Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U011187  Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message  


DESCRIPTION

The EV control ECU transmits and receives signals via CAN communication to and from the battery ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message The EV control ECU cannot receive signals from the battery ECU assembly
(1 trip detection logic)
·

Battery ECU assembly

·

EV control ECU

·

Wire harness or connector


Master Warning:
Comes on
EV B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

for LHD:
A481436E01
1.115,4.313 2.729,4.667 1.615,0.354 10 false EV Control ECU 0.719,6.365 2.5,6.625 1.781,0.26 10 false : CAN Communication Line 4.094,3.885 5.521,4.25 1.427,0.365 10 false No. 2 EV Battery Pack Wire Connector 5.552,4.76 7.094,5 1.542,0.24 10 false Battery ECU Assembly 4.083,3.698 4.542,3.896 0.458,0.198 10 false G156 3.323,1.365 4.125,1.531 0.802,0.167 10 false IGCT NO.6 2.448,2.031 3.25,2.198 0.802,0.167 10 false IGCT NO.2 1.25,1.333 2.052,1.5 0.802,0.167 10 false IGCT NO.2 0.625,4.781 1.5,4.938 0.875,0.156 10 false R/B RR #2 0.771,5.5 2.031,5.75 1.26,0.25 10 false Auxiliary Battery 4.417,2.771 4.854,2.927 0.438,0.156 10 false CA1H 4.417,3.135 4.854,3.292 0.438,0.156 10 false CA1L 4.917,2.781 5.354,2.938 0.438,0.156 10 false CA1H 4.948,3.156 5.385,3.313 0.438,0.156 10 false CA1L 4.25,2.625 4.406,2.823 0.156,0.198 10 false 4 4.188,2.979 4.5,3.177 0.313,0.198 10 false 13 5.344,2.979 5.656,3.177 0.313,0.198 10 false 13 5.365,2.615 5.521,2.813 0.156,0.198 10 false 4 1.563,2.771 2,2.927 0.438,0.156 10 false CA4H 1.594,3.156 2.031,3.313 0.438,0.156 10 false CA4L 5.979,2.792 6.417,2.948 0.438,0.156 10 false CA1H 5.979,3.156 6.417,3.313 0.438,0.156 10 false CA1L 5.573,4.583 5.865,4.781 0.292,0.198 10 false z26 1.542,1.792 1.99,1.99 0.448,0.198 10 false MREL 5.729,1.115 6.042,1.313 0.313,0.198 10 false 40 2.042,2.625 2.354,2.823 0.313,0.198 10 false 2 2.031,2.99 2.344,3.188 0.313,0.198 10 false 3 5.729,2.615 6.042,2.813 0.313,0.198 10 false 16 5.75,2.979 6.063,3.177 0.313,0.198 10 false 15 1.438,0.49 1.594,0.688 0.156,0.198 10 false 1 1.677,0.49 1.833,0.688 0.156,0.198 10 false 2 3.719,1.083 3.875,1.281 0.156,0.198 10 false 2 3.479,1.083 3.635,1.281 0.156,0.198 10 false 1 2.385,1.698 2.542,1.896 0.156,0.198 10 false 2 3.073,1.698 3.229,1.896 0.156,0.198 10 false 1 2.385,1.094 2.542,1.292 0.156,0.198 10 false 3 3.083,1.104 3.24,1.302 0.156,0.198 10 false 5 2.021,1.698 2.354,1.906 0.333,0.208 10 false 21 5.99,1.208 6.396,1.385 0.406,0.177 10 false IGCT 1.125,4.125 1.563,4.281 0.438,0.156 10 false A8 1.438,1.083 1.594,1.281 0.156,0.198 10 false 1 1.677,1.083 1.833,1.281 0.156,0.198 10 false 2 1.24,0.76 2.615,0.969 1.375,0.208 10 false LUG-B NO.1 5.979,1.802 6.385,1.979 0.406,0.177 10 false GND 5.729,1.708 6.135,1.885 0.406,0.177 10 false 11 4.979,1.792 5.385,1.969 0.406,0.177 10 false GND 4.438,1.802 4.844,1.979 0.406,0.177 10 false GND 5.354,1.708 5.76,1.885 0.406,0.177 10 false 1 4.26,1.708 4.667,1.885 0.406,0.177 10 false 1 4.958,1.198 5.365,1.375 0.406,0.177 10 false IGCT 4.438,1.198 4.844,1.375 0.406,0.177 10 false IGCT 5.344,1.115 5.656,1.313 0.313,0.198 10 false 14 4.177,1.094 4.49,1.292 0.313,0.198 10 false 14 5.99,0.604 6.396,0.781 0.406,0.177 10 false AM 5.729,0.49 6.042,0.688 0.313,0.198 10 false 20 5.042,0.604 5.448,0.781 0.406,0.177 10 false AM 4.427,0.604 4.833,0.781 0.406,0.177 10 false AM 5.365,0.51 5.677,0.708 0.313,0.198 10 false 5 4.24,0.49 4.552,0.688 0.313,0.198 10 false 5 3.479,4.677 3.771,4.875 0.292,0.198 10 false A 3.813,4.688 4.104,4.885 0.292,0.198 10 false B

for RHD:
A481436E02
1.198,4.281 2.813,4.635 1.615,0.354 10 false EV Control ECU 0.719,6.417 2.5,6.677 1.781,0.26 10 false : CAN Communication Line 4.094,3.885 5.531,4.323 1.438,0.438 10 false No. 2 EV Battery Pack Wire Connector 5.552,4.76 7.094,5 1.542,0.24 10 false Battery ECU Assembly 4.083,3.698 4.542,3.896 0.458,0.198 10 false G156 3.323,1.365 4.125,1.531 0.802,0.167 10 false IGCT NO.6 2.448,2.031 3.25,2.198 0.802,0.167 10 false IGCT NO.2 1.25,1.333 2.052,1.5 0.802,0.167 10 false IGCT NO.2 0.625,4.781 1.5,4.938 0.875,0.156 10 false R/B RR #2 0.771,5.5 2.031,5.75 1.26,0.25 10 false Auxiliary Battery 4.417,2.781 4.854,2.938 0.438,0.156 10 false CA1H 4.427,3.146 4.865,3.302 0.438,0.156 10 false CA1L 4.906,2.781 5.344,2.938 0.438,0.156 10 false CA1H 4.938,3.156 5.375,3.313 0.438,0.156 10 false CA1L 4.25,2.646 4.406,2.844 0.156,0.198 10 false 4 4.188,3.01 4.5,3.208 0.313,0.198 10 false 13 5.344,3 5.656,3.198 0.313,0.198 10 false 13 5.365,2.635 5.521,2.833 0.156,0.198 10 false 4 1.563,2.781 2,2.938 0.438,0.156 10 false CA4H 1.573,3.167 2.01,3.323 0.438,0.156 10 false CA4L 5.979,2.792 6.417,2.948 0.438,0.156 10 false CA1H 5.979,3.156 6.417,3.313 0.438,0.156 10 false CA1L 5.573,4.583 5.865,4.781 0.292,0.198 10 false z26 1.531,1.792 1.979,1.99 0.448,0.198 10 false MREL 5.729,1.115 6.042,1.313 0.313,0.198 10 false 40 2.042,2.625 2.354,2.823 0.313,0.198 10 false 2 2.031,2.99 2.344,3.188 0.313,0.198 10 false 3 5.729,2.625 6.042,2.823 0.313,0.198 10 false 16 5.729,2.99 6.042,3.188 0.313,0.198 10 false 15 1.438,0.49 1.594,0.688 0.156,0.198 10 false 1 1.677,0.49 1.833,0.688 0.156,0.198 10 false 2 3.719,1.083 3.875,1.281 0.156,0.198 10 false 2 3.479,1.083 3.635,1.281 0.156,0.198 10 false 1 2.385,1.698 2.542,1.896 0.156,0.198 10 false 2 3.073,1.698 3.229,1.896 0.156,0.198 10 false 1 2.385,1.094 2.542,1.292 0.156,0.198 10 false 3 3.083,1.104 3.24,1.302 0.156,0.198 10 false 5 2.021,1.698 2.354,1.906 0.333,0.208 10 false 21 5.99,1.208 6.396,1.385 0.406,0.177 10 false IGCT 1.198,4.104 1.635,4.26 0.438,0.156 10 false D15 1.438,1.083 1.594,1.281 0.156,0.198 10 false 1 1.677,1.083 1.833,1.281 0.156,0.198 10 false 2 1.24,0.76 2.615,0.969 1.375,0.208 10 false LUG-B NO.1 5.979,1.802 6.385,1.979 0.406,0.177 10 false GND 5.729,1.708 6.135,1.885 0.406,0.177 10 false 11 4.969,1.792 5.375,1.969 0.406,0.177 10 false GND 4.438,1.781 4.844,1.958 0.406,0.177 10 false GND 5.354,1.708 5.76,1.885 0.406,0.177 10 false 1 4.26,1.708 4.667,1.885 0.406,0.177 10 false 1 4.969,1.188 5.375,1.365 0.406,0.177 10 false IGCT 4.438,1.188 4.844,1.365 0.406,0.177 10 false IGCT 5.344,1.115 5.656,1.313 0.313,0.198 10 false 14 4.177,1.094 4.49,1.292 0.313,0.198 10 false 14 5.99,0.604 6.396,0.781 0.406,0.177 10 false AM 5.729,0.49 6.042,0.688 0.313,0.198 10 false 20 5.052,0.594 5.458,0.771 0.406,0.177 10 false AM 4.438,0.604 4.844,0.781 0.406,0.177 10 false AM 5.365,0.51 5.677,0.708 0.313,0.198 10 false 5 4.24,0.49 4.552,0.688 0.313,0.198 10 false 5 3.479,4.677 3.771,4.875 0.292,0.198 10 false A 3.813,4.688 4.104,4.885 0.292,0.198 10 false B

A484688E01
0.479,2.427 4.146,2.625 3.667,0.198 10 false : CAN Communication Line 5.271,0.365 5.427,0.563 0.156,0.198 10 false A 5.792,0.385 5.948,0.583 0.156,0.198 10 false B 2.896,0.896 3.51,1.094 0.615,0.198 10 false CA2H 2.927,1.313 3.542,1.51 0.615,0.198 10 false CA2L 3.375,0.76 3.531,0.958 0.156,0.198 10 false 6 3.365,1.177 3.521,1.375 0.156,0.198 10 false 5 1.625,1.698 2.083,1.896 0.458,0.198 10 false D92 1.615,1.885 4.219,2.083 2.604,0.198 10 false Shift Control ECU

Refer to the wiring diagram for the ECU Power Source Circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>ECU Power Source Circuit

Refer to the wiring diagram for DTC P056014.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the electric vehicle charger assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV BATTERY)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK HARNESS AND CONNECTOR (AM, IGCT VOLTAGE)

B

2.CHECK HARNESS AND CONNECTOR (AM, IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 center floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



Procedure1

a.
C382282C15
1.51,2.427 2.01,2.823 0.5,0.396 2.49,3.49 2.844,3.188 true 1.729,3.875 2.74,4.26 true 1.74,3.49 0.823,2.729 0.823,2.729 0.708,2.729 true 0.135,0.104 0.354,0.292 0.219,0.188 10 true *a 1.604,2.552 2.115,2.729 0.51,0.177 10 false G156 2.906,3.094 3.292,3.26 0.385,0.167 10 false GND 2.823,4.219 3.26,4.427 0.438,0.208 10 false IGCT 0.448,2.667 0.719,2.865 0.271,0.198 10 false AM
*a Component with harness connected
(No. 2 EV Battery Pack Wire Connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-5 (AM) - G156-1 (GND) Ignition switch off 11 to 14 V
G156-14 (IGCT) - G156-1 (GND) Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery ECU assembly power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Install the No. 2 center floor to brace extension.



OK

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 center floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
C382281E07
2.729,0.208 3.198,0.552 0.469,0.344 2.802,0.302 3.177,0.469 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374188C22
1.542,0.24 2,0.563 0.458,0.323 0.677,1.802 1.594,1.385 true 0.677,0.646 1.594,1.115 true 0.26,0.573 0.875,0.771 0.615,0.198 10 false CA1H 0.354,1.781 0.969,1.979 0.615,0.198 10 false CA1L 1.615,0.333 2.073,0.531 0.458,0.198 10 false G156 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

G156-4 (CA1H) - G156-13 (CA1L) Ignition switch off 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the No. 2 center floor to brace extension.



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307E04
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374185C49
1.479,1.604 1.938,1.927 0.458,0.323 1.51,0.042 1.979,0.375 0.469,0.333 0.396,3.115 0.594,2.667 true 0.635,0.615 1.698,0.833 true 0.615,2.427 0.948,1.813 0.948,1.813 0.823,1.813 true 1.74,1.094 0.688,1.26 true 2.292,0.802 2.781,0.615 true 1.656,2.417 2.438,1.833 true 0.094,0.156 0.406,0.313 0.313,0.156 10 false *a 0.135,1.74 0.448,1.896 0.313,0.156 10 false *b 1.604,0.146 2.063,0.344 0.458,0.198 10 false G156 1.604,1.698 1.917,1.896 0.313,0.198 10 false z26 0.583,1.74 0.896,1.938 0.313,0.198 10 false AM 0.396,0.521 0.708,0.719 0.313,0.198 10 false AM 0.354,1.198 0.813,1.396 0.458,0.198 10 false IGCT 0.208,3.167 0.667,3.365 0.458,0.198 10 false IGCT 2.844,0.51 3.292,0.698 0.448,0.188 10 false GND 2.469,1.74 2.917,1.927 0.448,0.188 10 false GND
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,z26)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

G156-14 (IGCT) - z26-40 (IGCT) Always Below 1 Ω
G156-5 (AM) - z26-20 (AM) Always Below 1 Ω
G156-1 (GND) - z26-11 (GND) Always Below 1 Ω
G156-14 (IGCT) or z26-40 (IGCT) - Other terminals and body ground Always 10 kΩ or higher
G156-5 (AM) or z26-20 (AM) - Other terminals and body ground Always 10 kΩ or higher
G156-1 (GND) or z26-11 (GND) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 2 EV BATTERY PACK WIRE CONNECTOR - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 EV battery cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C373307E05
2.146,0.125 2.573,0.417 0.427,0.292 2.24,0.177 2.531,0.354 0.292,0.177 10 true z26

Disconnect the z26 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
C374185C50
1.521,1.635 1.969,1.958 0.448,0.323 1.49,0.042 1.958,0.354 0.469,0.313 1.052,2.417 0.823,1.792 0.823,1.792 0.719,1.792 true 1.177,2.49 0.604,3.135 true 1.896,0.813 2.729,0.344 true 1.885,1.104 2.698,1.427 true 1.646,1.729 1.958,1.927 0.313,0.198 10 false z26 1.583,0.135 2.042,0.333 0.458,0.198 10 false G156 0.313,1.719 0.927,1.917 0.615,0.198 10 false CA1H 2.781,0.25 3.396,0.448 0.615,0.198 10 false CA1H 0.219,3.073 0.833,3.271 0.615,0.198 10 false CA1L 2.75,1.365 3.365,1.563 0.615,0.198 10 false CA1L 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 0.135,1.521 0.448,1.677 0.313,0.156 10 false *b
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z26,G156)Location & Routing

Click Connector(z26)Body>other>EV Supply Battery Assembly , Battery ECU Assembly

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

z26-16 (CA1H) - G156-4 (CA1H) Always Below 1 Ω
z26-15 (CA1L) - G156-13 (CA1L) Always Below 1 Ω
z26-16 (CA1H) or G156-4 (CA1H) - Other terminals and body ground Always 10 kΩ or higher
z26-15 (CA1L) or G156-13 (CA1L) - Other terminals and body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z26 battery ECU assembly connector.


b.

Install the upper No. 1 EV battery cover sub-assembly.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 2 EV BATTERY PACK WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the EV control ECU and battery ECU assembly is not loose or disconnected.




c.

Disconnect the D92 shift control ECU connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Remove the No. 2 center floor to brace extension.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



e.
C382281E08
2.729,0.208 3.198,0.552 0.469,0.344 2.802,0.302 3.177,0.469 0.375,0.167 10 true G156

Disconnect the G156 No. 2 EV battery pack wire connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.
A479529C05
1.521,0.281 2.063,0.625 0.542,0.344 2.5,2.021 2.927,2.292 0.427,0.271 2.49,1.698 2.917,1.969 0.427,0.271 0.771,0.75 1.688,1.188 true 0.792,1.656 1.688,1.365 true 2.573,4.344 3,3.615 true 2.292,4 2.927,3.615 true 1.646,0.385 2.26,0.583 0.615,0.198 10 false G156 0.375,0.677 0.99,0.875 0.615,0.198 10 false CA1H 0.375,1.583 0.99,1.781 0.615,0.198 10 false CA1L 2.594,2.073 3,2.271 0.406,0.198 10 false D15 2.375,4.385 2.99,4.583 0.615,0.198 10 false CA4H 2.125,4.042 2.74,4.24 0.615,0.198 10 false CA4L 0.135,0.177 0.448,0.375 0.313,0.198 10 false *a 0.146,1.979 0.458,2.177 0.313,0.198 10 false *b 2.625,1.74 3.031,1.938 0.406,0.198 10 false A8 2.99,1.74 3.302,1.938 0.313,0.198 10 false *A 3,2.063 3.313,2.26 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(No. 2 EV Battery Pack Wire Connector)
*b Rear view of wire harness connector
(to EV Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,A8)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(A8)Instrument Panel>Front Compartment Main Wire>EV Control ECU

G156-4 (CA1H) - A8-2 (CA4H) Always Below 1 Ω
G156-13 (CA1L) - A8-3 (CA4L) Always Below 1 Ω
G156-4 (CA1H) or A8-2 (CA4H) - Other terminals and body ground Always 10 kΩ or higher
G156-13 (CA1L) or A8-3 (CA4L) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G156,D15)Location & Routing

Click Connector(G156)Body>Floor Wire / No. 3 Floor Wire>EV Supply Battery Assembly

Click Connector(D15)Instrument Panel>Instrument Panel Wire>EV Control ECU

G156-4 (CA1H) - D15-2 (CA4H) Always Below 1 Ω
G156-13 (CA1L) - D15-3 (CA4L) Always Below 1 Ω
G156-4 (CA1H) or D15-2 (CA4H) - Other terminals and body ground Always 10 kΩ or higher
G156-13 (CA1L) or D15-3 (CA4L) - Other terminals and body ground Always 10 kΩ or higher


NOTICE:

Make sure that each connector between the No. 2 EV battery pack wire connector and EV control ECU is not loose or disconnected and its terminals are not deformed or corroded.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G156 No. 2 EV battery pack wire connector.


b.

Install the No. 2 center floor to brace extension.


c.

Reconnect the D92 shift control ECU connector.


d.

Reconnect the A8*1 or D15*2 EV control ECU connector.

*1: for LHD

*2: for RHD



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR