Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C7600  Hybrid/EV Battery System Discharge Time Too Long  


DTC SUMMARY

MALFUNCTION DESCRIPTION


When the ignition switch is turned from ON (READY) to off, the EV control ECU detect that the high-voltage capacitor inside the inverter with converter assembly is not discharged.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction

Inverter with converter assembly malfunction


Shutdown signal circuit malfunction
·

EV control ECU malfunction

·

Wire harness malfunction

·

Inverter with converter assembly malfunction

·

FCDC converter control ECU malfunction



DESCRIPTION

Refer to the description for DTC P0D2D16.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0D2D16

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P0C7600 Hybrid/EV Battery System Discharge Time Too Long The inverter voltage (VH) does not drop during discharge.
(Discharge: Offsetting of the residual pressure in the high-voltage side after ignition switch is turned off)
(1 trip detection logic)
·

Inverter with converter assembly

·

Wire harness or connector

·

EV control ECU


Master Warning:
Comes on
EV A

HINT:

When theignition switch is turned from ON (READY) to off, the MG ECU discharges voltage stored in the inverter by allowing current to flow to motor (MG2) without generating torque. When the vehicle is normal, VH voltage becomes approximately 0 V after discharging. If VH voltage exceeds a specified value, this DTC is stored.


A111758E07
3.615,1.542 3.729,1.438 false 3.906,2.073 4.354,1.854 false 2.031,0.698 2.208,0.854 0.177,0.156 10 IG 2.635,0.583 2.875,0.74 0.24,0.156 10 ON 3.063,0.802 3.365,0.958 0.302,0.156 10 OFF 2,1.333 2.219,1.49 0.219,0.156 10 VH 3.771,1.365 4.531,1.615 0.76,0.25 10 Abnormal 3.208,2.344 4.417,2.594 1.208,0.25 10 During Discharge 4.396,1.76 5,2 0.604,0.24 10 Normal

Related Data List
DTC No. Data List
P0C7600 VH-Voltage after Boosting
FC Converter Shutdown Status

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 10 minutes or more.

5.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the shut down signal circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
P0C7600 only is output, or DTCs except the ones in the table below are also output. A
Any hybrid control system DTCs in the table below are output B
Any FC control system DTCs in the table below are output C


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P0A1B04 Drive Motor "A" Control Module System Internal Failure
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F04 FC Air Compressor Motor Control Module System Internal Failure
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E8649 FC Air Compressor Motor Position Sensor Internal Electronic Failure
P1C731C Sensor Reference Voltage "H" Circuit/Open Circuit Voltage Out of Range
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06B01C Sensor Power Supply "A" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A1B00 Drive Motor "A" Control Module Performance
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P1CB300 Drive Motor "A" Position Sensor REF Signal Oscillation Stop
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P1D8F00 FC Air Compressor Motor Control Module Performance
P1E8738 FC Air Compressor Motor Position Sensor REF Signal Frequency Incorrect
P1E8800 FC Air Compressor Motor Position Sensor REF Signal Oscillation Stop
P1D7516 FC Air Compressor Motor Position Sensor Circuit Voltage Below Threshold
P1D7522 FC Air Compressor Motor Position Sensor Signal Amplitude > Maximum
P1D751C FC Air Compressor Motor Position Sensor Circuit Voltage Out of Range
FC control system P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
System malfunction Hybrid control system P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P1E1500 FC Positive Contactor Actuator Stuck Closed
P1E1773 FC Negative Contactor Control Actuator Stuck Closed
P1E1573 FC Positive and Negative Contactor Actuator Stuck Closed
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Overvoltage Signal Stuck On
P1D9514 FC Converter Shutdown Signal Circuit Short to Ground or Open
P1D9512 FC Converter Shutdown Signal Circuit Short to Battery
P1E0A14 FC Converter Fail Signal Circuit Short to Ground or Open
P1E0A12 FC Converter Fail Signal Circuit Short to Battery
FC control system P1D0619 FC Converter Phase U Current Circuit Current Above Threshold
P1DDA4B FC Converter Phase U Over Temperature
P1DDA9E FC Converter Phase U Fail Signal Stuck On
P1D0719 FC Converter Phase V Current Circuit Current Above Threshold
P1DDB4B FC Converter Phase V Over Temperature
P1DDB9E FC Converter Phase V Fail Signal Stuck On
P1D0819 FC Converter Phase W Current Circuit Current Above Threshold
P1DDC4B FC Converter Phase W Over Temperature
P1DDC9E FC Converter Phase W Fail Signal Stuck On
P1D0919 FC Converter Phase X Current Circuit Current Above Threshold
P1DDD4B FC Converter Phase X Over Temperature
P1DDD9E FC Converter Phase X Fail Signal Stuck On
P1F0117 FC Converter Output Voltage Circuit Voltage Above Threshold
P1F009E FC Converter Overvoltage Signal Stuck On

HINT:
·

P0C7600 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (EV)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CHECK FREEZE FRAME DATA (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P0C7600.

Powertrain > EV
Tester Display Measurement Item Range
FC Converter Shutdown Status FC boost converter shutdown status ON/OFF
Powertrain > EV > DTC(P0C7600) > Freeze Frame Data
Tester Display
FC Converter Shutdown Status
50040 397 860 P0C7600
NOTICE:

As freeze frame data is stored immediately before and after a DTC is stored, make sure to only read the values for the moment the DTC was stored ("0(s)").


Result:
Result Proceed to
FC Converter Shutdown Status is OFF A
FC Converter Shutdown Status is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK EV CONTROL ECU

B

6.READ VALUE USING GTS (VH-VOLTAGE AFTER BOOSTING)
3.CHECK EV CONTROL ECU

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

OK

5.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INVERTER WITH CONVERTER ASSEMBLY

OK

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

6.READ VALUE USING GTS (VH-VOLTAGE AFTER BOOSTING)

Pre-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.


Procedure1

a.

Read the value of "VH-Voltage after Boosting" displayed on the GTS.

Powertrain > EV > Data List
Tester Display Measurement Item Range
VH-Voltage after Boosting High voltage after it is boosted -
Powertrain > EV > Data List
Tester Display
VH-Voltage after Boosting
50003 397 151
Result:
Result Proceed to
The value of VH-Voltage after Boosting is less than 50 V. A
None of the above conditions are met B



Post-procedure1

a.

None.



A

3.CHECK EV CONTROL ECU

B

7.CLEAR DTC
7.CLEAR DTC

NEXT

8.CHECK DTC OUTPUT (EV)
8.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D9512 or P1E0A12 is output A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

CHECK FOR GO TO DTC CHART (HYBRID CONTROL SYSTEM)

B

3.CHECK EV CONTROL ECU