Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1D9512  FC Converter Shutdown Signal Circuit Short to Battery  P1D9514  FC Converter Shutdown Signal Circuit Short to Ground or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects malfunctions in the disconnect signal (FSDN signal) to the FCDC converter control ECU.

The cause of this malfunction may be one of the following:

FSDN signal circuit malfunction
·

Wire harness malfunction

·

FCDC converter control ECU malfunction

·

EV Control ECU malfunction



DESCRIPTION

Refer to the wiring diagram for DTC P321E9F.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P321E9F

Refer to boost system diagram for the System Description.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>SYSTEM DESCRIPTION

If necessary, the EV control ECU shuts off the operation of the FC converter power module transistor by sending the shut off signal (FSDN signal) to the FCDC converter control ECU.

If only either of the inverter with converter assembly and the FC converter power module transistor is shut off, difference in voltage may occur, and this may cause malfunctions such as a fuse blow. To prevent this, if the FCDC converter control ECU detects the shut off of the FC converter power module transistor, it immediately sends the converter fail signal (ISDN signal) to the EV control ECU.

When the EV control ECU receives the ISDN signal, it sends the HSDN signal (MG shut down signal) to the motor generator control ECU (MG ECU), and then shuts off the power supply to both the drive motor and FC air compressor motor, simultaneously.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D9512 FC Converter Shutdown Signal Circuit Short to Battery The FSDN signal from the EV control ECU is OFF but the CPU monitored value of the ISDN signal is ON.
(1 trip detection logic)
·

Wire harness or connector

·

EV Control ECU

·

FCDC converter control ECU board sub-assembly


Master Warning:
Comes on
EV A
P1D9514 FC Converter Shutdown Signal Circuit Short to Ground or Open The FSDN signal from the EV control ECU is ON but the CPU monitored value of the ISDN signal is OFF.
(1 trip detection logic)
·

Wire harness or connector

·

EV Control ECU

·

FCDC converter control ECU board sub-assembly


Master Warning:
Comes on
EV A

Related Data List
DTC No. ECU Data List
P1D9512
P1D9514
·

FC Emergency Shutdown Signal

·

FC Converter Shutdown Request



CONFIRMATION DRIVING PATTERN

HINT:

After the repair, perform the following procedure to confirm the repair.


1.

Turn the ignition switch off and wait for 10 minutes or more.

2.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

3.

Turn the ignition switch off and wait for 10 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the Shut Down Signal Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Shut Down Signal Circuit

A480868E01
3.125,0.583 3.583,0.781 0.458,0.198 10 false B6 3.115,3.5 3.573,3.698 0.458,0.198 10 false B6 0.479,5.042 0.938,5.24 0.458,0.198 10 false B5 3.125,1.354 3.583,1.552 0.458,0.198 10 false B6 3.125,1.896 3.583,2.094 0.458,0.198 10 false B6 3.125,2.427 3.594,2.625 0.469,0.198 10 false B6 3.125,2.958 3.583,3.156 0.458,0.198 10 false B6 0.469,1.354 0.927,1.552 0.458,0.198 10 false B6 0.469,1.896 0.927,2.094 0.458,0.198 10 false B6 4.01,2.958 4.469,3.156 0.458,0.198 10 false A17 6.594,3.052 7.052,3.25 0.458,0.198 10 false A17 4.01,3.49 4.469,3.688 0.458,0.198 10 false A16 4.021,4.031 4.479,4.229 0.458,0.198 10 false A16 2.604,0.583 3.063,0.781 0.458,0.198 10 false IG2 2.573,1.365 3.031,1.563 0.458,0.198 10 false +B1 2.573,1.906 3.031,2.104 0.458,0.198 10 false +B2 2.458,2.427 2.917,2.625 0.458,0.198 10 false DRN0 2.51,3.406 2.969,3.604 0.458,0.198 10 false ISDN 2.448,2.865 2.906,3.063 0.458,0.198 10 false FSDN 2.104,3.073 2.563,3.271 0.458,0.198 10 false +B 1.125,3.219 1.583,3.417 0.458,0.198 10 false CPU 0.948,1.354 1.406,1.552 0.458,0.198 10 false E1 0.948,1.896 1.406,2.094 0.458,0.198 10 false E2 0.469,1.177 0.927,1.375 0.458,0.198 10 false 10 0.469,1.708 0.927,1.906 0.458,0.198 10 false 11 0.771,5.052 1.229,5.25 0.458,0.198 10 false WGND 3.156,2.781 3.594,2.979 0.438,0.198 10 false 1 3.156,3.333 3.594,3.531 0.438,0.198 10 false 4 3.188,2.26 3.625,2.458 0.438,0.198 10 false 2 3.135,1.698 3.573,1.896 0.438,0.198 10 false 13 3.125,1.167 3.563,1.365 0.438,0.198 10 false 12 3.167,0.385 3.604,0.583 0.438,0.198 10 false 6 4.094,2.76 4.531,2.958 0.438,0.198 10 false 2 4.063,3.323 4.5,3.521 0.438,0.198 10 false 20 4.052,3.854 4.49,4.052 0.438,0.198 10 false 22 4.344,4.031 4.781,4.229 0.438,0.198 10 false DRN3 4.354,3.396 4.813,3.594 0.458,0.198 10 false ISDN 4.354,2.865 4.813,3.063 0.458,0.198 10 false FSDN 4.844,2.417 5.302,2.615 0.458,0.198 10 false +B 5.74,3.042 6.198,3.24 0.458,0.198 10 false CPU 6.135,2.958 6.594,3.156 0.458,0.198 10 false HSDN 6.677,2.854 6.865,3.063 0.188,0.208 10 false 8 4.979,4.552 6.615,4.938 1.635,0.385 10 false EV Control ECU 1.24,5.51 3.542,5.948 2.302,0.438 10 false FC Converter Assembly 0.99,3.99 2.781,4.51 1.792,0.521 10 false FCDC Converter Control ECU Board Sub-assembly 4.125,5.458 6.385,5.74 2.26,0.281 10 false to Inverter with Converter Assembly 4.531,0.573 6.833,1.01 2.302,0.438 10 false from FCDC-IG2 Fuse 4.51,1.344 6.813,1.781 2.302,0.438 10 false from IGCT NO. 7 Fuse 0.542,4.333 1,4.531 0.458,0.198 10 false 2 0.531,4.854 0.99,5.052 0.458,0.198 10 false 2 0.479,4.51 0.938,4.708 0.458,0.198 10 false B3 0.771,4.51 1.229,4.708 0.458,0.198 10 false HGND

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
P1D9512 or P1D9514 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of FC control system in the tables below are output. C

Malfunction Content System Relevant DTC
Micro computer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
FC control system P060B49 Internal Control Module A/D Processing Performance Internal Electronic Failure
P060B71 Internal Control Module A/D Processing Performance Actuator Stuck
P060B1C Internal Control Module A/D Processing Performance Circuit Voltage Out of Range
P060B16 Internal Control Module A/D Processing Performance Circuit Voltage Below Threshold
Power source circuit malfunction FC control system P1F451F FC Converter Control Module Power Relay Sense Circuit Intermittent
P1F651C FC Converter Control Module Power Supply (-5V) Circuit Voltage Out of Range
P1F661C FC Converter Control Module Power Supply (+V5AREF) Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
FC control system U116087 Lost Communication with Hydrogen Filling Control Module Missing Message
U029387 Lost Communication with Hybrid/EV Powertrain Control Module Missing Message


HINT:
·

The chart above is listed in inspection order of priority.

·

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

2.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

3.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - FC CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481473

Disconnect the B6 FC converter assembly connector.


d.

Disconnect the A17 EV Control ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A480867C01
1.688,0.281 2.094,0.594 0.406,0.313 5.635,0.438 6.094,0.771 0.458,0.333 6.313,2.281 5.927,1.875 true 1.26,2.156 1.75,1.271 true 0.542,0.26 0.854,0.458 0.313,0.198 10 false *a 3.219,0.292 3.531,0.49 0.313,0.198 10 false *b 1.823,0.375 2.281,0.573 0.458,0.198 10 false B6 0.938,2.198 1.49,2.417 0.552,0.219 10 false FSDN 5.76,0.552 6.219,0.75 0.458,0.198 10 false A17 6.302,2.333 6.854,2.552 0.552,0.219 10 false FSDN
*a Front view of wire harness connector
(to FC Converter Assembly)
*b Rear view of wire harness connector
(to EV Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B6,A17)Location & Routing

Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

Click Connector(A17)Instrument Panel>Front Compartment Main Wire>EV Control ECU

B6-1 (FSDN) - A17-2 (FSDN) Ignition switch off Below 1 Ω
B6-1 (FSDN) or A17-2 (FSDN) - Body ground and other terminals Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B6 FC converter assembly connector.


b.

Reconnect the A17 EV Control ECU connector.


c.

Install the electric heater sub-assembly.



OK

5.CHECK FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY (CHECK FOR SHORT TO +B OR GND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY (CHECK FOR SHORT TO +B OR GND)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481473

Disconnect the B6 FC converter assembly connector.


Procedure1

a.
A491111C04
1.458,0.396 1.948,0.802 0.49,0.406 1.052,2.688 1.469,1.979 true 1.417,2.667 1.646,1.979 true 2.01,2.656 1.823,1.948 true 2.323,2.656 1.99,1.948 true 2.531,2.177 1.833,1.479 true 0.823,2.198 1.646,1.635 true 2.677,1.833 2.01,1.469 true 1.625,0.521 1.938,0.719 0.313,0.198 10 false B6 1.979,2.667 2.26,2.865 0.281,0.198 10 false E1 2.583,2.177 3.198,2.375 0.615,0.198 10 false DRN0 0.573,2.177 1.188,2.375 0.615,0.198 10 false IG2 2.365,2.667 2.635,2.865 0.271,0.198 10 false E2 0.802,2.677 1.167,2.875 0.365,0.198 10 false +B2 1.26,2.677 1.635,2.885 0.375,0.208 10 false +B1 0.281,0.396 0.896,0.594 0.615,0.198 10 false *a 2.698,1.823 3.313,2.021 0.615,0.198 10 false FSDN
*a Component without harness connected
(FC Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B6)Location & Routing

Click Connector(B6)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B6-1 (FSDN) - B6-10 (E1) Ignition switch off 2.65 to 3.55 kΩ
B6-1 (FSDN) - B6-12 (+B1) Ignition switch off 5 kΩ or higher
B6-1 (FSDN) - B6-2 (DRN0) Ignition switch off 10 kΩ or higher
B6-1 (FSDN) - B6-11 (E2) Ignition switch off 10 kΩ or higher
B6-1 (FSDN) - B6-13 (+B2) Ignition switch off 5 kΩ or higher
B6-1 (FSDN) - B6-6 (IG2) Ignition switch off 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the B6 FC converter assembly connector.


b.

Install the electric heater sub-assembly.



OK

NG

6.REMOVE FC CONVERTER ASSEMBLY
6.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY