Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0A13  High Voltage System Interlock Circuit Open  P0A0A92  High Voltage System Interlock Performance or Incorrect Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)

The cause of this malfunction may be one of the following:

Detection switch system malfunction
·

Service plug malfunction

·

Inverter with converter malfanction


Low-voltage system malfunction
·

EV control ECU malfunction

·

Service plug malfunction

·

Wire harness malfunction

·

Connector malfunction

·

Inverter with converter malfanction



INSPECTION DESCRIPTION


A337293E04
3.635,4.094 5.844,4.302 2.208,0.208 10 false Service Plug Grip (Interlock Switch) 1.26,4.146 1.563,4.365 0.302,0.219 10 false : *b 2.979,1.552 4.521,1.792 1.542,0.24 10 false Inverter Terminal Cover 1.885,2.74 3.865,3.01 1.979,0.271 10 false Connector Cover Assembly 0.729,1.542 1.958,1.885 1.229,0.344 10 false Front Compartment Main Wire 1.792,0.927 1.979,1.146 0.188,0.219 10 false *a 3.99,0.906 4.177,1.125 0.188,0.219 10 false *a 3,2.104 3.188,2.323 0.188,0.219 10 false *a 4.563,3.313 4.75,3.531 0.188,0.219 10 false *a 5.385,1.646 5.573,1.865 0.188,0.219 10 false *a 5.552,0.906 5.74,1.125 0.188,0.219 10 false *a 5.906,2.688 7.156,2.896 1.25,0.208 10 false EV Control ECU 0.396,3.323 2.521,3.594 2.125,0.271 10 false Inverter with Converter Assembly

System Diagram Location Inspection Content Reason
*a
·

Check whether the safety device (interlock) is connected securely and installed properly (service plug grip, inverter terminal cover or connector cover assembly, etc.).

·

EV control ECU or inverter connector


DTC output due to improper connection or forgetting to install parts.
*b Inspect the detection circuit. DTC output due to an open circuit or improper connection (dirt, foreign matter, etc.).


DESCRIPTION

When the EV control ECU detects that a safety device (interlock) is operated, such as when the service plug grip, connector cover assembly or inverter terminal cover is removed, it will prohibit EV control system operation or shut off the system main relay. The 4 safety devices are located as follows; 1 in the service plug grip, 1 in the EV fuse maintenance connector cover asembly of the inverter with converter assembly, 1 on the inverter terminal cover for the terminals of the No. 2 battery pack wire and FC air compressor motor cable assembly and 1 in the front compartment main wire to the inverter with converter assembly. If the service plug grip, connector cover assembly, inverter terminal cover or front compartment main wire is removed, the interlock signal line will be open. If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. When the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned to ON.

The system main relay will be turned off from the next trip after the open is detected until the condition returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0A0A13 High Voltage System Interlock Circuit Open Interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more)
(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

Service plug grip

·

Inverter with converter assembly

·

Front compartment main wire

·

Inverter terminal cover


Master Warning:
Comes on
EV A
P0A0A92 High Voltage System Interlock Performance or Incorrect Operation Either of the following conditions is met:
·

With the vehicle stopped, the service plug grip with a safety device was removed.

·

With the vehicle stopped, the interlock signal line became open.


(1 trip detection logic)
·

Wire harness or connector

·

EV control ECU

·

Service plug grip

·

Inverter with converter assembly

·

Front compartment main wire

·

Inverter terminal cover


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (IG) and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A341091E04
0.729,1.49 2.792,1.688 2.063,0.198 10 false Front Compartment Main Wire 2.938,1.5 4.927,1.698 1.99,0.198 10 false Inverter Terminal Cover 1.917,2.417 4.083,2.677 2.167,0.26 10 false Connector Cover Assembly 5.958,2.854 7.021,3.104 1.063,0.25 10 false EV Control ECU 0.198,3.49 2.354,3.719 2.156,0.229 10 false Inverter with Converter Assembly 3.854,4.167 6.219,4.417 2.365,0.25 10 false Service Plug Grip (Interlock Switch) 0.219,3.323 0.573,3.51 0.354,0.188 10 false A19 3.865,4 4.219,4.188 0.354,0.188 10 false z25 3.729,3.583 4.083,3.771 0.354,0.188 10 false 2 4.875,3.594 5.229,3.781 0.354,0.188 10 false 1 3.885,3.604 4.24,3.792 0.354,0.188 10 false GND 4.573,3.594 4.927,3.781 0.354,0.188 10 false ILK 5.948,2.698 6.302,2.885 0.354,0.188 10 false A17 5.042,1.188 5.396,1.375 0.354,0.188 10 false 35 5.052,2.125 5.406,2.313 0.354,0.188 10 false 24 5.688,1.188 6.042,1.375 0.354,0.188 10 false 28 5.938,1.198 6.292,1.385 0.354,0.188 10 false ILK 6.427,0.406 6.781,0.594 0.354,0.188 10 false +B 4.708,1.188 5.063,1.375 0.354,0.188 10 false ILKI 4.646,2.125 5,2.313 0.354,0.188 10 false ILKO

for RHD:
A341091E05
0.75,1.49 2.813,1.688 2.063,0.198 10 false Front Compartment Main Wire 2.938,1.5 4.927,1.698 1.99,0.198 10 false Inverter Terminal Cover 1.917,2.417 4.083,2.677 2.167,0.26 10 false Connector Cover Assembly 5.958,2.854 7.021,3.104 1.063,0.25 10 false EV Control ECU 0.198,3.49 2.354,3.719 2.156,0.229 10 false Inverter with Converter Assembly 3.854,4.167 6.219,4.417 2.365,0.25 10 false Service Plug Grip (Interlock Switch) 0.219,3.323 0.573,3.51 0.354,0.188 10 false A18 3.865,4 4.219,4.188 0.354,0.188 10 false z25 3.719,3.604 4.073,3.792 0.354,0.188 10 false 2 4.865,3.615 5.219,3.802 0.354,0.188 10 false 1 3.885,3.594 4.24,3.781 0.354,0.188 10 false GND 4.583,3.594 4.938,3.781 0.354,0.188 10 false ILK 5.948,2.698 6.302,2.885 0.354,0.188 10 false A17 5.031,1.208 5.385,1.396 0.354,0.188 10 false 35 5.042,2.146 5.396,2.333 0.354,0.188 10 false 24 5.708,1.229 6.063,1.417 0.354,0.188 10 false 28 5.938,1.229 6.292,1.417 0.354,0.188 10 false ILK 6.427,0.406 6.781,0.594 0.354,0.188 10 false +B 4.698,1.208 5.052,1.396 0.354,0.188 10 false ILKI 4.656,2.135 5.01,2.323 0.354,0.188 10 false ILKO

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0A0A13 or P0A0A92 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
Power source circuit malfunction P06881F ECM/PCM Power Relay Sense Circuit Intermittent
System malfunction P1C9E9F Hybrid/EV System Reset Stuck Off

HINT:
·

P0A0A13 or P0A0A92 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (EV)
3.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 5 seconds or more.


Procedure1

a.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
Result:
Proceed to Proceed to
P0A0A13 or P0A0A92 is output A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK SERVICE PLUG GRIP

B

16.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
4.CHECK SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


a.
A365595C01
0.104,0.094 0.417,0.25 0.313,0.156 10 false *1
*1 Service Plug Grip


Check if the service plug grip is installed correctly.

NOTICE:

Insert the service plug grip until a click sound is heard.


HINT:
·

For the removal and installation procedures.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL

·

P0A0A92 is also set if the ignition switch is turned to ON with the service plug grip removed. Confirm the conditions when the malfunction occurred.




Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)

NG

INSTALL PARTS CORRECTLY

5.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Remove the No. 8 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL



b.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A478497C01
1.792,1.896 2.01,2.104 0.219,0.208 10 true *1
*1 Interlock Connector


Check that the interlock connector at the service plug grip installation socket is connected correctly.

OK:

The connector is connected correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 8 EV battery shield panel.



OK

6.CHECK CONNECTOR COVER ASSEMBLY

NG

INSTALL PARTS CORRECTLY

6.CHECK CONNECTOR COVER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A484690C01
0.021,0.021 0.333,0.219 0.313,0.198 10 true *A 0.021,2.5 0.333,2.698 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check if the connector cover assembly of the inverter with converter assembly is installed correctly.

OK:

The connector cover assembly is installed correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

7.CHECK INVERTER TERMINAL COVER

NG

CONNECT SECURELY

7.CHECK INVERTER TERMINAL COVER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A483161C01
0.042,0.042 0.354,0.24 0.313,0.198 10 true *A 0.042,2.479 0.354,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check if the inverter terminal cover of the inverter with converter assembly is installed correctly.

OK:

The inverter terminal cover is installed correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

8.CHECK FRONT COMPARTMENT MAIN WIRE

NG

CONNECT SECURELY

8.CHECK FRONT COMPARTMENT MAIN WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A483163C01
0.031,0 0.344,0.198 0.313,0.198 10 true *A 0.031,2.479 0.344,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check if the front compartment main wire is connected correctly.

OK:

The front compartment main wire is connected correctly.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A001C

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

10.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

11.CHECK EV CONTROL ECU

NG

CONNECT SECURELY

11.CHECK EV CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL


*1: for LHD

*2: for RHD


Procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.
C361311C85
0.031,1.146 0.438,1.479 0.406,0.333 0.031,0.667 0.438,1 0.406,0.333 1.146,1.833 1.427,1.333 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 0.99,1.875 1.604,2.073 0.615,0.198 10 false ILKI 0.115,1.219 0.573,1.417 0.458,0.198 10 false A18 0.115,0.729 0.573,0.927 0.458,0.198 10 false A19 0.49,0.74 0.802,0.938 0.313,0.198 10 false *A 0.5,1.229 0.813,1.427 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard voltage:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-35 (ILKI) - Body ground Ignition switch ON 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-35 (ILKI) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

12.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERLOCK)

NG

17.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
12.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERLOCK)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD


Procedure1

a.
C256313C60
1.844,0.094 2.24,0.375 0.396,0.281 1,0.094 1.396,0.375 0.396,0.281 1.552,1.792 1.99,1.219 true 2.385,1.781 2,1.115 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.927,0.156 2.292,0.323 0.365,0.167 10 false A18 2.281,1.813 2.646,1.979 0.365,0.167 10 false ILKO 1.448,1.823 1.813,1.99 0.365,0.167 10 false ILKI 1.094,0.156 1.458,0.323 0.365,0.167 10 false A19 1.448,0.156 1.76,0.354 0.313,0.198 10 false *A 2.26,0.146 2.573,0.344 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A19-35 (ILKI) - A19-24 (ILKO) Ignition switch off Below 10 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

A18-35 (ILKI) - A18-24 (ILKO) Ignition switch off Below 10 Ω


NOTICE:

Do not remove the inverter terminal cover, connector cover assembly and front compartment main wire.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

13.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - SERVICE PLUG GRIP)

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - SERVICE PLUG GRIP)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Remove the No. 8 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL



b.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



c.

Disconnect the z25 service plug grip (interlock switch) connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A478498C03
1.604,1.823 2.042,2.104 0.438,0.281 2.781,0.854 2.927,0.635 true 2.479,0.146 2.677,0.313 0.198,0.167 10 false *a 1.719,1.906 1.969,2.104 0.25,0.198 10 false z25 2.615,0.875 2.896,1.052 0.281,0.177 10 false ILK
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z25)Location & Routing

Click Connector(z25)Body>other>EV Supply Battery Assembly , Inter Lock Switch

z25-1 (ILK) - Body ground Ignition switch off 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the service plug grip (interlock switch) connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z25 service plug grip (interlock switch) connector.


d.

Install the No. 8 EV battery shield panel.



OK

14.CHECK SERVICE PLUG GRIP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Procedure1

a.
A365596C05
0.115,0.083 0.427,0.24 0.313,0.156 10 false *1
*1 Service Plug Grip


Check the condition of the service plug grip interlock.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

15.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)

NG

15.CHECK HARNESS AND CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Remove the No. 8 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL



b.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



c.

Disconnect the z25 service plug grip (interlock switch) connector.


Procedure1

a.
A478498C02
1.625,1.802 2.042,2.104 0.417,0.302 2.615,0.844 2.75,0.635 true 2.49,0.135 2.74,0.344 0.25,0.208 10 false *a 1.729,1.885 1.99,2.083 0.26,0.198 10 false z25 2.448,0.865 2.896,1.052 0.448,0.188 10 false GND
*a Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z25)Location & Routing

Click Connector(z25)Body>other>EV Supply Battery Assembly , Inter Lock Switch

z25-2 (GND) - Body ground Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z25 service plug grip (interlock switch) connector.


b.

Install the No. 8 EV battery shield panel.



OK

16.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
a.

Check the connections of each connector.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CONNECTOR

17.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - EV CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A19*1 or A18*2 inverter with converter assembly connector.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL


*1: for LHD

*2: for RHD


c.

Disconnect the A17 EV control ECU connector.


Procedure1

a.
A481486C03
0.979,0.063 1.417,0.406 0.438,0.344 2.021,2.115 2.438,2.458 0.417,0.344 1.927,0.063 2.365,0.406 0.438,0.344 2.688,4.354 2.5,4.01 true 1.531,1.74 1.396,1.188 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.208,2.083 0.521,2.281 0.313,0.198 10 false *b 1.438,1.792 1.75,2.01 0.313,0.219 10 false ILKI 1.063,0.156 1.375,0.375 0.313,0.219 10 false A19 2.698,4.385 3.01,4.604 0.313,0.219 10 false ILK 2.115,2.208 2.427,2.427 0.313,0.219 10 false A17 2.021,0.146 2.333,0.365 0.313,0.219 10 false A18 1.469,0.146 1.781,0.344 0.313,0.198 10 false *A 2.417,0.146 2.729,0.344 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A19,A17)Location & Routing

Click Connector(A19)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A19-35 (ILKI) - A17-28 (ILK) Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A18,A17)Location & Routing

Click Connector(A18)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Inverter with Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A18-35 (ILKI) - A17-28 (ILK) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the A17 EV control ECU connector.


b.

Reconnect the A19*1 or A18*2 inverter with converter assembly connector.

*1: for LHD

*2: for RHD



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR