(P0E2D00) > Freeze Frame Data
Tester Display
Lost Communication with Hybrid/EV Battery Monitoring IC
Hybrid/EV Battery Monitoring IC 1 Internal Malfunction (Determinable)
Hybrid/EV Battery Monitoring IC 2 Internal Malfunction (Determinable)
Hybrid/EV Battery Monitoring IC 3 Internal Malfunction (Determinable)
Hybrid/EV Battery Monitoring IC 4 Internal Malfunction (Determinable)
Hybrid/EV Battery Monitoring IC Internal Malfunction (Unidentifiable)
Hybrid/EV Battery Monitoring IC 1 Power Supply Malfunction
Hybrid/EV Battery Monitoring IC 2 Power Supply Malfunction
Hybrid/EV Battery Monitoring IC 3 Power Supply Malfunction
Hybrid/EV Battery Monitoring IC 4 Power Supply Malfunction
Hybrid/EV Battery Monitoring IC 1 Cell Voltage Detection Malfunction
Hybrid/EV Battery Monitoring IC 2 Cell Voltage Detection Malfunction
Hybrid/EV Battery Monitoring IC 3 Cell Voltage Detection Malfunction
Hybrid/EV Battery Monitoring IC 4 Cell Voltage Detection Malfunction
50040 398 541,545,544,543,542,540,549,548,547,546,553,552,551,550 P0E2D00

Result:
Result Proceed to
The freeze frame data item "Hybrid/EV Battery Monitoring IC Internal Malfunction (Unidentifiable)" is ON. A
Either freeze frame data item "Hybrid/EV Battery Monitoring IC 1 Internal Malfunction (Determinable)" or "Hybrid/EV Battery Monitoring IC 2 Internal Malfunction (Determinable)" is ON. B
Either freeze frame data item "Hybrid/EV Battery Monitoring IC 3 Internal Malfunction (Determinable)" or "Hybrid/EV Battery Monitoring IC 4 Internal Malfunction (Determinable)" is ON. C
Any of the freeze frame data items "Hybrid/EV Battery Monitoring IC 1 Power Supply Malfunction" through "Hybrid/EV Battery Monitoring IC 4 Power Supply Malfunction" is ON. D
The freeze frame data item "Lost Communication with Hybrid/EV Battery Monitoring IC" is ON. E
Any of the freeze frame data items "Hybrid/EV Battery Monitoring IC 1 Cell Voltage Detection Malfunction" through "Hybrid/EV Battery Monitoring IC 4 Cell Voltage Detection Malfunction" is ON. F


HINT:
·

The chart above is listed in inspection order of priority.

·

Check items that are ON at the same time by following the listed order.



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side) and BATTERY VOLTAGE SENSOR (for Lower Side)

B

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

C

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

D

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)

E

4.CLEAR DTC (EV BATTERY)

F

24.CHECK ODOMETER
3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



c.

Disconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
C373310N06
0.385,0.458 0.802,0.75 0.417,0.292 0.49,0.531 0.74,0.708 0.25,0.177 10 true y2

Disconnect the y2 battery ECU assembly connector.


NOTICE:
·

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

·

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



f.

Disconnect the y3 battery voltage sensor (for lower side) connector.

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C374919C32
1.469,0.177 1.917,0.479 0.448,0.302 1.51,2.375 1.958,2.677 0.448,0.302 0.958,1.156 1.115,0.49 true 1.26,2.083 0.938,1.448 true 1.26,1.135 2.281,0.406 true 1.906,2.063 1.208,1.448 true 2.104,4.292 2.135,3.448 true 1.438,4.313 2.021,3.469 true 0.74,4.323 1.667,3.469 true 0.781,2.667 1.542,3.385 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.677,2.49 1.99,2.688 0.313,0.198 10 false y1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.073,2.344 0.385,2.5 0.313,0.156 10 false *b 1,0.302 1.458,0.5 0.458,0.198 10 false GFB0 1.198,2.135 1.656,2.333 0.458,0.198 10 false FB0 2.365,0.302 2.823,0.5 0.458,0.198 10 false GFB1 1.906,2.125 2.365,2.323 0.458,0.198 10 false FB1 0.583,2.5 1.042,2.698 0.458,0.198 10 false FB1 0.51,4.385 0.969,4.583 0.458,0.198 10 false GFB1 1.323,4.385 1.781,4.583 0.458,0.198 10 false FB0 1.917,4.396 2.375,4.594 0.458,0.198 10 false GFB0
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y1)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

y2-16 (GFB0) - y1-26 (GFB0) Always Below 1 Ω
y2-36 (FB0) - y1-27 (FB0) Always Below 1 Ω
y2-14 (GFB1) - y1-30 (GFB1) Always Below 1 Ω
y2-34 (FB1) - y1-31 (FB1) Always Below 1 Ω



b.
C374919C33
1.469,0.177 1.917,0.479 0.448,0.302 1.51,2.375 1.958,2.677 0.448,0.302 2.177,3.375 2.958,2.823 true 1.771,1.115 1.104,0.396 true 2.052,2.083 2.073,1.448 true 1.594,2.094 1.781,1.438 true 2.083,1.135 2.156,0.458 true 2.26,2.802 1.677,3.396 true 1.948,4.219 1.573,3.448 true 2.5,4.229 2.052,3.458 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.677,2.49 1.99,2.688 0.313,0.198 10 false y3 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.073,2.344 0.385,2.5 0.313,0.156 10 false *b 1.958,2.135 2.417,2.333 0.458,0.198 10 false FB3 1.438,2.135 1.896,2.333 0.458,0.198 10 false FB2 0.729,0.292 1.188,0.49 0.458,0.198 10 false GFB2 2,0.302 2.458,0.5 0.458,0.198 10 false GFB3 2.167,2.635 2.625,2.833 0.458,0.198 10 false GFB3 1.854,4.302 2.313,4.5 0.458,0.198 10 false FB3 2.854,2.635 3.313,2.833 0.458,0.198 10 false GFB2 2.438,4.302 2.896,4.5 0.458,0.198 10 false FB2
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y3)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

y2-10 (GFB2) - y3-26 (GFB2) Always Below 1 Ω
y2-30 (FB2) - y3-27 (FB2) Always Below 1 Ω
y2-8 (GFB3) - y3-30 (GFB3) Always Below 1 Ω
y2-28 (FB3) - y3-31 (FB3) Always Below 1 Ω



Result:
Result Proceed to
OK Either recorded freeze frame data item "Hybrid/EV Battery Monitoring IC 1 Power Supply Malfunction" or "Hybrid/EV Battery Monitoring IC 2 Power Supply Malfunction" is ON. A
Either recorded freeze frame data item "Hybrid/EV Battery Monitoring IC 3 Power Supply Malfunction" or "Hybrid/EV Battery Monitoring IC 4 Power Supply Malfunction" is ON. B
NG C


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).



b.

Reconnect the y2 battery ECU assembly connector.


c.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




A

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side) and BATTERY ECU ASSEMBLY

B

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side) and BATTERY ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC (EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV Battery > Clear DTCs
50002 398

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

5.CHECK DTC OUTPUT (EV BATTERY)
5.CHECK DTC OUTPUT (EV BATTERY)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 1 minute or more.


Procedure1

a.

Check if DTCs are output.

Powertrain > EV Battery > Trouble Codes
50001 398

Result:
Result Proceed to
P0E2D00 is not output A
P0E2D00 is output B


Post-procedure1

a.

Turn the ignition switch off.



A

6.SIMULATION TEST

B

19.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)
6.SIMULATION TEST
NOTICE:

Do not turn the ignition switch off while performing this inspection.


Pre-procedure1

a.

None.


Procedure1

a.

With the vehicle stopped and the shift state in park (P), turn the ignition switch to ON and wait for at least 70 seconds.


b.

Turn the ignition switch to ON (READY) and without depressing the accelerator pedal, and while depressing the brake pedal, change the shift state to drive (D) and wait for 1 minute. (Step A)


c.

Drive the vehicle 0.5 m (1.6 ft.) forward and perform step A.


d.

Drive the vehicle another 0.5 m (1.6 ft.) forward and perform step A. Repeat this procedure 5 times (minimum total driving distance: 2 m (6.6 ft.)).


e.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
HINT:

Use the Data List item and/or freeze frame data item "Short Wave Highest Value" for reference.



Result:
Result Proceed to
P0AA649 is not output A
P0AA649 is output B


Post-procedure1

a.

Turn the ignition switch off.



A

7.CHECK ODOMETER

B

7.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

8.CHECK INVERTER WITH CONVERTER ASSEMBLY
8.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371871C03
0.021,0.01 0.344,0.25 0.323,0.24 12 true *A 0.021,2.5 0.354,2.719 0.333,0.219 12 true *B
*A for LHD
*B for RHD


Disconnect the No. 2 battery pack wire and FC air compressor motor cable assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



Procedure1

a.
C256334C07
0.479,1.563 1.198,1.365 true 0.302,1.521 0.615,1.677 0.313,0.156 10 *1
*1 High Voltage Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
High voltage terminal - Body ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection with the No. 2 battery pack wire and FC air compressor motor cable assembly disconnected from the inverter with converter assembly.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the No. 2 battery pack wire and FC air compressor motor cable assembly to the inverter with converter assembly.



OK

9.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (NO. 2 BATTERY PACK WIRE)

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

9.CHECK FCV WITH MOTOR TRANSAXLE ASSEMBLY (NO. 2 BATTERY PACK WIRE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371865C02
0.021,0.021 0.333,0.26 0.313,0.24 12 true *A 0.021,2.458 0.313,2.698 0.292,0.24 12 true *B
*A for LHD
*B for RHD


Disconnect the No. 2 battery pack wire from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

HINT:

As the insulation resistance may vary when motor (MG2) rotates, perform this inspection while rotating the rear wheels.



d.

Turn the ignition switch to ON.

NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Move the shift lever to select shift state neutral (N) and lift the vehicle.


Procedure1

a.
C371859C10
0.094,0.635 0.406,0.885 0.313,0.25 0.094,3.063 0.406,3.313 0.313,0.25 1.083,0.583 0.917,0.417 false 1.417,0.583 1.458,0.417 false 1.667,0.583 1.969,0.427 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.5,2.625 false 1.958,2.813 2.052,2.615 false 2.26,2.813 2.552,2.625 false 0.948,2.938 1.167,3.104 false 0.573,0.219 1.135,0.427 0.563,0.208 10 false 3 (R-U) 1.24,0.229 1.927,0.438 0.688,0.208 10 false 2 (R-V) 1.771,0.229 2.646,0.458 0.875,0.229 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.156,0.667 0.469,0.865 0.313,0.198 10 false O2 0.479,0.656 0.792,0.854 0.313,0.198 12 false *A 0.156,3.104 0.469,3.302 0.313,0.198 10 false O1 2.375,2.427 2.948,2.635 0.573,0.208 10 false 1 (R-U) 1.823,2.427 2.354,2.625 0.531,0.198 10 false 2 (R-V) 1.208,2.427 1.74,2.615 0.531,0.188 10 false 3 (R-W) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.479,3.094 0.792,3.292 0.313,0.198 12 false *B
*A for LHD
*B for RHD
*1 Shield Ground
*a No. 2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the rear wheels 2 revolutions in the same direction simultaneously.

NOTICE:
·

Carefully perform this inspection as the motor (MG2) may generate current when the rear wheels are rotated by hand.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-3 (R-U) - Body ground and shield ground Ignition switch ON 100 MΩ or higher
O2-2 (R-V) - Body ground and shield ground Ignition switch ON 100 MΩ or higher
O2-1 (R-W) - Body ground and shield ground Ignition switch ON 100 MΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-3 (R-W) - Body ground and shield ground Ignition switch ON 100 MΩ or higher
O1-2 (R-V) - Body ground and shield ground Ignition switch ON 100 MΩ or higher
O1-1 (R-U) - Body ground and shield ground Ignition switch ON 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Lower the vehicle and push the P position switch (parking switch).


b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


d.

Reconnect the No. 2 battery pack wire to the inverter with converter assembly.



OK

10.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY)

NG

15.CHECK NO. 2 BATTERY PACK WIRE
10.CHECK FC AIR COMPRESSOR WITH MOTOR ASSEMBLY (FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371868C02
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Disconnect the FC air compressor motor cable assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



Procedure1

a.
C371862C07
0.26,0.885 0.594,1.115 0.333,0.229 0.333,3.063 0.698,3.292 0.365,0.229 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.333,0.917 0.583,1.115 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable Assembly
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-1 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o3-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o3-3 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-3 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o2-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o2-1 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the FC air compressor motor cable assembly to the inverter with converter assembly.



OK

11.CHECK FC COOLING WATER PUMP ASSEMBLY (FC COOLING WATER PUMP CABLE)

NG

17.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
11.CHECK FC COOLING WATER PUMP ASSEMBLY (FC COOLING WATER PUMP CABLE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479485

Disconnect the FC cooling water pump cable from the FC converter assembly.


Procedure1

a.
A341477C09
0.438,0.969 0.875,1.292 0.438,0.323 2.375,1.667 1.99,1.208 true 1.74,1.698 1.719,1.219 true 1.104,1.667 1.448,1.219 true 2.833,0.469 1.865,0.885 true 2.396,1.729 2.552,1.927 0.156,0.198 10 false U 1.031,1.729 1.188,1.927 0.156,0.198 10 false W 1.708,1.729 1.865,1.927 0.156,0.198 10 false V 0.146,0.115 0.354,0.302 0.208,0.188 10 false *a 0.604,1.063 0.917,1.271 0.313,0.208 10 false b1 2.927,0.385 3.135,0.573 0.208,0.188 10 false *1
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the FC cooling water pump cable to the FC converter assembly.



OK

12.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY

NG

18.CHECK FC COOLING WATER PUMP CABLE
12.CHECK HYDROGEN RECIRCULATION PUMP ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479487

Disconnect the z30 hydrogen recirculation pump assembly connector.


Procedure1

a.
A481494C01
0.49,0.906 0.906,1.24 0.417,0.333 1.229,1.635 1.448,1.188 true 1.74,1.698 1.698,1.208 true 2.177,1.646 1.99,1.188 true 1.146,1.677 1.302,1.875 0.156,0.198 10 false U 1.688,1.729 1.844,1.927 0.156,0.198 10 false V 2.188,1.698 2.344,1.896 0.156,0.198 10 false W 0.188,0.167 0.417,0.375 0.229,0.208 10 false *a 0.615,1 1.01,1.24 0.396,0.24 10 false z30
*a Hydrogen Recirculation Pump Assembly Connector
(to FC Converter Assembly)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z30)Location & Routing

Click Connector(z30)Engine Compartment>other>FC Converter Assembly , Hydrogen Recirculation Pump Assembly

z30-1 (U) - Body ground Ignition switch off 10 MΩ or higher
z30-2 (V) - Body ground Ignition switch off 10 MΩ or higher
z30-3 (W) - Body ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the z30 hydrogen recirculation pump assembly connector.



OK

13.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

NG

REPLACE HYDROGEN RECIRCULATION PUMP ASSEMBLY

13.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373311N02
0.833,0.042 1.271,0.333 0.438,0.292 0.063,1.25 0.5,1.542 0.438,0.292 0.906,0.115 1.208,0.281 0.302,0.167 10 true z14 0.167,1.323 0.427,1.5 0.26,0.177 10 true z15

Check the connections of the z14 and z15 battery voltage sensor (for upper side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z14 or z15 was not connected securely The terminals are damaged or corroded C


Post-procedure1

a.

None.



A

14.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)

B

CONNECT SECURELY

C

20.CHECK TOTAL DISTANCE DRIVEN
14.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373312N02
0.74,0.063 1.177,0.323 0.438,0.26 0.073,1.292 0.51,1.552 0.438,0.26 0.833,0.125 1.135,0.292 0.302,0.167 10 true z16 0.156,1.333 0.427,1.521 0.271,0.188 10 true z17

Check the connections of the z16 and z17 battery voltage sensor (for lower side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z16 or z17 was not connected securely The terminals are damaged or corroded C



Post-procedure1

a.

None.



A

19.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)

B

CONNECT SECURELY

C

21.CHECK TOTAL DISTANCE DRIVEN
15.CHECK NO. 2 BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371865C02
0.021,0.021 0.333,0.26 0.313,0.24 12 true *A 0.021,2.458 0.313,2.698 0.292,0.24 12 true *B
*A for LHD
*B for RHD


Disconnect the No. 2 battery pack wire from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



c.
A480837

Disconnect the motor cable from the No. 2 battery pack wire.

HINT:

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>REMOVAL



Procedure1

a.
C371859C10
0.094,0.635 0.406,0.885 0.313,0.25 0.094,3.063 0.406,3.313 0.313,0.25 1.083,0.583 0.917,0.417 false 1.417,0.583 1.458,0.417 false 1.667,0.583 1.969,0.427 false 2.406,0.698 2.24,0.844 false 1.667,2.813 1.5,2.625 false 1.958,2.813 2.052,2.615 false 2.26,2.813 2.552,2.625 false 0.948,2.938 1.167,3.104 false 0.573,0.219 1.135,0.427 0.563,0.208 10 false 3 (R-U) 1.24,0.229 1.927,0.438 0.688,0.208 10 false 2 (R-V) 1.771,0.229 2.646,0.458 0.875,0.229 10 false 1 (R-W) 2.417,0.563 2.635,0.75 0.219,0.188 10 false *1 0.083,0.094 0.302,0.281 0.219,0.188 10 false *a 0.156,0.667 0.469,0.865 0.313,0.198 10 false O2 0.479,0.656 0.792,0.854 0.313,0.198 12 false *A 0.156,3.104 0.469,3.302 0.313,0.198 10 false O1 2.375,2.427 2.948,2.635 0.573,0.208 10 false 1 (R-U) 1.823,2.427 2.354,2.625 0.531,0.198 10 false 2 (R-V) 1.208,2.427 1.74,2.615 0.531,0.188 10 false 3 (R-W) 0.729,2.792 0.948,2.979 0.219,0.188 10 false *1 0.479,3.094 0.792,3.292 0.313,0.198 12 false *B
*A for LHD
*B for RHD
*1 Shield Ground
*a No. 2 Battery Pack Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(O2)Location & Routing

Click Connector(O2)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O2-3 (R-U) - Body ground and shield ground Ignition switch off 100 MΩ or higher
O2-2 (R-V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
O2-1 (R-W) - Body ground and shield ground Ignition switch off 100 MΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(O1)Location & Routing

Click Connector(O1)Engine Compartment>EV Battery Pack Wire>Inverter with Converter Assembly

O1-3 (R-W) - Body ground and shield ground Ignition switch off 100 MΩ or higher
O1-2 (R-V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
O1-1 (R-U) - Body ground and shield ground Ignition switch off 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the motor cable to the No. 2 battery pack wire.


b.

Reconnect the No. 2 battery pack wire to the inverter with converter assembly.



OK

16.CHECK MOTOR CABLE

NG

REPLACE NO. 2 BATTERY PACK WIRE

16.CHECK MOTOR CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A480837

Disconnect the motor cable wire from the No. 2 battery pack wire.

HINT:

Click hereSuspension>REAR SUSPENSION>REAR SUSPENSION MEMBER>REMOVAL



c.
A480836

Remove the motor cable from the FCV with motor transaxle assembly.

HINT:

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

a.
A479526C01
1.438,0.115 1.917,0.406 0.479,0.292 1.927,1.854 1.75,1.646 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.854,1.896 2.167,2.094 0.313,0.198 10 false *1 1.604,0.188 1.917,0.385 0.313,0.198 10 false q2
*1 Shield Ground
*a Motor Cable
(No. 2 Battery Pack Wire Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(q2)Location & Routing

Click Connector(q2)Body>Motor Cable>Shortcut Connector

q2-1 - Body ground and shield ground Ignition switch off 100 MΩ or higher
q2-2 - Body ground and shield ground Ignition switch off 100 MΩ or higher
q2-3 - Body ground and shield ground Ignition switch off 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the motor cable to the FCV with motor transaxle assembly.


b.

Reconnect the motor cable to the No. 2 battery pack wire.



OK

NG

17.CHECK FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
C371868C02
0.021,0.021 0.354,0.24 0.333,0.219 12 true *A 0.021,2.458 0.333,2.688 0.313,0.229 12 true *B
*A for LHD
*B for RHD


Disconnect the FC air compressor motor cable assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



c.
A480840

Remove the FC air compressor motor cable assembly from the FC air compressor with motor assembly.

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR COMPRESSOR>REMOVAL



Procedure1

a.
C371862C07
0.26,0.885 0.594,1.115 0.333,0.229 0.333,3.063 0.698,3.292 0.365,0.229 1.125,0.438 1.323,0.635 false 1.5,0.438 1.625,0.625 false 1.833,0.438 1.938,0.625 false 0.781,1.042 0.667,1.219 false 1.313,2.583 1.417,2.75 false 1.656,2.573 1.75,2.76 false 1.969,2.563 2.052,2.74 false 2.792,3.333 2.635,3.198 false 0.198,0.25 0.531,0.438 0.333,0.188 12 false *A 0.26,2.281 0.615,2.521 0.354,0.24 12 false *B 0.563,1.24 0.875,1.396 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.896,0.26 1.281,0.458 0.385,0.198 10 false 1 (U) 1.354,0.26 1.74,0.458 0.385,0.198 10 false 2 (V) 1.76,0.26 2.146,0.458 0.385,0.198 10 false 3 (W) 1.854,2.385 2.24,2.583 0.385,0.198 10 false 3 (U) 1.073,2.385 1.458,2.583 0.385,0.198 10 false 1 (W) 1.479,2.385 1.865,2.583 0.385,0.198 10 false 2 (V) 2.76,3.385 3.073,3.542 0.313,0.156 10 false *1 0.333,0.917 0.583,1.115 0.25,0.198 10 false o3 0.427,3.094 0.677,3.292 0.25,0.198 10 false o2
*A for LHD
*B for RHD
*1 Shield Ground
*a FC Air Compressor Motor Cable Assembly
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(o3)Location & Routing

Click Connector(o3)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o3-1 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o3-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o3-3 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(o2)Location & Routing

Click Connector(o2)Engine Compartment>FC Air Compressor Motor Cable Assembly>Inverter with Converter Assembly

o2-3 (U) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o2-2 (V) - Body ground and shield ground Ignition switch off 100 MΩ or higher
o2-1 (W) - Body ground and shield ground Ignition switch off 100 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air compressor motor cable assembly to the FC air compressor with motor assembly.


b.

Reconnect the FC air compressor motor cable assembly to the inverter with converter assembly.



OK

REPLACE FC AIR COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE FC AIR COMPRESSOR MOTOR CABLE ASSEMBLY

18.CHECK FC COOLING WATER PUMP CABLE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A479485

Disconnect the FC cooling water pump cable from the FC converter assembly.


c.
A480831

Disconnect the FC cooling water pump cable from the FC cooling water pump assembly.


Procedure1

a.
A341477C09
0.438,0.969 0.875,1.292 0.438,0.323 2.375,1.667 1.99,1.208 true 1.74,1.698 1.719,1.219 true 1.104,1.667 1.448,1.219 true 2.833,0.469 1.865,0.885 true 2.396,1.729 2.552,1.927 0.156,0.198 10 false U 1.031,1.729 1.188,1.927 0.156,0.198 10 false W 1.708,1.729 1.865,1.927 0.156,0.198 10 false V 0.146,0.115 0.354,0.302 0.208,0.188 10 false *a 0.604,1.063 0.917,1.271 0.313,0.208 10 false b1 2.927,0.385 3.135,0.573 0.208,0.188 10 false *1
*1 Shield Ground
*a FC Cooling Water Pump Cable
(FC Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b1)Location & Routing

Click Connector(b1)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b1-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-2 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b1-3 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the FC cooling water pump cable to the FC converter assembly.


b.

Reconnect the FC cooling water pump cable to the FC cooling water pump assembly.



OK

REPLACE FC COOLING WATER PUMP ASSEMBLY

NG

FC COOLING WATER PUMP CABLE

19.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY VOLTAGE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



c.

Disconnect the y1 battery voltage sensor (for upper side) connector.

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
C373310N06
0.385,0.458 0.802,0.75 0.417,0.292 0.49,0.531 0.74,0.708 0.25,0.177 10 true y2

Disconnect the y2 battery ECU assembly connector.


NOTICE:
·

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

·

Before disconnecting the connector, check that it is not loose or disconnected.



e.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



f.

Disconnect the y3 battery voltage sensor (for lower side) connector.

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C374919C34
1.469,0.177 1.917,0.479 0.448,0.302 1.51,2.375 1.958,2.677 0.448,0.302 2.271,3.396 2.469,2.688 true 0.656,1.146 0.646,0.51 true 0.792,1.969 0.667,1.448 true 0.354,1.979 0.365,1.458 true 0.396,1.135 0.26,0.521 true 0.958,1.156 1.115,0.49 true 1.26,2.083 0.938,1.448 true 1.26,1.135 2.281,0.406 true 1.906,2.063 1.208,1.448 true 2.573,4.302 2.5,3.448 true 3.073,4.281 2.74,3.469 true 2.979,3.385 2.979,2.667 true 2.104,4.292 2.135,3.448 true 1.438,4.313 2.021,3.469 true 0.74,4.323 1.667,3.469 true 0.781,2.667 1.542,3.385 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.677,2.49 1.99,2.688 0.313,0.198 10 false y1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.073,2.344 0.385,2.5 0.313,0.156 10 false *b 0.563,0.313 1.021,0.51 0.458,0.198 10 false DIN 2.969,4.365 3.427,4.563 0.458,0.198 10 false CIN0 0.719,2.031 1.177,2.229 0.458,0.198 10 false DIP 0.25,2.042 0.708,2.24 0.458,0.198 10 false CIN 0.094,0.313 0.552,0.51 0.458,0.198 10 false CIP 1,0.302 1.458,0.5 0.458,0.198 10 false GFB0 1.198,2.135 1.656,2.333 0.458,0.198 10 false FB0 2.365,0.302 2.823,0.5 0.458,0.198 10 false GFB1 1.906,2.125 2.365,2.323 0.458,0.198 10 false FB1 2.344,2.469 2.802,2.667 0.458,0.198 10 false DIN0 2.885,2.469 3.344,2.667 0.458,0.198 10 false CIP0 0.583,2.5 1.042,2.698 0.458,0.198 10 false FB1 0.51,4.385 0.969,4.583 0.458,0.198 10 false GFB1 1.323,4.385 1.781,4.583 0.458,0.198 10 false FB0 1.917,4.396 2.375,4.594 0.458,0.198 10 false GFB0 2.479,4.385 2.938,4.583 0.458,0.198 10 false DIP0
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Upper Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y1)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

y2-18 (DIN) - y1-25 (DIN0) Always Below 1 Ω
y2-38 (DIP) - y1-23 (DIP0) Always Below 1 Ω
y2-40 (CIN) - y1-22 (CIN0) Always Below 1 Ω
y2-20 (CIP) - y1-20 (CIP0) Always Below 1 Ω
y2-16 (GFB0) - y1-26 (GFB0) Always Below 1 Ω
y2-36 (FB0) - y1-27 (FB0) Always Below 1 Ω
y2-14 (GFB1) - y1-30 (GFB1) Always Below 1 Ω
y2-34 (FB1) - y1-31 (FB1) Always Below 1 Ω



b.
C374919C39
1.469,0.177 1.917,0.479 0.448,0.302 1.51,2.375 1.958,2.677 0.448,0.302 2.177,3.375 2.958,2.823 true 1.771,1.115 1.104,0.396 true 2.052,2.083 2.073,1.448 true 1.594,2.094 1.781,1.438 true 3.073,1.135 3.198,0.458 true 2.083,1.135 2.156,0.458 true 2.719,2.125 2.771,1.448 true 2.781,1.146 2.677,0.469 true 3.156,2.125 3.052,1.458 true 2.26,2.802 1.677,3.396 true 1.948,4.219 1.573,3.448 true 2.5,4.229 2.052,3.458 true 0.75,3.375 0.781,2.771 true 0.677,4.25 0.635,3.458 true 0.219,4.24 0.396,3.469 true 0.281,2.781 0.5,3.365 true 1.646,0.271 1.958,0.469 0.313,0.198 10 false y2 1.677,2.49 1.99,2.688 0.313,0.198 10 false y3 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.073,2.344 0.385,2.5 0.313,0.156 10 false *b 2.542,0.292 3,0.49 0.458,0.198 10 false COP 0.031,4.313 0.49,4.51 0.458,0.198 10 false DOP3 1.958,2.135 2.417,2.333 0.458,0.198 10 false FB3 1.438,2.135 1.896,2.333 0.458,0.198 10 false FB2 3.083,0.281 3.427,0.469 0.344,0.188 10 false CON 0.729,0.292 1.188,0.49 0.458,0.198 10 false GFB2 2.594,2.188 3.052,2.385 0.458,0.198 10 false DON 2,0.302 2.458,0.5 0.458,0.198 10 false GFB3 3.042,2.188 3.427,2.417 0.385,0.229 10 false DOP 0.531,4.313 0.99,4.51 0.458,0.198 10 false COP3 0.667,2.615 1.125,2.813 0.458,0.198 10 false CON3 0.094,2.604 0.552,2.802 0.458,0.198 10 false DON3 2.167,2.635 2.625,2.833 0.458,0.198 10 false GFB3 1.854,4.302 2.313,4.5 0.458,0.198 10 false FB3 2.854,2.635 3.313,2.833 0.458,0.198 10 false GFB2 2.438,4.302 2.896,4.5 0.458,0.198 10 false FB2
*a Component without harness connected
(to Battery ECU Assembly)
*b Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y2,y3)Location & Routing

Click Connector(y2)Body>No. 1 EV Battery Pack Wire>Battery ECU Assembly

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

y2-1 (CON) - y3-37 (CON3) Always Below 1 Ω
y2-3 (COP) - y3-38 (COP3) Always Below 1 Ω
y2-23 (DON) - y3-39 (DON3) Always Below 1 Ω
y2-21 (DOP) - y3-40 (DOP3) Always Below 1 Ω
y2-10 (GFB2) - y3-26 (GFB2) Always Below 1 Ω
y2-30 (FB2) - y3-27 (FB2) Always Below 1 Ω
y2-8 (GFB3) - y3-30 (GFB3) Always Below 1 Ω
y2-28 (FB3) - y3-31 (FB3) Always Below 1 Ω



c.
C374920C06
1.531,2.406 1.948,2.688 0.417,0.281 1.531,0.125 1.927,0.417 0.396,0.292 2.75,3.396 2.958,2.604 true 2.938,4.313 2.958,3.458 true 2.26,3.406 2.448,2.583 true 0.75,1.073 0.99,0.479 true 2.313,4.323 2.469,3.469 true 0.385,1.167 0.26,1.917 true 0.531,1.073 0.375,0.469 true 0.948,1.906 0.646,1.156 true 1.667,0.208 1.979,0.406 0.313,0.198 10 false y1 1.667,2.479 1.979,2.677 0.313,0.198 10 false y3 0.854,0.302 1.469,0.5 0.615,0.198 10 false CON1 0.854,1.979 1.469,2.177 0.615,0.198 10 false COP1 0.24,0.302 0.854,0.5 0.615,0.198 10 false DON1 0.125,2 0.74,2.198 0.615,0.198 10 false DOP1 2.896,2.385 3.302,2.583 0.406,0.198 10 false CIN2 2.833,4.375 3.323,4.604 0.49,0.229 10 false CIP2 2.302,2.385 2.917,2.583 0.615,0.198 10 false DIN2 2.188,4.385 2.802,4.583 0.615,0.198 10 false DIP2 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.115,2.375 0.427,2.531 0.313,0.156 10 false *b
*a Component without harness connected
(to Battery Voltage Sensor (for Upper Side))
*b Component without harness connected
(to Battery Voltage Sensor (for Lower Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(y1,y3)Location & Routing

Click Connector(y1)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Upper)

Click Connector(y3)Body>No. 1 EV Battery Pack Wire>Battery Voltage Sensor (Lower)

y1-37 (CON1) - y3-22 (CIN2) Always Below 1 Ω
y1-38 (COP1) - y3-20 (CIP2) Always Below 1 Ω
y1-39 (DON1) - y3-25 (DIN2) Always Below 1 Ω
y1-40 (DOP1) - y3-23 (DIP2) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).



b.

Reconnect the y2 battery ECU assembly connector.


c.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




OK

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side), BATTERY VOLTAGE SENSOR (for Lower Side) and BATTERY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

22.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
21.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

23.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
22.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

23.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

24.CHECK ODOMETER
a.

Check and record the total distance traveled of the vehicle.


Result:
Proceed to
NEXT



NEXT

25.CHECK FREEZE FRAME DATA
25.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

a.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 84 Voltage" for DTC P0E2D00 and make a note if the value of any is 1.6 V or less.

HINT:

Use this for reference when measuring the EV battery cell voltage.


Powertrain > EV Battery > DTC(P0E2D00) > Freeze Frame Data
Tester Display
Hybrid/EV Battery Cell 1 Voltage
Hybrid/EV Battery Cell 2 Voltage
Hybrid/EV Battery Cell 3 Voltage
Hybrid/EV Battery Cell 4 Voltage
Hybrid/EV Battery Cell 5 Voltage
Hybrid/EV Battery Cell 6 Voltage
Hybrid/EV Battery Cell 7 Voltage
Hybrid/EV Battery Cell 8 Voltage
Hybrid/EV Battery Cell 9 Voltage
Hybrid/EV Battery Cell 10 Voltage
Hybrid/EV Battery Cell 11 Voltage
Hybrid/EV Battery Cell 12 Voltage
Hybrid/EV Battery Cell 13 Voltage
Hybrid/EV Battery Cell 14 Voltage
Hybrid/EV Battery Cell 15 Voltage
Hybrid/EV Battery Cell 16 Voltage
Hybrid/EV Battery Cell 17 Voltage
Hybrid/EV Battery Cell 18 Voltage
Hybrid/EV Battery Cell 19 Voltage
Hybrid/EV Battery Cell 20 Voltage
Hybrid/EV Battery Cell 21 Voltage
Hybrid/EV Battery Cell 22 Voltage
Hybrid/EV Battery Cell 23 Voltage
Hybrid/EV Battery Cell 24 Voltage
Hybrid/EV Battery Cell 25 Voltage
Hybrid/EV Battery Cell 26 Voltage
Hybrid/EV Battery Cell 27 Voltage
Hybrid/EV Battery Cell 28 Voltage
Hybrid/EV Battery Cell 29 Voltage
Hybrid/EV Battery Cell 30 Voltage
Hybrid/EV Battery Cell 31 Voltage
Hybrid/EV Battery Cell 32 Voltage
Hybrid/EV Battery Cell 33 Voltage
Hybrid/EV Battery Cell 34 Voltage
Hybrid/EV Battery Cell 35 Voltage
Hybrid/EV Battery Cell 36 Voltage
Hybrid/EV Battery Cell 37 Voltage
Hybrid/EV Battery Cell 38 Voltage
Hybrid/EV Battery Cell 39 Voltage
Hybrid/EV Battery Cell 40 Voltage
Hybrid/EV Battery Cell 41 Voltage
Hybrid/EV Battery Cell 42 Voltage
Hybrid/EV Battery Cell 43 Voltage
Hybrid/EV Battery Cell 44 Voltage
Hybrid/EV Battery Cell 45 Voltage
Hybrid/EV Battery Cell 46 Voltage
Hybrid/EV Battery Cell 47 Voltage
Hybrid/EV Battery Cell 48 Voltage
Hybrid/EV Battery Cell 49 Voltage
Hybrid/EV Battery Cell 50 Voltage
Hybrid/EV Battery Cell 51 Voltage
Hybrid/EV Battery Cell 52 Voltage
Hybrid/EV Battery Cell 53 Voltage
Hybrid/EV Battery Cell 54 Voltage
Hybrid/EV Battery Cell 55 Voltage
Hybrid/EV Battery Cell 56 Voltage
Hybrid/EV Battery Cell 57 Voltage
Hybrid/EV Battery Cell 58 Voltage
Hybrid/EV Battery Cell 59 Voltage
Hybrid/EV Battery Cell 60 Voltage
Hybrid/EV Battery Cell 61 Voltage
Hybrid/EV Battery Cell 62 Voltage
Hybrid/EV Battery Cell 63 Voltage
Hybrid/EV Battery Cell 64 Voltage
Hybrid/EV Battery Cell 65 Voltage
Hybrid/EV Battery Cell 66 Voltage
Hybrid/EV Battery Cell 67 Voltage
Hybrid/EV Battery Cell 68 Voltage
Hybrid/EV Battery Cell 69 Voltage
Hybrid/EV Battery Cell 70 Voltage
Hybrid/EV Battery Cell 71 Voltage
Hybrid/EV Battery Cell 72 Voltage
Hybrid/EV Battery Cell 73 Voltage
Hybrid/EV Battery Cell 74 Voltage
Hybrid/EV Battery Cell 75 Voltage
Hybrid/EV Battery Cell 76 Voltage
Hybrid/EV Battery Cell 77 Voltage
Hybrid/EV Battery Cell 78 Voltage
Hybrid/EV Battery Cell 79 Voltage
Hybrid/EV Battery Cell 80 Voltage
Hybrid/EV Battery Cell 81 Voltage
Hybrid/EV Battery Cell 82 Voltage
Hybrid/EV Battery Cell 83 Voltage
Hybrid/EV Battery Cell 84 Voltage
50040 398 334,335,336,337,338,339,340,341,342,343,344,345,346,347,348,349,350,351,352,353,354,355,356,357,358,359,360,361,362,363,364,365,366,367,368,369,370,371,372,373,374,375,376,377,378,379,380,381,382,383,384,385,386,387,388,389,390,391,392,393,394,395,396,397,398,399,400,401,402,403,404,405,406,407,408,409,410,411,412,413,414,415,416,417 P0E2D00

Result:
Result Proceed to
The value of any of the freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 42 Voltage" is 1.6 V or less. A
The value of any of the freeze frame data items "Hybrid/EV Battery Cell 43 Voltage" through "Hybrid/EV Battery Cell 84 Voltage" is 1.6 V or less. B
Other than above Either freeze frame data item recorded "Hybrid/EV Battery Monitoring IC 1 Cell Voltage Detection Malfunction" or "Hybrid/EV Battery Monitoring IC 2 Cell Voltage Detection Malfunction" is ON. C
Either freeze frame data item recorded "Hybrid/EV Battery Monitoring IC 3 Cell Voltage Detection Malfunction" or "Hybrid/EV Battery Monitoring IC 4 Cell Voltage Detection Malfunction" is ON. D


Post-procedure1

a.

Turn the ignition switch off.



A

26.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

B

37.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)

C

48.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)

D

51.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)
26.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373311N03
0.865,0.042 1.26,0.333 0.396,0.292 0.104,1.281 0.49,1.542 0.385,0.26 0.938,0.115 1.229,0.281 0.292,0.167 10 true z14 0.177,1.323 0.438,1.5 0.26,0.177 10 true z15

Check the connections of the z14 and z15 battery voltage sensor (for upper side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z14 or z15 was not connected securely The terminals are damaged or corroded C



Post-procedure1

a.

None.



A

27.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

31.CHECK TOTAL DISTANCE DRIVEN
27.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the EV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each EV battery cell.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.

The value of any of the freeze frame data items "Hybrid/EV Battery Cell 1 Voltage" through "Hybrid/EV Battery Cell 22 Voltage" is 1.6 V or less.

i.
C373313N02
0.823,0.083 1.198,0.385 0.375,0.302 0.865,0.146 1.156,0.333 0.292,0.188 10 true z14

Disconnect the z14 battery voltage sensor (for upper side) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



ii.
C371966C07
1.531,1.292 1.938,1.521 0.406,0.229 0.656,2.688 0.375,2.396 true 2.208,2.677 1.99,1.865 true 0.781,2.667 0.479,2.094 true 0.885,2.688 0.677,1.854 true 1.031,2.688 1.021,2.073 true 1.188,2.656 1.323,1.844 true 2.281,4.271 2.031,2.865 true 2.354,2.667 2.344,2.073 true 2.615,2.667 2.948,2.083 true 2.479,2.667 2.75,1.833 true 3.021,3.333 2.698,2.865 true 2.948,3.771 2.542,2.865 true 2.583,3.573 2.313,2.854 true 2.469,3.979 2.167,2.865 true 2,4 1.896,2.854 true 1.75,4.271 1.729,2.854 true 1.573,4.031 1.635,2.844 true 0.833,3.594 1.104,2.844 true 1.146,4 1.344,2.844 true 0.896,4.24 1.229,2.844 true 1.323,4.26 1.521,2.854 true 0.531,3.76 0.844,2.854 true 0.354,3.365 0.698,2.865 true 2.5,3.646 2.896,3.813 0.396,0.167 10 false VA17 0.094,2.229 0.49,2.396 0.396,0.167 10 false GA0 0.354,1.896 0.75,2.063 0.396,0.167 10 false VA2 0.51,1.646 0.906,1.813 0.396,0.167 10 false VA4 0.885,1.885 1.281,2.052 0.396,0.167 10 false VA5 1.208,1.635 1.604,1.802 0.396,0.167 10 false VA7 1.792,1.667 2.188,1.833 0.396,0.167 10 false VA16 2.885,1.896 3.281,2.063 0.396,0.167 10 false VA21 2.615,1.635 3.01,1.802 0.396,0.167 10 false VA19 2.208,1.885 2.604,2.052 0.396,0.167 10 false VA18 3.031,3.396 3.427,3.563 0.396,0.167 10 false VA22 2.969,3.833 3.365,4 0.396,0.167 10 false VA20 1.396,4.083 1.792,4.25 0.396,0.167 10 false VA11 2.354,4.031 2.75,4.198 0.396,0.167 10 false VA15 2.188,4.302 2.583,4.469 0.396,0.167 10 false VA14 1.865,4.073 2.26,4.24 0.396,0.167 10 false VA13 1.656,4.302 2.052,4.469 0.396,0.167 10 false VA12 1.177,4.292 1.573,4.458 0.396,0.167 10 false VA10 0.99,4.042 1.385,4.208 0.396,0.167 10 false VA9 0.781,4.281 1.177,4.448 0.396,0.167 10 false VA8 0.688,3.625 1.083,3.792 0.396,0.167 10 false VA6 0.396,3.792 0.792,3.958 0.396,0.167 10 false VA3 0.156,3.396 0.552,3.563 0.396,0.167 10 false VA1 1.625,1.313 2.021,1.479 0.396,0.167 10 false z14 0.125,1.385 0.438,1.542 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery Voltage Sensor (for Upper Side))


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the EV battery cells whose value in the freeze frame data was 1.6 V or less only.


Standard Voltage:
Tester Connection EV Battery Cell Condition

Click Location & Routing(z14)Location & Routing

Click Connector(z14)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

z14-10 (GA0) - z14-24 (VA1) 1 Always
z14-24 (VA1) - z14-9 (VA2) 2 Always
z14-9 (VA2) - z14-23 (VA3) 3 Always
z14-23 (VA3) - z14-8 (VA4) 4 Always
z14-8 (VA4) - z14-7 (VA5) 5 Always
z14-7 (VA5) - z14-22 (VA6) 6 Always
z14-22 (VA6) - z14-6 (VA7) 7 Always
z14-6 (VA7) - z14-21 (VA8) 8 Always
z14-21 (VA8) - z14-20 (VA9) 9 Always
z14-20 (VA9) - z14-19 (VA10) 10 Always
z14-19 (VA10) - z14-18 (VA11) 11 Always
z14-18 (VA11) - z14-17 (VA12) 12 Always
z14-17 (VA12) - z14-16 (VA13) 13 Always
z14-16 (VA13) - z14-15 (VA14) 14 Always
z14-15 (VA14) - z14-14 (VA15) 15 Always
z14-14 (VA15) - z14-5 (VA16) 16 Always
z14-5 (VA16) - z14-13 (VA17) 17 Always
z14-13 (VA17) - z14-4 (VA18) 18 Always
z14-4 (VA18) - z14-3 (VA19) 19 Always
z14-3 (VA19) - z14-12 (VA20) 20 Always
z14-12 (VA20) - z14-2 (VA21) 21 Always
z14-2 (VA21) - z14-11 (VA22) 22 Always


CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



iii.

Reconnect the z14 battery voltage sensor (for upper side) connector.



b.

The value of any of the freeze frame data items "Hybrid/EV Battery Cell 23 Voltage" through "Hybrid/EV Battery Cell 42 Voltage" is 1.6 V or less.

i.
C373315N02
0.083,1.229 0.479,1.521 0.396,0.292 0.135,1.292 0.438,1.479 0.302,0.188 10 true z15

Disconnect the z15 battery voltage sensor (for upper side) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



ii.
C371967C09
1.49,1.354 1.917,1.594 0.427,0.24 1.375,2.979 0.875,4.208 true 0.396,2.281 0.896,2.833 true 0.635,1.906 1.021,2.802 true 1.135,2.156 1.188,2.833 true 1.896,1.917 2.167,2.823 true 2.333,2.135 2.323,2.844 true 2.656,1.927 2.469,2.823 true 2.854,2.167 2.604,2.813 true 3.073,2.469 2.74,2.833 true 0.833,3.021 0.375,3.5 true 1.094,3 0.469,3.854 true 1.229,3 0.865,3.677 true 1.51,2.979 1.208,3.969 true 1.646,3 1.448,4.208 true 1.76,3.01 1.708,3.958 true 1.896,3.01 1.979,4.208 true 2.031,2.979 2.208,3.958 true 2.167,2.99 2.531,4.146 true 2.281,2.979 2.563,3.656 true 2.552,3 2.969,3.865 true 2.698,2.979 3.073,3.51 true 0.125,1.427 0.438,1.583 0.313,0.156 10 false *a 1.573,1.385 2.031,1.583 0.458,0.198 10 false z15 2.177,1.969 2.635,2.167 0.458,0.198 10 false VA37 0.104,2.094 0.563,2.292 0.458,0.198 10 false VA23 0.448,1.719 0.906,1.917 0.458,0.198 10 false VA24 0.958,1.927 1.417,2.125 0.458,0.198 10 false VA26 1.729,1.76 2.188,1.958 0.458,0.198 10 false VA35 0.125,3.573 0.583,3.771 0.458,0.198 10 false GA1 2.531,1.781 2.99,1.979 0.458,0.198 10 false VA38 2.76,2 3.219,2.198 0.458,0.198 10 false VA40 2.969,2.302 3.427,2.5 0.458,0.198 10 false VA42 2.479,3.698 2.938,3.896 0.458,0.198 10 false VA36 0.219,3.906 0.677,4.104 0.458,0.198 10 false VA25 0.677,3.719 1.135,3.917 0.458,0.198 10 false VA27 0.688,4.26 1.146,4.458 0.458,0.198 10 false VA28 1.042,4 1.5,4.198 0.458,0.198 10 false VA29 1.24,4.26 1.698,4.458 0.458,0.198 10 false VA30 1.542,4.01 2,4.208 0.458,0.198 10 false VA31 1.865,4.26 2.323,4.458 0.458,0.198 10 false VA32 2.083,4.01 2.542,4.208 0.458,0.198 10 false VA33 2.396,4.208 2.854,4.406 0.458,0.198 10 false VA34 2.844,3.938 3.302,4.135 0.458,0.198 10 false VA39 2.979,3.563 3.365,3.76 0.385,0.198 10 false VA41
*a Rear view of wire harness connector
(to Battery Voltage Sensor (for Upper Side))


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the EV battery cells whose value in the freeze frame data was 1.6 V or less only.


Standard Voltage:
Tester Connection EV Battery Cell Condition

Click Location & Routing(z15)Location & Routing

Click Connector(z15)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

z15-23 (GA1) - z15-8 (VA23) 23 Always
z15-8 (VA23) - z15-7 (VA24) 24 Always
z15-7 (VA24) - z15-22 (VA25) 25 Always
z15-22 (VA25) - z15-6 (VA26) 26 Always
z15-6 (VA26) - z15-21 (VA27) 27 Always
z15-21 (VA27) - z15-20 (VA28) 28 Always
z15-20 (VA28) - z15-19 (VA29) 29 Always
z15-19 (VA29) - z15-18 (VA30) 30 Always
z15-18 (VA30) - z15-17 (VA31) 31 Always
z15-17 (VA31) - z15-16 (VA32) 32 Always
z15-16 (VA32) - z15-15 (VA33) 33 Always
z15-15 (VA33) - z15-14 (VA34) 34 Always
z15-14 (VA34) - z15-5 (VA35) 35 Always
z15-5 (VA35) - z15-13 (VA36) 36 Always
z15-13 (VA36) - z15-4 (VA37) 37 Always
z15-4 (VA37) - z15-3 (VA38) 38 Always
z15-3 (VA38) - z15-12 (VA39) 39 Always
z15-12 (VA39) - z15-2 (VA40) 40 Always
z15-2 (VA40) - z15-11 (VA41) 41 Always
z15-11 (VA41) - z15-1 (VA42) 42 Always


CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



iii.

Reconnect the z15 battery voltage sensor (for upper side) connector.



Result:
Result Proceed to
The voltage between the terminals is below 1.2 V. A
The voltage between the terminals is 1.2 to 1.6 V. B
The voltage between the terminals is higher than 1.6 V. C


Post-procedure1

a.

None.



A

28.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)

B

32.CHECK TOTAL DISTANCE DRIVEN

C

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

28.CHECK BATTERY VOLTAGE SENSOR (for Upper Side) (VA1 - VA42)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When disconnecting connector y1 of the battery voltage sensor (for upper side), first disconnect connectors z14 and z15 from the battery voltage sensor (for upper side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the EV battery cells which measured 1.6 V or less in the previous step.


C371968C06
1.594,1.792 1.99,2.021 0.396,0.229 5.021,1.802 5.417,2.031 0.396,0.229 1.74,4.323 1.75,3.75 true 0.688,3.427 0.438,2.719 true 0.844,3.427 0.573,2.385 true 1,3.448 0.885,2.719 true 1.135,3.417 1.083,2.354 true 1.271,3.427 1.313,2.708 true 2.344,3.406 2.198,2.729 true 2.5,3.417 2.365,2.333 true 2.625,3.427 2.635,2.729 true 2.792,3.448 2.917,2.333 true 0.26,4.344 0.76,3.75 true 0.344,4.74 0.865,3.76 true 0.813,4.313 1.156,3.75 true 0.896,4.719 1.323,3.75 true 1.323,4.313 1.458,3.729 true 1.49,4.74 1.594,3.74 true 1.969,4.729 1.896,3.74 true 2.198,4.313 2.031,3.729 true 2.521,4.74 2.188,3.74 true 2.625,4.292 2.333,3.74 true 2.615,4.292 2.323,3.74 true 3.094,4.719 2.458,3.719 true 3.135,4.333 2.708,3.719 true 3.208,4 2.875,3.719 true 3.698,4.729 4.344,3.75 true 4.219,4.333 4.635,3.74 true 4.313,4.708 4.792,3.74 true 4.76,4.333 4.938,3.75 true 4.948,4.719 5.063,3.76 true 5.208,4.333 5.219,3.74 true 5.448,4.698 5.375,3.74 true 5.667,4.354 5.5,3.771 true 5.969,4.698 5.646,3.74 true 6.063,4.333 5.771,3.75 true 6.563,4.708 5.927,3.729 true 6.615,4.292 6.229,3.74 true 6.677,4.021 6.344,3.74 true 4.438,3.417 4.125,2.708 true 4.594,3.406 4.375,2.333 true 4.74,3.417 4.719,2.729 true 5.823,3.406 5.469,2.323 true 6.083,3.396 6.063,2.302 true 6.375,3.417 6.813,2.344 true 5.958,3.406 5.844,2.719 true 6.24,3.406 6.302,2.729 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 0.198,4.792 0.667,4.969 0.469,0.177 10 false VA3 0.208,2.542 0.604,2.719 0.396,0.177 10 false GA0 0.417,2.177 0.885,2.354 0.469,0.177 10 false VA2 0.76,2.552 1.229,2.729 0.469,0.177 10 false VA4 0.979,2.177 1.448,2.354 0.469,0.177 10 false VA5 1.208,2.552 1.677,2.729 0.469,0.177 10 false VA7 1.969,2.552 2.438,2.729 0.469,0.177 10 false VA16 2.208,2.177 2.677,2.354 0.469,0.177 10 false VA18 2.49,2.552 2.958,2.729 0.469,0.177 10 false VA19 2.781,2.177 3.25,2.354 0.469,0.177 10 false VA21 0.073,4.375 0.542,4.552 0.469,0.177 10 false VA1 0.635,4.375 0.958,4.563 0.323,0.188 10 false VA6 0.74,4.792 1.063,4.979 0.323,0.188 10 false VA8 1.167,4.375 1.49,4.563 0.323,0.188 10 false VA9 1.313,4.781 1.781,4.958 0.469,0.177 10 false VA10 1.583,4.375 2.052,4.552 0.469,0.177 10 false VA11 1.823,4.781 2.292,4.958 0.469,0.177 10 false VA12 2.031,4.375 2.5,4.552 0.469,0.177 10 false VA13 2.365,4.792 2.833,4.969 0.469,0.177 10 false VA14 2.542,4.385 3.01,4.563 0.469,0.177 10 false VA15 2.969,4.792 3.438,4.969 0.469,0.177 10 false VA17 3.115,4.052 3.583,4.229 0.469,0.177 10 false VA22 3.042,4.385 3.51,4.563 0.469,0.177 10 false VA20 3.563,4.792 4.031,4.969 0.469,0.177 10 false GA1 6.667,2.177 7.135,2.354 0.469,0.177 10 false VA42 4.021,4.385 4.49,4.563 0.469,0.177 10 false VA25 4.135,4.792 4.604,4.969 0.469,0.177 10 false VA27 4.583,4.385 5.052,4.563 0.469,0.177 10 false VA28 4.771,4.792 5.24,4.969 0.469,0.177 10 false VA29 5.052,4.385 5.521,4.563 0.469,0.177 10 false VA30 5.292,4.792 5.76,4.969 0.469,0.177 10 false VA31 5.51,4.385 5.979,4.563 0.469,0.177 10 false VA32 5.823,4.792 6.292,4.969 0.469,0.177 10 false VA33 5.958,4.385 6.427,4.563 0.469,0.177 10 false VA34 6.438,4.792 6.906,4.969 0.469,0.177 10 false VA36 6.51,4.385 6.979,4.563 0.469,0.177 10 false VA39 6.646,4.104 7.115,4.281 0.469,0.177 10 false VA41 3.917,2.552 4.385,2.729 0.469,0.177 10 false VA23 4.573,2.552 5.042,2.729 0.469,0.177 10 false VA26 5.677,2.552 6.146,2.729 0.469,0.177 10 false VA37 6.156,2.552 6.625,2.729 0.469,0.177 10 false VA40 4.219,2.177 4.688,2.354 0.469,0.177 10 false VA24 5.292,2.177 5.76,2.354 0.469,0.177 10 false VA35 5.927,2.177 6.396,2.354 0.469,0.177 10 false VA38 1.677,1.813 2.052,2 0.375,0.188 10 false z14 5.104,1.833 5.427,2.031 0.323,0.198 10 false z15
*a Component without harness connected
(Battery Voltage Sensor (for Upper Side))
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
EV Battery Cell Condition Specified Condition

Click Location & Routing(z14,z15)Location & Routing

Click Connector(z14)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

Click Connector(z15)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Upper)

z14-10 (GA0) (-) - z14-24 (VA1) (+) 1 Always 50 kΩ or higher
z14-24 (VA1) (-) - z14-9 (VA2) (+) 2 Always 50 kΩ or higher
z14-9 (VA2) (-) - z14-23 (VA3) (+) 3 Always 50 kΩ or higher
z14-23 (VA3) (-) - z14-8 (VA4) (+) 4 Always 50 kΩ or higher
z14-8 (VA4) (-) - z14-7 (VA5) (+) 5 Always 50 kΩ or higher
z14-7 (VA5) (-) - z14-22 (VA6) (+) 6 Always 50 kΩ or higher
z14-22 (VA6) (-) - z14-6 (VA7) (+) 7 Always 50 kΩ or higher
z14-6 (VA7) (-) - z14-21 (VA8) (+) 8 Always 50 kΩ or higher
z14-21 (VA8) (-) - z14-20 (VA9) (+) 9 Always 50 kΩ or higher
z14-20 (VA9) (-) - z14-19 (VA10) (+) 10 Always 50 kΩ or higher
z14-19 (VA10) (-) - z14-18 (VA11) (+) 11 Always 50 kΩ or higher
z14-18 (VA11) (-) - z14-17 (VA12) (+) 12 Always 50 kΩ or higher
z14-17 (VA12) (-) - z14-16 (VA13) (+) 13 Always 50 kΩ or higher
z14-16 (VA13) (-) - z14-15 (VA14) (+) 14 Always 50 kΩ or higher
z14-15 (VA14) (-) - z14-14 (VA15) (+) 15 Always 50 kΩ or higher
z14-14 (VA15) (-) - z14-5 (VA16) (+) 16 Always 50 kΩ or higher
z14-5 (VA16) (-) - z14-13 (VA17) (+) 17 Always 50 kΩ or higher
z14-13 (VA17) (-) - z14-4 (VA18) (+) 18 Always 50 kΩ or higher
z14-4 (VA18) (-) - z14-3 (VA19) (+) 19 Always 50 kΩ or higher
z14-3 (VA19) (-) - z14-12 (VA20) (+) 20 Always 50 kΩ or higher
z14-12 (VA20) (-) - z14-2 (VA21) (+) 21 Always 50 kΩ or higher
z14-2 (VA21) (-) - z14-11 (VA22) (+) 22 Always 50 kΩ or higher
z15-23 (GA1) (-) - z15-8 (VA23) (+) 23 Always 50 kΩ or higher
z15-8 (VA23) (-) - z15-7 (VA24) (+) 24 Always 50 kΩ or higher
z15-7 (VA24) (-) - z15-22 (VA25) (+) 25 Always 50 kΩ or higher
z15-22 (VA25) (-) - z15-6 (VA26) (+) 26 Always 50 kΩ or higher
z15-6 (VA26) (-) - z15-21 (VA27) (+) 27 Always 50 kΩ or higher
z15-21 (VA27) (-) - z15-20 (VA28) (+) 28 Always 50 kΩ or higher
z15-20 (VA28) (-) - z15-19 (VA29) (+) 29 Always 50 kΩ or higher
z15-19 (VA29) (-) - z15-18 (VA30) (+) 30 Always 50 kΩ or higher
z15-18 (VA30) (-) - z15-17 (VA31) (+) 31 Always 50 kΩ or higher
z15-17 (VA31) (-) - z15-16 (VA32) (+) 32 Always 50 kΩ or higher
z15-16 (VA32) (-) - z15-15 (VA33) (+) 33 Always 50 kΩ or higher
z15-15 (VA33) (-) - z15-14 (VA34) (+) 34 Always 50 kΩ or higher
z15-14 (VA34) (-) - z15-5 (VA35) (+) 35 Always 50 kΩ or higher
z15-5 (VA35) (-) - z15-13 (VA36) (+) 36 Always 50 kΩ or higher
z15-13 (VA36) (-) - z15-4 (VA37) (+) 37 Always 50 kΩ or higher
z15-4 (VA37) (-) - z15-3 (VA38) (+) 38 Always 50 kΩ or higher
z15-3 (VA38) (-) - z15-12 (VA39) (+) 39 Always 50 kΩ or higher
z15-12 (VA39) (-) - z15-2 (VA40) (+) 40 Always 50 kΩ or higher
z15-2 (VA40) (-) - z15-11 (VA41) (+) 41 Always 50 kΩ or higher
z15-11 (VA41) (-) - z15-1 (VA42) (+) 42 Always 50 kΩ or higher


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery voltage sensor, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery voltage sensor.




Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B


Post-procedure1

a.

Install the battery voltage sensor (for upper side).

CAUTION:
C371928N07
0.823,0.094 1.219,0.323 0.396,0.229 0.135,1.271 0.531,1.5 0.396,0.229 2.646,0.823 3.042,1.073 0.396,0.25 0.885,0.125 1.167,0.292 0.281,0.167 10 true z14 0.208,1.302 0.5,1.458 0.292,0.156 10 true z15 2.729,0.865 2.948,1.031 0.219,0.167 10 true y1

When connecting connectors z14 and z15 of the battery voltage sensor (for upper side), first connect connector y1 to the battery voltage sensor (for upper side).




A

29.CHECK TOTAL DISTANCE DRIVEN

B

32.CHECK TOTAL DISTANCE DRIVEN
29.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

30.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
30.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

31.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

34.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
32.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

33.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

35.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
33.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

34.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

35.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

36.REPLACE EV BATTERY TERMINAL BLOCK
36.REPLACE EV BATTERY TERMINAL BLOCK

NEXT

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

37.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373312N04
0.802,0.063 1.177,0.323 0.375,0.26 0.104,1.292 0.49,1.552 0.385,0.26 0.844,0.104 1.125,0.302 0.281,0.198 10 true z16 0.156,1.333 0.427,1.521 0.271,0.188 10 true z17

Check the connections of the z16 and z17 battery voltage sensor (for lower side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Either connector z16 or z17 was not connected securely The terminals are damaged or corroded C



Post-procedure1

a.

None.



A

38.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)

B

CONNECT SECURELY

C

42.CHECK TOTAL DISTANCE DRIVEN
38.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY (EV BATTERY CELL VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the EV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each EV battery cell.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.

The value of any of the freeze frame data items "Hybrid/EV Battery Cell 43 Voltage" through "Hybrid/EV Battery Cell 64 Voltage" is 1.6 V or less.

i.
C373314N02
0.802,0.104 1.167,0.344 0.365,0.24 0.854,0.146 1.135,0.323 0.281,0.177 10 true z16

Disconnect the z16 battery voltage sensor (for lower side) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



ii.
C371966C08
1.531,1.271 1.938,1.5 0.406,0.229 0.656,2.688 0.375,2.396 true 2.208,2.677 1.99,1.865 true 0.781,2.667 0.479,2.094 true 0.885,2.688 0.677,1.854 true 1.031,2.688 1.021,2.073 true 1.188,2.656 1.323,1.844 true 2.281,4.271 2.031,2.865 true 2.354,2.667 2.344,2.073 true 2.615,2.667 2.948,2.083 true 2.479,2.667 2.75,1.833 true 3.021,3.333 2.698,2.865 true 2.948,3.771 2.542,2.865 true 2.583,3.573 2.313,2.854 true 2.469,3.979 2.167,2.865 true 2,4 1.896,2.854 true 1.75,4.271 1.729,2.854 true 1.573,4.031 1.635,2.844 true 0.833,3.594 1.104,2.844 true 1.146,4 1.344,2.844 true 0.896,4.24 1.229,2.844 true 1.323,4.26 1.521,2.854 true 0.531,3.76 0.844,2.854 true 0.354,3.365 0.698,2.865 true 2.5,3.646 2.896,3.813 0.396,0.167 10 false VA59 0.094,2.229 0.49,2.396 0.396,0.167 10 false GA2 0.354,1.896 0.75,2.063 0.396,0.167 10 false VA44 0.51,1.646 0.906,1.813 0.396,0.167 10 false VA46 0.885,1.885 1.281,2.052 0.396,0.167 10 false VA47 1.208,1.635 1.604,1.802 0.396,0.167 10 false VA49 1.792,1.667 2.188,1.833 0.396,0.167 10 false VA58 2.885,1.896 3.281,2.063 0.396,0.167 10 false VA63 2.615,1.615 3.01,1.781 0.396,0.167 10 false VA61 2.208,1.885 2.604,2.052 0.396,0.167 10 false VA60 3.031,3.396 3.427,3.563 0.396,0.167 10 false VA64 2.969,3.833 3.365,4 0.396,0.167 10 false VA62 1.396,4.083 1.792,4.25 0.396,0.167 10 false VA53 2.354,4.031 2.75,4.198 0.396,0.167 10 false VA57 2.188,4.302 2.583,4.469 0.396,0.167 10 false VA56 1.865,4.073 2.26,4.24 0.396,0.167 10 false VA55 1.656,4.302 2.052,4.469 0.396,0.167 10 false VA54 1.177,4.292 1.573,4.458 0.396,0.167 10 false VA52 0.99,4.042 1.385,4.208 0.396,0.167 10 false VA51 0.781,4.281 1.177,4.448 0.396,0.167 10 false VA50 0.688,3.625 1.083,3.792 0.396,0.167 10 false VA48 0.396,3.792 0.792,3.958 0.396,0.167 10 false VA45 0.156,3.396 0.552,3.563 0.396,0.167 10 false VA43 1.615,1.302 1.906,1.479 0.292,0.177 10 false z16 0.125,1.385 0.438,1.542 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Battery Voltage Sensor (for Lower Side))


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the EV battery cells whose value in the freeze frame data was 1.6 V or less only.


Standard Voltage:
Tester Connection EV Battery Cell Condition

Click Location & Routing(z16)Location & Routing

Click Connector(z16)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

z16-10 (GA2) - z16-24 (VA43) 43 Always
z16-24 (VA43) - z16-9 (VA44) 44 Always
z16-9 (VA44) - z16-23 (VA45) 45 Always
z16-23 (VA45) - z16-8 (VA46) 46 Always
z16-8 (VA46) - z16-7 (VA47) 47 Always
z16-7 (VA47) - z16-22 (VA48) 48 Always
z16-22 (VA48) - z16-6 (VA49) 49 Always
z16-6 (VA49) - z16-21 (VA50) 50 Always
z16-21 (VA50) - z16-20 (VA51) 51 Always
z16-20 (VA51) - z16-19 (VA52) 52 Always
z16-19 (VA52) - z16-18 (VA53) 53 Always
z16-18 (VA53) - z16-17 (VA54) 54 Always
z16-17 (VA54) - z16-16 (VA55) 55 Always
z16-16 (VA55) - z16-15 (VA56) 56 Always
z16-15 (VA56) - z16-14 (VA57) 57 Always
z16-14 (VA57) - z16-5 (VA58) 58 Always
z16-5 (VA58) - z16-13 (VA59) 59 Always
z16-13 (VA59) - z16-4 (VA60) 60 Always
z16-4 (VA60) - z16-3 (VA61) 61 Always
z16-3 (VA61) - z16-12 (VA62) 62 Always
z16-12 (VA62) - z16-2 (VA63) 63 Always
z16-2 (VA63) - z16-11 (VA64) 64 Always


CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



iii.

Reconnect the z16 battery voltage sensor (for lower side) connector.



b.

The value of any of the freeze frame data items "Hybrid/EV Battery Cell 65 Voltage" through "Hybrid/EV Battery Cell 84 Voltage" is 1.6 V or less.

i.
C373316N02
0.063,1.25 0.521,1.542 0.458,0.292 0.167,1.292 0.469,1.5 0.302,0.208 10 true z17

Disconnect the z17 battery voltage sensor (for lower side) connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



ii.
C371967C10
1.469,1.375 1.865,1.604 0.396,0.229 1.375,2.979 0.875,4.208 true 0.396,2.281 0.896,2.833 true 0.635,1.906 1.021,2.802 true 1.135,2.156 1.188,2.833 true 1.896,1.917 2.167,2.823 true 2.333,2.135 2.323,2.844 true 2.656,1.927 2.469,2.823 true 2.854,2.167 2.604,2.813 true 3.073,2.469 2.74,2.833 true 0.833,3.021 0.375,3.5 true 1.094,3 0.469,3.854 true 1.229,3 0.865,3.677 true 1.51,2.979 1.208,3.969 true 1.646,3 1.448,4.208 true 1.76,3.01 1.708,3.958 true 1.896,3.01 1.979,4.208 true 2.031,2.979 2.208,3.958 true 2.167,2.99 2.531,4.146 true 2.281,2.979 2.563,3.656 true 2.552,3 2.969,3.865 true 2.698,2.979 3.073,3.51 true 0.125,1.427 0.438,1.583 0.313,0.156 10 false *a 1.552,1.396 1.854,1.594 0.302,0.198 10 false z17 2.177,1.958 2.635,2.156 0.458,0.198 10 false VA79 0.104,2.094 0.563,2.292 0.458,0.198 10 false VA65 0.448,1.719 0.906,1.917 0.458,0.198 10 false VA66 0.958,1.927 1.417,2.125 0.458,0.198 10 false VA68 1.729,1.76 2.188,1.958 0.458,0.198 10 false VA77 0.125,3.573 0.583,3.771 0.458,0.198 10 false GA3 2.531,1.781 2.99,1.979 0.458,0.198 10 false VA80 2.76,2 3.219,2.198 0.458,0.198 10 false VA82 2.969,2.302 3.427,2.5 0.458,0.198 10 false VA84 2.479,3.698 2.938,3.896 0.458,0.198 10 false VA78 0.219,3.906 0.677,4.104 0.458,0.198 10 false VA67 0.677,3.719 1.135,3.917 0.458,0.198 10 false VA69 0.688,4.26 1.146,4.458 0.458,0.198 10 false VA70 1.042,4 1.5,4.198 0.458,0.198 10 false VA71 1.24,4.26 1.698,4.458 0.458,0.198 10 false VA72 1.542,4.01 2,4.208 0.458,0.198 10 false VA73 1.865,4.26 2.323,4.458 0.458,0.198 10 false VA74 2.083,4 2.542,4.198 0.458,0.198 10 false VA75 2.396,4.208 2.854,4.406 0.458,0.198 10 false VA76 2.844,3.938 3.302,4.135 0.458,0.198 10 false VA81 2.979,3.563 3.365,3.76 0.385,0.198 10 false VA83
*a Rear view of wire harness connector
(to Battery Voltage Sensor (for Lower Side))


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the EV battery cells whose value in the freeze frame data was 1.6 V or less only.


Standard Voltage:
Tester Connection EV Battery Cell Condition

Click Location & Routing(z17)Location & Routing

Click Connector(z17)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

z17-23 (GA3) - z17-8 (VA65) 65 Always
z17-8 (VA65) - z17-7 (VA66) 66 Always
z17-7 (VA66) - z17-22 (VA67) 67 Always
z17-22 (VA67) - z17-6 (VA68) 68 Always
z17-6 (VA68) - z17-21 (VA69) 69 Always
z17-21 (VA69) - z17-20 (VA70) 70 Always
z17-20 (VA70) - z17-19 (VA71) 71 Always
z17-19 (VA71) - z17-18 (VA72) 72 Always
z17-18 (VA72) - z17-17 (VA73) 73 Always
z17-17 (VA73) - z17-16 (VA74) 74 Always
z17-16 (VA74) - z17-15 (VA75) 75 Always
z17-15 (VA75) - z17-14 (VA76) 76 Always
z17-14 (VA76) - z17-5 (VA77) 77 Always
z17-5 (VA77) - z17-13 (VA78) 78 Always
z17-13 (VA78) - z17-4 (VA79) 79 Always
z17-4 (VA79) - z17-3 (VA80) 80 Always
z17-3 (VA80) - z17-12 (VA81) 81 Always
z17-12 (VA81) - z17-2 (VA82) 82 Always
z17-2 (VA82) - z17-11 (VA83) 83 Always
z17-11 (VA83) - z17-1 (VA84) 84 Always


CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



iii.

Reconnect the z17 battery voltage sensor (for lower side) connector.



Result:
Result Proceed to
The voltage between the terminals is below 1.2 V. A
The voltage between the terminals is 1.2 to 1.6 V. B
The voltage between the terminals is higher than 1.6 V. C


Post-procedure1

a.

None.



A

39.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)

B

43.CHECK TOTAL DISTANCE DRIVEN

C

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

39.CHECK BATTERY VOLTAGE SENSOR (for Lower Side) (VA43 - VA84)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the battery voltage sensor (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When disconnecting connector y3 of the battery voltage sensor (for lower side), first disconnect connectors z16 and z17 from the battery voltage sensor (for lower side).


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the EV battery cells which measured 1.6 V or less in the previous step.


C371968C07
1.594,1.792 1.99,2.021 0.396,0.229 5.021,1.802 5.417,2.031 0.396,0.229 1.74,4.323 1.75,3.75 true 0.688,3.427 0.438,2.719 true 0.844,3.427 0.573,2.385 true 1,3.448 0.885,2.719 true 1.135,3.417 1.083,2.354 true 1.271,3.427 1.313,2.708 true 2.344,3.406 2.198,2.729 true 2.5,3.417 2.365,2.354 true 2.625,3.427 2.635,2.729 true 2.792,3.448 2.917,2.365 true 0.26,4.344 0.76,3.75 true 0.344,4.74 0.865,3.76 true 0.813,4.313 1.156,3.75 true 0.896,4.719 1.323,3.75 true 1.323,4.313 1.458,3.729 true 1.49,4.74 1.594,3.74 true 1.969,4.729 1.896,3.74 true 2.198,4.313 2.031,3.729 true 2.521,4.74 2.188,3.74 true 2.625,4.292 2.333,3.74 true 2.615,4.292 2.323,3.74 true 3.094,4.719 2.458,3.719 true 3.135,4.333 2.708,3.719 true 3.208,4 2.875,3.719 true 3.698,4.729 4.344,3.75 true 4.219,4.333 4.635,3.74 true 4.313,4.708 4.792,3.74 true 4.76,4.333 4.938,3.75 true 4.948,4.719 5.063,3.76 true 5.208,4.333 5.219,3.74 true 5.448,4.698 5.375,3.74 true 5.667,4.354 5.5,3.771 true 5.969,4.698 5.646,3.74 true 6.063,4.333 5.771,3.75 true 6.563,4.708 5.927,3.729 true 6.615,4.292 6.229,3.74 true 6.677,4.021 6.344,3.74 true 4.438,3.417 4.125,2.708 true 4.594,3.406 4.375,2.354 true 4.74,3.417 4.719,2.729 true 5.823,3.406 5.479,2.344 true 6.083,3.396 6.063,2.344 true 6.375,3.417 6.813,2.365 true 5.958,3.406 5.844,2.719 true 6.24,3.406 6.302,2.729 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 0.198,4.802 0.667,4.979 0.469,0.177 10 false VA45 0.208,2.542 0.604,2.719 0.396,0.177 10 false GA2 0.417,2.177 0.885,2.354 0.469,0.177 10 false VA44 0.719,2.552 1.188,2.729 0.469,0.177 10 false VA46 0.948,2.177 1.417,2.354 0.469,0.177 10 false VA47 1.167,2.552 1.635,2.729 0.469,0.177 10 false VA49 1.969,2.552 2.438,2.729 0.469,0.177 10 false VA58 2.208,2.177 2.677,2.354 0.469,0.177 10 false VA60 2.49,2.552 2.958,2.729 0.469,0.177 10 false VA61 2.781,2.177 3.25,2.354 0.469,0.177 10 false VA63 0.073,4.375 0.542,4.552 0.469,0.177 10 false VA43 0.594,4.375 1.021,4.573 0.427,0.198 10 false VA48 0.698,4.792 1.125,5.01 0.427,0.219 10 false VA50 1.125,4.375 1.521,4.563 0.396,0.188 10 false VA51 1.313,4.781 1.781,4.958 0.469,0.177 10 false VA52 1.583,4.375 2.052,4.552 0.469,0.177 10 false VA53 1.823,4.781 2.292,4.958 0.469,0.177 10 false VA54 2.031,4.375 2.5,4.552 0.469,0.177 10 false VA55 2.365,4.792 2.833,4.969 0.469,0.177 10 false VA56 2.542,4.385 3.01,4.563 0.469,0.177 10 false VA57 2.969,4.792 3.438,4.969 0.469,0.177 10 false VA59 3.115,4.052 3.583,4.229 0.469,0.177 10 false VA64 3.042,4.385 3.51,4.563 0.469,0.177 10 false VA62 3.563,4.792 4.031,4.969 0.469,0.177 10 false GA3 6.667,2.177 7.135,2.354 0.469,0.177 10 false VA84 4.021,4.385 4.49,4.563 0.469,0.177 10 false VA67 4.135,4.792 4.604,4.969 0.469,0.177 10 false VA69 4.583,4.385 5.052,4.563 0.469,0.177 10 false VA70 4.771,4.792 5.24,4.969 0.469,0.177 10 false VA71 5.052,4.385 5.521,4.563 0.469,0.177 10 false VA72 5.292,4.792 5.76,4.969 0.469,0.177 10 false VA73 5.51,4.385 5.979,4.563 0.469,0.177 10 false VA74 5.823,4.792 6.292,4.969 0.469,0.177 10 false VA75 5.958,4.385 6.427,4.563 0.469,0.177 10 false VA76 6.438,4.792 6.906,4.969 0.469,0.177 10 false VA78 6.51,4.385 6.979,4.563 0.469,0.177 10 false VA81 6.646,4.104 7.115,4.281 0.469,0.177 10 false VA83 3.917,2.552 4.385,2.729 0.469,0.177 10 false VA65 4.573,2.552 5.042,2.729 0.469,0.177 10 false VA68 5.677,2.552 6.146,2.729 0.469,0.177 10 false VA79 6.156,2.552 6.625,2.729 0.469,0.177 10 false VA82 4.219,2.177 4.688,2.354 0.469,0.177 10 false VA66 5.292,2.177 5.76,2.354 0.469,0.177 10 false VA77 5.927,2.177 6.396,2.354 0.469,0.177 10 false VA80 1.677,1.823 2.052,2.01 0.375,0.188 10 false z16 5.115,1.844 5.438,2.042 0.323,0.198 10 false z17
*a Component without harness connected
(Battery Voltage Sensor (for Lower Side))
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
EV Battery Cell Condition Specified Condition

Click Location & Routing(z16,z17)Location & Routing

Click Connector(z16)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

Click Connector(z17)Body>other>EV Supply Battery Assembly , Battery Voltage Sensor (Lower)

z16-10 (GA2) (-) - z16-24 (VA43) (+) 43 Always 50 kΩ or higher
z16-24 (VA43) (-) - z16-9 (VA44) (+) 44 Always 50 kΩ or higher
z16-9 (VA44) (-) - z16-23 (VA45) (+) 45 Always 50 kΩ or higher
z16-23 (VA45) (-) - z16-8 (VA46) (+) 46 Always 50 kΩ or higher
z16-8 (VA46) (-) - z16-7 (VA47) (+) 47 Always 50 kΩ or higher
z16-7 (VA47) (-) - z16-22 (VA48) (+) 48 Always 50 kΩ or higher
z16-22 (VA48) (-) - z16-6 (VA49) (+) 49 Always 50 kΩ or higher
z16-6 (VA49) (-) - z16-21 (VA50) (+) 50 Always 50 kΩ or higher
z16-21 (VA50) (-) - z16-20 (VA51) (+) 51 Always 50 kΩ or higher
z16-20 (VA51) (-) - z16-19 (VA52) (+) 52 Always 50 kΩ or higher
z16-19 (VA52) (-) - z16-18 (VA53) (+) 53 Always 50 kΩ or higher
z16-18 (VA53) (-) - z16-17 (VA54) (+) 54 Always 50 kΩ or higher
z16-17 (VA54) (-) - z16-16 (VA55) (+) 55 Always 50 kΩ or higher
z16-16 (VA55) (-) - z16-15 (VA56) (+) 56 Always 50 kΩ or higher
z16-15 (VA56) (-) - z16-14 (VA57) (+) 57 Always 50 kΩ or higher
z16-14 (VA57) (-) - z16-5 (VA58) (+) 58 Always 50 kΩ or higher
z16-5 (VA58) (-) - z16-13 (VA59) (+) 59 Always 50 kΩ or higher
z16-13 (VA59) (-) - z16-4 (VA60) (+) 60 Always 50 kΩ or higher
z16-4 (VA60) (-) - z16-3 (VA61) (+) 61 Always 50 kΩ or higher
z16-3 (VA61) (-) - z16-12 (VA62) (+) 62 Always 50 kΩ or higher
z16-12 (VA62) (-) - z16-2 (VA63) (+) 63 Always 50 kΩ or higher
z16-2 (VA63) (-) - z16-11 (VA64) (+) 64 Always 50 kΩ or higher
z17-23 (GA3) (-) - z17-8 (VA65) (+) 65 Always 50 kΩ or higher
z17-8 (VA65) (-) - z17-7 (VA66) (+) 66 Always 50 kΩ or higher
z17-7 (VA66) (-) - z17-22 (VA67) (+) 67 Always 50 kΩ or higher
z17-22 (VA67) (-) - z17-6 (VA68) (+) 68 Always 50 kΩ or higher
z17-6 (VA68) (-) - z17-21 (VA69) (+) 69 Always 50 kΩ or higher
z17-21 (VA69) (-) - z17-20 (VA70) (+) 70 Always 50 kΩ or higher
z17-20 (VA70) (-) - z17-19 (VA71) (+) 71 Always 50 kΩ or higher
z17-19 (VA71) (-) - z17-18 (VA72) (+) 72 Always 50 kΩ or higher
z17-18 (VA72) (-) - z17-17 (VA73) (+) 73 Always 50 kΩ or higher
z17-17 (VA73) (-) - z17-16 (VA74) (+) 74 Always 50 kΩ or higher
z17-16 (VA74) (-) - z17-15 (VA75) (+) 75 Always 50 kΩ or higher
z17-15 (VA75) (-) - z17-14 (VA76) (+) 76 Always 50 kΩ or higher
z17-14 (VA76) (-) - z17-5 (VA77) (+) 77 Always 50 kΩ or higher
z17-5 (VA77) (-) - z17-13 (VA78) (+) 78 Always 50 kΩ or higher
z17-13 (VA78) (-) - z17-4 (VA79) (+) 79 Always 50 kΩ or higher
z17-4 (VA79) (-) - z17-3 (VA80) (+) 80 Always 50 kΩ or higher
z17-3 (VA80) (-) - z17-12 (VA81) (+) 81 Always 50 kΩ or higher
z17-12 (VA81) (-) - z17-2 (VA82) (+) 82 Always 50 kΩ or higher
z17-2 (VA82) (-) - z17-11 (VA83) (+) 83 Always 50 kΩ or higher
z17-11 (VA83) (-) - z17-1 (VA84) (+) 84 Always 50 kΩ or higher


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery voltage sensor, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery voltage sensor.




Result:
Result Proceed to
The resistance between the terminals is 50 kΩ or higher. A
Other than above B


Post-procedure1

a.

Install the battery voltage sensor (for lower side).

CAUTION:
C371929N05
2.635,0.802 3.052,1.083 0.417,0.281 0.146,1.281 0.521,1.531 0.375,0.25 0.719,0.135 1.125,0.385 0.406,0.25 0.792,0.188 1.083,0.354 0.292,0.167 10 true z16 0.188,1.323 0.479,1.49 0.292,0.167 10 true z17 2.76,0.875 3,1.042 0.24,0.167 10 true y3

When connecting connectors z16 and z17 of the battery voltage sensor (for lower side), first connect connector y3 to the battery voltage sensor (for lower side).




A

40.CHECK TOTAL DISTANCE DRIVEN

B

43.CHECK TOTAL DISTANCE DRIVEN
40.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

41.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
41.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

42.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

45.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
43.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

44.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

46.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
44.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

45.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

46.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

47.REPLACE EV BATTERY TERMINAL BLOCK
47.REPLACE EV BATTERY TERMINAL BLOCK

NEXT

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

48.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Upper Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for upper side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373311N03
0.865,0.042 1.26,0.333 0.396,0.292 0.104,1.281 0.49,1.542 0.385,0.26 0.938,0.115 1.229,0.281 0.292,0.167 10 true z14 0.177,1.323 0.438,1.5 0.26,0.177 10 true z15

Check the connections of the z14 and z15 battery voltage sensor (for upper side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
The connector z14 or z15 terminals are abnormal The terminals are damaged or corroded C
The battery voltage sensor (for upper side) terminals are abnormal The terminals are damaged or corroded D


Post-procedure1

a.

None.



A

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

B

CONNECT SECURELY

C

49.CHECK TOTAL DISTANCE DRIVEN

D

REPLACE BATTERY VOLTAGE SENSOR (for Upper Side)

49.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

B

50.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
50.REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK

51.CHECK CONNECTOR CONNECTION CONDITION (BATTERY VOLTAGE SENSOR (for Lower Side) CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery protector (for lower side).

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL



Procedure1

a.
C373312N04
0.802,0.063 1.177,0.323 0.375,0.26 0.104,1.292 0.49,1.552 0.385,0.26 0.844,0.104 1.125,0.302 0.281,0.198 10 true z16 0.156,1.333 0.427,1.521 0.271,0.188 10 true z17

Check the connections of the z16 and z17 battery voltage sensor (for lower side) connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
The connector z16 or z17 terminals are abnormal The terminals are damaged or corroded C
The battery voltage sensor (for lower side) terminals are abnormal The terminals are damaged or corroded D


Post-procedure1

a.

None.



A

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

B

CONNECT SECURELY

C

52.CHECK TOTAL DISTANCE DRIVEN

D

REPLACE BATTERY VOLTAGE SENSOR (for Lower Side)

52.CHECK TOTAL DISTANCE DRIVEN
a.

Check the recorded total distance traveled of the vehicle.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when EV battery terminal block replaced = less than 200000 km (124280 mile)*1
Other than above B


HINT:

*1: If the EV battery terminal block has been replaced, use the total distance driven since it was replaced.



A

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

B

53.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
53.REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NEXT

REPLACE EV BATTERY TERMINAL BLOCK