Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C7396  Motor Electronics Coolant Pump "A" Component Internal Failure  


DTC SUMMARY

MALFUNCTION DESCRIPTION


This DTC is stored when the water with motor pump assembly is malfunctioning. The cause of this malfunction may be one of the following:

Water with motor pump assembly malfunction
·

Water with motor pump assembly internal malfunction

·

Open or short in wire harness

·

Improperly connected connector

·

Frozen


EV cooling system malfunction
·

Foreign matter in water with motor pump assembly


HINT:

If this DTC is stored, the driving torque may be restricted.



DESCRIPTION

The water with motor pump assembly transmits rotation speed information to the EV control ECU. The EV control ECU monitors the speed and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure The water with motor pump assembly revolution speed is abnormally high or low (or stopped) for 1 minute or more.
(1 trip detection logic)
·

Inverter cooling system

·

Wire harness or connector

·

Water with motor pump assembly

·

EV control ECU


Master Warning:
Comes on
EV A

HINT:

The water with motor pump assembly operates when the ignition switch is ON (READY).


Related Data List
DTC No. Data List
P0C7396
·

Inverter Water Pump Revolution

·

Inverter Water Pump Duty Ratio

·

Inverter Coolant Water Temperature



Related Active Test
DTC No. Active Test
P0C7396 Activate the Inverter Water Pump

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

Wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A479462E03
5.938,5.198 7.052,5.51 1.115,0.313 10 false EV Control ECU 5.823,4.688 6.135,4.885 0.313,0.198 10 false E1 5.823,4.01 6.385,4.25 0.563,0.24 10 false MREL 5.823,2.229 6.385,2.469 0.563,0.24 10 false NIWP 5.823,0.75 6.385,0.99 0.563,0.24 10 false IWP 6.573,1.875 6.896,2.146 0.323,0.271 10 false +B 6.708,3.458 7.031,3.729 0.323,0.271 10 false +B 5.458,4.688 5.771,4.885 0.313,0.198 10 false A17 5.552,4.479 5.865,4.677 0.313,0.198 10 false 4 2.74,3.333 3.052,3.531 0.313,0.198 10 false B27 5.521,3.906 5.833,4.104 0.313,0.198 10 false 21 5.469,2.333 5.781,2.531 0.313,0.198 10 false A17 5.458,0.833 5.771,1.031 0.313,0.198 10 false A17 5.5,2.115 5.813,2.313 0.313,0.198 10 false 10 5.51,0.604 5.823,0.802 0.313,0.198 10 false 30 5.104,3.094 5.417,3.292 0.313,0.198 10 false 1 4.688,2.979 5.135,3.229 0.448,0.25 10 false GND 4.667,2.229 5.229,2.469 0.563,0.24 10 false NWP 5.104,2.479 5.417,2.677 0.313,0.198 10 false 2 4.688,0.708 5.25,0.948 0.563,0.24 10 false SWP 5.104,0.958 5.417,1.156 0.313,0.198 10 false 3 3.25,1.313 4.177,1.656 0.927,0.344 10 false Drive Circuit 2.76,0.396 3.323,0.635 0.563,0.24 10 false +BWP 2.552,0.625 2.865,0.823 0.313,0.198 10 false 4 1.646,4.469 2.427,4.802 0.781,0.333 10 false IGCT NO.2 1.792,2.208 2.76,2.427 0.969,0.219 10 false IGCT NO.5 1.865,1.01 2.177,1.208 0.313,0.198 10 false 1 1.875,0.646 2.188,0.844 0.313,0.198 10 false 3 0.417,3.042 1.073,3.229 0.656,0.188 10 false R/B FR 0.583,5.719 1.99,5.979 1.406,0.26 10 false Auxiliary Battery 1.792,5.875 5.958,6.063 4.167,0.188 10 false IWP: Water with motor pump assembly drive duty 1.792,6.323 6.052,6.552 4.26,0.229 10 false NIWP: Water with motor pump assembly speed signal 2.719,3.5 5.156,3.74 2.438,0.24 10 false Water with Motor Pump Assembly 5.5,4.115 5.813,4.313 0.313,0.198 10 false A8 0.417,1.688 1.604,1.875 1.188,0.188 10 false INV W/PMP 1.146,1.24 1.958,1.458 0.813,0.219 10 false INV W/PMP 1.094,0.646 1.406,0.844 0.313,0.198 10 false 5 1.094,1.01 1.406,1.208 0.313,0.198 10 false 2 2.333,3.719 2.646,3.917 0.313,0.198 10 false 5 1.542,3.719 1.854,3.917 0.313,0.198 10 false 3 2.333,4.24 2.646,4.438 0.313,0.198 10 false 2 1.542,4.24 1.854,4.438 0.313,0.198 10 false 1 0.146,1.563 0.458,1.76 0.313,0.198 10 false 2 0.135,1.813 0.448,2.01 0.313,0.198 10 false 1 0.885,3.448 1.198,3.646 0.313,0.198 10 false 1 2.604,2.323 2.917,2.521 0.313,0.198 10 false 1 1.125,3.448 1.438,3.646 0.313,0.198 10 false 2 2.604,2.083 2.917,2.281 0.313,0.198 10 false 2 0.719,3.75 1.458,4.042 0.74,0.292 10 false IGCT NO.2 0.615,4.802 1.625,5 1.01,0.198 10 false R/B RR#2 0.427,2.385 1.958,2.583 1.531,0.198 10 false R/B-B NO.1

for RHD:
A479462E05
5.938,5.198 7.052,5.51 1.115,0.313 10 false EV Control ECU 5.823,4.698 6.135,4.896 0.313,0.198 10 false E1 5.823,4.01 6.385,4.25 0.563,0.24 10 false MREL 5.823,2.271 6.385,2.51 0.563,0.24 10 false NIWP 5.823,0.76 6.385,1 0.563,0.24 10 false IWP 6.573,1.875 6.896,2.146 0.323,0.271 10 false +B 6.708,3.458 7.031,3.729 0.323,0.271 10 false +B 5.479,4.708 5.792,4.906 0.313,0.198 10 false A17 5.552,4.49 5.865,4.688 0.313,0.198 10 false 4 2.74,3.333 3.052,3.531 0.313,0.198 10 false B27 5.51,3.917 5.823,4.115 0.313,0.198 10 false 21 5.469,2.354 5.781,2.552 0.313,0.198 10 false A17 5.469,0.844 5.781,1.042 0.313,0.198 10 false A17 5.51,2.135 5.823,2.333 0.313,0.198 10 false 10 5.5,0.625 5.813,0.823 0.313,0.198 10 false 30 5.104,3.094 5.417,3.292 0.313,0.198 10 false 1 4.74,2.979 5.188,3.229 0.448,0.25 10 false GND 4.729,2.25 5.292,2.49 0.563,0.24 10 false NWP 5.104,2.479 5.417,2.677 0.313,0.198 10 false 2 4.729,0.75 5.292,0.99 0.563,0.24 10 false SWP 5.104,0.958 5.417,1.156 0.313,0.198 10 false 3 3.25,1.313 4.177,1.656 0.927,0.344 10 false Drive Circuit 2.76,0.417 3.323,0.656 0.563,0.24 10 false +BWP 2.563,0.635 2.875,0.833 0.313,0.198 10 false 4 1.646,4.469 2.427,4.802 0.781,0.333 10 false IGCT NO.2 1.792,2.219 2.76,2.438 0.969,0.219 10 false IGCT NO.5 1.865,1.01 2.177,1.208 0.313,0.198 10 false 1 1.875,0.646 2.188,0.844 0.313,0.198 10 false 3 0.417,3.042 1.073,3.229 0.656,0.188 10 false R/B FR 0.583,5.719 1.99,5.979 1.406,0.26 10 false Auxiliary Battery 1.792,5.875 5.958,6.063 4.167,0.188 10 false IWP: Water with motor pump assembly drive duty 1.792,6.323 6.052,6.552 4.26,0.229 10 false NIWP: Water with motor pump assembly speed signal 2.719,3.5 5.156,3.74 2.438,0.24 10 false Water with Motor Pump Assembly 5.469,4.115 5.781,4.313 0.313,0.198 10 false D15 0.417,1.708 1.604,1.896 1.188,0.188 10 false INV W/PMP 1.156,1.25 1.969,1.469 0.813,0.219 10 false INV W/PMP 1.094,0.646 1.406,0.844 0.313,0.198 10 false 5 1.094,1.01 1.406,1.208 0.313,0.198 10 false 2 2.333,3.719 2.646,3.917 0.313,0.198 10 false 5 1.542,3.719 1.854,3.917 0.313,0.198 10 false 3 2.333,4.24 2.646,4.438 0.313,0.198 10 false 2 1.542,4.24 1.854,4.438 0.313,0.198 10 false 1 0.146,1.563 0.458,1.76 0.313,0.198 10 false 2 0.156,1.813 0.469,2.01 0.313,0.198 10 false 1 0.885,3.479 1.198,3.677 0.313,0.198 10 false 1 2.594,2.344 2.906,2.542 0.313,0.198 10 false 1 1.125,3.479 1.438,3.677 0.313,0.198 10 false 2 2.594,2.104 2.906,2.302 0.313,0.198 10 false 2 0.708,3.76 1.448,4.052 0.74,0.292 10 false IGCT NO.2 0.615,4.802 1.625,5 1.01,0.198 10 false R/B RR#2 0.469,2.354 2,2.552 1.531,0.198 10 false R/B-B NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the water with motor pump assembly may suspend control as a self-protection function and store DTCs.

(When the auxiliary battery voltage returns to normal, the water with motor pump assembly will resume normal operation. In this case it is not necessary to replace the water with motor pump assembly.)

·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P0C7396 only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs including pending DTCs are also output. B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P06881F ECM/PCM Power Relay Sense Circuit Intermittent
Sensor and actuator circuit malfunction P314A31 Motor Electronics Coolant Pump "A" No Signal

HINT:

P0C7396 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




Post-procedure1

a.

Turn the ignition switch off.



A

2.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:
·

When the auxiliary battery voltage is low, the water with motor pump assembly may not operate.

·

When the water with motor pump assembly signal line (SWP - IWP) is open or its connection is faulty, the water with motor pump assembly is operated forcibly.



Pre-procedure1

a.

None.


Procedure1

a.

According to the display on the GTS, read the Data List.

Powertrain > EV > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60
HINT:

When the water with motor pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.


Result:
Result Proceed to
The value of Inverter Water Pump Revolution is 200 rpm or less A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CLEAR DTC

B

8.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.READ VALUE USING GTS (ACTIVATE THE INVERTER WATER PUMP)
4.READ VALUE USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the EV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.



HINT:

When the auxiliary battery voltage is low, the water with motor pump assembly may not operate.


Pre-procedure1

a.

Select the Data List item "Inverter Water Pump Revolution".

Powertrain > EV > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump
Inverter Water Pump Revolution
50004 397 1 30,60

Procedure1

a.

According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and, check the value of the Data List item "Inverter Water Pump Revolution".

Result:
Result Proceed to
The value of Inverter Water Pump Revolution is between 3200 and 8600 rpm A
None of the above conditions are met B


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the water with motor pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.




Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK EV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

8.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
5.CHECK EV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

Pre-procedure1

a.

Read the freeze frame data item Ambient Temperature using the GTS.

Powertrain > EV
Tester Display Measurement Item Range
Ambient Temperature Ambient air temperature -40 to 215°C
Powertrain > EV > DTC(P0C7396) > Freeze Frame Data
Tester Display
Ambient Temperature
50040 397 22 P0C7396

Procedure1

a.

Check if the freeze frame data item Ambient Temperature is below the freezing temperature of the EV coolant.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the EV coolant. A
Ambient Temperature value is below freezing temperature of the EV coolant. B


HINT:
·

EV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and EV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the EV coolant freezes in the EV radiator or water with motor pump, the coolant temperature in the inverter with converter assembly rises because the EV coolant cannot circulate. As a result, a DTC may be stored.

·

A DTC is stored when the water with motor pump impeller cannot rotate due to freezing of the EV coolant.

·

If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.




Post-procedure1

a.

None.



A

6.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

B

6.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

7.ADD EV COOLANT AND PERFORM AIR BLEEDING
7.ADD EV COOLANT AND PERFORM AIR BLEEDING
HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END

8.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

9.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

9.CHECK CONNECTOR CONNECTION CONDITION (WATER WITH MOTOR PUMP ASSEMBLY CONNECTOR)
a.
A480832

Check the connector connections and contact pressure of the relevant terminals for the water with motor pump assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely, the terminals are not deformed or corroded and there are no contact problems.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

NG

CONNECT SECURELY

10.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV control ECU connector.


b.

Disconnect the B27 water with motor pump assembly connector.


Procedure1

a.
A479463C04
1.51,2.958 1.938,3.25 0.427,0.292 2.031,0.083 2.479,0.417 0.448,0.333 1.677,4.24 1.813,3.792 true 2.677,2.385 2.438,2.031 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 0.188,2.906 0.5,3.063 0.313,0.156 10 false *b 1.625,3.042 1.938,3.24 0.313,0.198 10 false B27 1.542,4.25 2,4.448 0.458,0.198 10 false SWP 2.146,0.198 2.458,0.396 0.313,0.198 10 false A17 2.667,2.427 3.125,2.625 0.458,0.198 10 false IWP
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to Water with Motor Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A17,B27)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(B27)Engine Compartment>No. 2 Stack Wire>Water Pump with Motor Assembly

A17-30 (IWP) - B27-3 (SWP) Ignition switch off Below 1 Ω
A17-30 (IWP) or B27-3 (SWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B27 water with motor pump assembly connector.


b.

Reconnect the A17 EV control ECU connector.



OK

11.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the water with motor pump assembly may not operate.


Pre-procedure1

a.
C373943C02
2.021,2.042 2.604,2.625 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 2.656,2.583 2.969,2.74 0.313,0.156 10 false *2
*1 No. 1 front compartment relay block
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from No. 1 front compartment relay block.


Procedure1

a.

According to the display on the GTS, read the Data List.

Powertrain > EV > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60
Result:
Result Proceed to
The value of Inverter Water Pump Revolution is 200 rpm or less A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.


b.

Install the INV W/PMP fuse.



A

12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

B

12.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - WATER WITH MOTOR PUMP ASSEMBLY)

Pre-procedure1

a.

Disconnect the A17 EV Control ECU connector.


b.

Remove the INV W/PMP relay from the No. 1 front compartment relay block.


c.
A479465C01
0.083,0.083 0.396,0.24 0.313,0.156 10 false *1 2.688,0.479 3,0.635 0.313,0.156 10 false *2
*1 No. 1 front compartment relay block
*2 INV W/PMP Relay


Connect terminals 3 and 5 of the INV W/PMP relay holder.

HINT:

Make a short circuit between terminals 3 and 5 to supply +B voltage to the water with motor pump.



Procedure1

a.
A478495C02
2.021,0.583 2.438,0.948 0.417,0.365 2.604,2.958 2.375,2.521 true 1.917,2.969 2.219,2.313 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 2.625,3 3.083,3.198 0.458,0.198 10 false IWP 1.792,3 2.25,3.198 0.458,0.198 10 false E1 2.125,0.688 2.583,0.885 0.458,0.198 10 false A17
*a Rear view of wire harness connector
(to EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-30 (IWP) - A17-4 (E1) INV W/PMP relay holder terminals 3 and 5 connected
Ignition switch off
11 to 14 V


NOTICE:

Make sure to check for and clear DTCs after performing this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the INV W/PMP relay.


b.

Reconnect the A17 EV control ECU connector.



OK

13.CHECK EV CONTROL ECU (CHECK WAVEFORM)

NG

16.REPLACE WATER WITH MOTOR PUMP ASSEMBLY
13.CHECK EV CONTROL ECU (CHECK WAVEFORM)

Pre-procedure1

a.

Connect an oscilloscope between the EV control ECU terminals specified in the table below.


b.

Turn the ignition switch to ON.


Procedure1

a.
A478491C35
1.969,0.875 2.406,1.188 0.438,0.313 2.219,1.688 1.99,2.51 true 2.375,1.896 2.688,2.542 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.906,2.552 2.354,2.719 0.448,0.167 10 false E1 2.698,2.563 3.146,2.729 0.448,0.167 10 false IWP 2.083,0.969 2.385,1.135 0.302,0.167 10 false A17
*a Component with harness connected
(EV Control ECU)


While turning the ignition switch to ON, check the waveform between the EV control ECU terminals.

Tester Connection Condition Equipment Setting

Click Location & Routing(A17)Location & Routing

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A17-30 (IWP) - A17-4 (E1) Ignition switch ON 5 V/DIV., 50 ms./DIV.

OK:

Waveform duty ratio is between 3% and 9%.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

14.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NG

14.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

15.ADD EV COOLANT AND PERFORM AIR BLEEDING
15.ADD EV COOLANT AND PERFORM AIR BLEEDING
HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END

16.REPLACE WATER WITH MOTOR PUMP ASSEMBLY

NEXT

17.ADD EV COOLANT AND PERFORM AIR BLEEDING
17.ADD EV COOLANT AND PERFORM AIR BLEEDING
HINT:

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter Coolant)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END