Home › Engine / Hybrid System › FUEL › RECEPTACLE ASSEMBLY O-RING
RM37H0E _51 Engine / Hybrid System _097300 FUEL _0465036 RECEPTACLE ASSEMBLY O-RING A

FUEL  RECEPTACLE ASSEMBLY O-RING  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the hydrogen inlet receptacle O-ring replacement are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effects/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A477349

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·
A477350C01
1.083,1.229 1.406,0.833 1.406,0.833 1.573,0.833 false 1.604,0.75 1.854,0.927 0.25,0.177 10 true *a
*a When inside of piping is pressurized


Do not install or remove any hydrogen system components without first performing depressurization procedures.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477351C01
1.083,0.271 1.323,0.469 0.24,0.198 10 true *a
*a Manual Valve Open


Do not perform depressurization procedures when the manual valve of the hydrogen tank assembly is open.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477352

When performing depressurization, do not perform procedures by hand without wearing protective glasses and gloves.

·

The highly pressurized hydrogen gas inside the hydrogen tank assembly could blow out, resulting in a serious accident.

·
A477353C01
1.302,0.396 1.135,0.646 1.135,0.646 1.135,0.813 true 1.073,0.844 1.302,1 0.229,0.156 10 true *a
*a After depressurization procedures, the high pressure piping union nut that is loosened first.


After performing depressurization procedures, when first loosening the union nut of the high pressure hydrogen piping, do not loosen the union nut by hand without wearing protective glasses and gloves.

·

Even when depressurization procedures are performed, the pressurized hydrogen gas inside the high pressure hydrogen piping cannot be completely depressurized, so the highly pressurized hydrogen gas remaining in the high pressure hydrogen piping could blow out, resulting in a serious accident.

·
A477354

When performing the primary leak inspection, do not perform procedures without wearing protective glasses and gloves.

·

High pressure nitrogen gas could cause a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

A355341E01
0.552,8.167 6.667,8.51 6.115,0.344 10 false Place signs [HIGH PRESSURE GAS WORK IN PROGRESS - DO NOT TOUCH!], etc. to warn other technicians to be cautious. (An example sign is included, so make a copy and use it.)

·

When performing depressurization, do not open or close any parts of the hydrogen gas piping except for the following:

- Adjustment bolt of the hydrogen tank assembly manual valve

- Tank shut valve of the hydrogen tank assembly

- No. 1 hydrogen supply regulator plug

·

Even when not removing or installing the high pressure hydrogen piping, be careful not to pull or otherwise apply strain to the high pressure hydrogen piping.

·

When reusable parts such as the hydrogen tank assembly valve portion, hydrogen inlet receptacle, hydrogen tube joint and hydrogen supply regulator have been removed, to protect the seal portions and threaded portions from damage as well as to prevent foreign matter such as dust and metal fragments from entering through openings, cover these areas with protective tape.

·

Do not use packing tape, or any other tape that will leave residue on parts, as protective tape.

·
A339304C10
0.719,0.458 1.021,0.667 false 1.198,0.927 1.417,1.729 1.417,1.729 1.177,1.26 true 1.854,0.74 2,1.823 2,1.823 1.677,1.458 true 0.51,0.375 0.823,0.531 0.313,0.156 10 false *a 1.365,1.781 1.583,1.948 0.219,0.167 10 false *b 1.917,1.854 2.229,2.01 0.313,0.156 10 false *c
*a Protective Tape
*b Seal Portion
*c Threaded Portion


Protect seal portions and threaded portions as shown in the illustration.

·

To protect the seal portions and threaded portions from damage or contamination by foreign matter, remove the protective tape immediately before installation.

·

When reassembling components that have been removed, make sure that there is no foreign matter adhering to the openings.

·

When the vehicle is parked with the ignition switch off, if the FC control ECU judges that the FC stack temperature will go below 0°C (32°F), it activates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds and drains water from the FC stack assembly. When performing inspection or repairs with the ignition switch off (not on (IG) or on (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work.

·

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



Hide 58404B 2.REMOVE REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY

Hide 58403L 3.REMOVE REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY

Hide 58402K 4.REMOVE NO. 2 FLOOR BOARD SUB-ASSEMBLY

Hide 57628E 5.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 58398F 6.REMOVE NO. 1 FLOOR UNDER COVER

Hide 17DB3 7.REMOVE NO. 3 FC EXHAUST PIPE

Hide 9.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 77AE2 10.DISCONNECT HYDROGEN INLET RECEPTACLE CAP

Hide 11.REMOVE HYDROGEN INLET RECEPTACLE ASSEMBLY O RING

CAUTION:
A431708C02
1.198,0.885 1.406,0.333 1.406,0.333 1.594,0.333 true 0.948,0.854 0.781,0.313 0.781,0.313 0.604,0.313 true 0.427,0.208 0.74,0.406 0.313,0.198 10 false *a 1.615,0.24 1.927,0.438 0.313,0.198 10 false *b
*a 35 MPa (357 kgf/cm2) O-ring
*b 70 MPa (714 kgf/cm2) O-ring


Be careful not to damage the 70 MPa (714 kgf/cm2) O-ring.


HINT:

Perform this procedure when the O-ring has been damaged or remains inside the receptacle assembly.


a.

Clean the area around the fuel lid.

NOTICE:
·

Do not use solvents to clean.

·

To prevent entry of foreign matter, make sure to clean with the receptacle cap installed.




b.
A481973

Using tools made from plastic resin, remove the O-ring from the hydrogen inlet receptacle.

NOTICE:
·

When cleaning, use a clean, dry cloth.

·

Do not use compressed air or solvents to clean.

·

If an O-ring has been dropped, check it for scratches or other damage, then clean away any dust or other foreign matter before using it.

·

If foreign matter cannot be removed, use a new O-ring.

·

To avoid scratching or damaging the hydrogen inlet receptacle, use tools made from plastic resin.




Hide 12.INSTALL HYDROGEN INLET RECEPTACLE ASSEMBLY O RING

CAUTION:
A431708C02
1.198,0.885 1.406,0.333 1.406,0.333 1.594,0.333 true 0.948,0.854 0.781,0.313 0.781,0.313 0.604,0.313 true 0.427,0.208 0.74,0.406 0.313,0.198 10 false *a 1.615,0.24 1.927,0.438 0.313,0.198 10 false *b
*a 35 MPa (357 kgf/cm2) O-ring
*b 70 MPa (714 kgf/cm2) O-ring


Be careful not to damage the 70 MPa (714 kgf/cm2) O-ring.


NOTICE:
·

If an O-ring has been dropped, check it for scratches or other damage, then clean away any dust or other foreign matter before using it.

·

If foreign matter cannot be removed, use a new O-ring.



a.

Clean the area around the fuel lid.

NOTICE:
·

Do not use solvents to clean.

·

To prevent entry of foreign matter, make sure to clean with the receptacle cap installed.




b.

If the groove of the O-ring installation portion is dirty, clean it out with a piece of cloth wrapped around a tool made from plastic resin.

NOTICE:
·

When cleaning, use a piece of cloth which does not easily shed fibers.

·

Do not use compressed air or solvents to clean.

·

To avoid scratching or damaging the hydrogen inlet receptacle assembly, use tools made from plastic resin.




c.

Apply TOYOTA Genuine FC Grease to the O-ring.


d.
A481974

Install the O-ring to the hydrogen inlet receptacle assembly.


e.
A432528C01
0.219,0.156 0.531,0.354 0.313,0.198 10 false *a 0.219,2.323 0.531,2.521 0.313,0.198 10 false *b
*a Correct
*b Incorrect


Check that the O-ring is correctly seated.


Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 14. FIRST LEAK CHECK

HINT:
·

The primary leak inspection is performed when hydrogen inlet receptacle O-ring is replaced.

·

The primary leak inspection is performed using nitrogen gas.

·

When performing the primary leak inspection, remove the floor covers and rear wheel house liner so that the high pressure and medium pressure hydrogen system components and high pressure and medium pressure hydrogen system pipes are visible during inspection.



CAUTION:
A477354

·

When performing the primary leak inspection, do not perform procedures without wearing protective glasses and gloves.

·

High pressure nitrogen gas could cause a serious accident.



NOTICE:

After performing the primary leak inspection and confirming that there are no leaks, perform secondary leak inspection.


a.
A481964C02
1.74,2.813 2.042,3.135 2.042,3.135 2.208,3.135 true 1.573,1.885 1.885,2.042 0.313,0.156 10 false *a 2.25,3.052 2.563,3.208 0.313,0.156 10 false *b
*a Manual Valve Closed
*b Adjustment Bolt


Using an 8 mm socket hexagon wrench, apply the specified tightening torque to the adjustment bolt to make sure the manual valve of the No. 1 hydrogen tank assembly is closed.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 1 hydrogen tank assembly must be replaced.

·

To prevent nitrogen gas from flowing into the hydrogen tank assembly, do not open the manual valve until after the primary leak inspection is completed.




b.
A481965C02
1.74,2.813 2.042,3.135 2.042,3.135 2.208,3.135 true 1.573,1.885 1.885,2.042 0.313,0.156 10 false *a 2.25,3.052 2.563,3.208 0.313,0.156 10 false *b
*a Manual Valve Closed
*b Adjustment Bolt


Using an 8 mm socket hexagon wrench, apply the specified tightening torque to the adjustment bolt to make sure the manual valve of the No. 2 hydrogen tank assembly is closed.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 2 hydrogen tank assembly must be replaced.

·

To prevent nitrogen gas from flowing into the hydrogen tank assembly, do not open the manual valve until after the primary leak inspection is completed.




c.
A481966C02
1.74,2.813 2.042,3.135 2.042,3.135 2.208,3.135 true 1.573,1.885 1.885,2.042 0.313,0.156 10 false *a 2.25,3.052 2.563,3.208 0.313,0.156 10 false *b
*a Manual Valve Closed
*b Adjustment Bolt


Using an 8 mm socket hexagon wrench, apply the specified tightening torque to the adjustment bolt to make sure the manual valve of the No. 3 hydrogen tank assembly is closed.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion has been damaged, the No. 2 hydrogen tank assembly must be replaced.

·

To prevent nitrogen gas from flowing into the hydrogen tank assembly, do not open the manual valve until after the primary leak inspection is completed.




d.

Prepare SST (10 MPa leak inspection tool).

i.
A431713C01
2.708,1.167 2.844,0.635 2.844,0.635 2.979,0.635 false 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 3,0.531 3.229,0.698 0.229,0.167 10 false *b
*a SST (Port Assembly)
*b Vehicle-side Hose


Remove the vehicle-side hose from the cock valve portion of SST (port assembly).

SST
09402-62010  (09402-06020)


ii.
A431714C01
0.104,0.125 0.417,0.281 0.313,0.156 10 false *a
*a SST (Port Assembly)


Completely wipe away any and all adhesive remaining in the receptacle on the valve side and adhering to the connecting fittings of the hose, then blow with compressed air.

SST
09402-62010  (09402-06020)

CAUTION:
·

When performing this step, make sure that the cock valve is closed to prevent entry of foreign matter.

·

If foreign matter is allowed to enter, it could result in damage to the vehicle or device.




iii.
A431715C01
2.042,0.708 2.573,0.708 false 2.073,2.938 2.604,2.938 false 1.594,1.698 1.052,1.698 false 1.594,3.938 1.052,3.938 false 0.74,1.604 1.146,1.771 0.406,0.167 10 false SST 0.76,3.844 1.167,4.01 0.406,0.167 10 false SST 2.594,0.615 2.844,0.781 0.25,0.167 10 false *a 2.625,2.844 2.875,3.01 0.25,0.167 10 false *a
*a Seal Tape


Wrap 2-3 turns of thread seal tape around the threads of SST (10 MPa leak inspection tool), but do not cover the last 2-3 rows of threads.

SST
09402-62020  


iv.
A431713C02
2.656,1.167 2.781,0.719 2.781,0.719 2.969,0.719 false 1.115,1.115 0.854,0.5 0.854,0.5 0.656,0.5 false 0.479,0.406 0.688,0.573 0.208,0.167 10 false *a 3,0.635 3.313,0.792 0.313,0.156 10 false *b
*a SST (Port Assembly)
*b SST (10 MPa Leak Inspection Tool


Install SST (10 MPa leak inspection tool) to SST (port assembly).

SST
09402-62010  (09402-06020)
09402-62020  


v.
A339289C05
2.229,0.104 2.542,0.26 0.313,0.156 10 false *c 0.698,0.115 1.01,0.271 0.313,0.156 10 false *b 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a
*a SST (Port Assembly)
*b Discharge Valve Closed Condition
*c Injection Valve Closed Condition


Check that the injection valve and discharge valve of SST (port assembly) are closed.

SST
09402-62010  (09402-06020)


vi.
A339290C05
1.406,1.344 1.688,1.625 1.688,1.625 1.844,1.625 true 1.896,1.552 2.208,1.708 0.313,0.156 10 false *a
*a SST (Regulator Assembly)


Connect SST (regulator assembly) to a nitrogen cylinder.

SST
09402-62010  (09402-06010)

NOTICE:
·

Wrap the threaded portion with seal tape.

·

Securely tighten so that nitrogen gas will not leak out.





e.

Connect the nitrogen cylinder and SST (10 MPa (102 kgf/cm2, 1450 psi) leak inspection tool) to the hydrogen inlet receptacle.

SST
09402-62010  (09402-06010, 09402-06020)
09402-62020  

NOTICE:
·

Leave the nitrogen regulator valve closed.

·

The internal volume from the cylinder to the nozzle should be 130 cc or less.

·

The smallest marking of the pressure system should be 0.2 MPa (2.0 kgf/cm2, 29 psi) or less.



A481970C03
0.667,0.167 0.854,0.167 0.854,0.167 1.125,0.292 true 1.854,1.146 2.396,1.146 true 1.75,0.49 2.042,0.365 2.042,0.365 2.219,0.365 false 2.406,1.667 2.552,1.427 2.552,1.427 2.698,1.427 false 0.469,0.083 0.781,0.24 0.313,0.156 10 false *a 2.25,0.281 2.563,0.438 0.313,0.156 10 false *b 2.427,1.063 2.74,1.219 0.313,0.156 10 false *c 2.729,1.333 3.042,1.531 0.313,0.198 10 false *d
*a SST (Port Assembly) *b SST (Regulator Assembly)
*c Nitrogen Cylinder *d SST (10 MPa (102 kgf/cm2, 1450 psi) Leak Inspection Tool)



f.
A339292C04
3.177,0.031 3.375,0.219 0.198,0.188 10 false *a
*a Open the Nitrogen Cylinder Valve


Slowly open the nitrogen cylinder valve.


g.
A339294C07
0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.594,0.781 2.802,0.938 0.208,0.156 10 true *b
*a SST (Port Assembly)
*b Slowly Open


Slowly open the injection valve of SST (port assembly).

SST
09402-62010  (09402-06020)


h.
A339293C12
0.594,0.26 0.75,0.26 0.75,0.26 0.958,0.406 false 0.417,0.156 0.729,0.354 0.313,0.198 10 false *a 1.906,0.729 2.125,0.885 0.219,0.156 10 true *b
*a SST (Regulator Assembly)
*b Open the Nitrogen Cylinder Valve


Slowly rotate the handle of SST (regulator assembly) in the clockwise direction to open the valve, and let the pressure rise to 10 MPa (102.0 kgf/cm2, 1450 psi).

SST
09402-62010  (09402-06010)

NOTICE:
·

Raise the pressure to 10 MPa (102.0 kgf/cm2, 1450 psi) over a period of 5 to 20 seconds.

·

If there is a hissing sound of nitrogen gas leaking out when the SST (regulator assembly) valve is opened, close the SST (regulator assembly) valve, and after determining the location of the leak, replace the leaking component with a new one.

·

Even when it seems like the leaking sound is only coming from one location, it may be drowning out leaking sounds from other locations, so make sure to perform leakage point identification for all connecting portions.




i.
A479216C02
2.031,1.542 1.417,1.542 false 1.542,0.49 2.229,0.229 2.229,0.229 2.406,0.229 true 2.448,0.156 2.76,0.313 0.313,0.156 10 false *1 1.208,1.458 1.521,1.615 0.313,0.156 10 false *a
*1 Auxiliary Battery
*a Battery Charger


Connect a battery charger to the auxiliary battery, and put the auxiliary battery into a charging state.

HINT:

This is done to prevent the auxiliary battery from becoming discharged, as the tank shut valve of the hydrogen tank assembly will be forced to operate for 30 minutes.



j.

Using the GTS, enter the following menus: Body Electrical / Power Source Control / Utility / Auto Power OFF Cancel

Body Electrical > Power Source Control > Utility
Tester Display
Auto Power OFF Cancel
50005 223 5148

k.

Open the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly.

NOTICE:
·

If the Data List item "Medium-range Hydrogen Pressure (gauge)" decreases to below 0.7 kPa (7.1 kgf/cm2, 102 psi) the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly will forcibly close.

·

If there is a hissing sound of nitrogen gas leaking out when the tank shut valves are opened, close both tank shut valves, and after determining the location of the leak, replace the leaking component with a new one.

·

Even when it seems like the leaking sound is only coming from one location, it may be drowning out leaking sounds from other locations, so make sure to perform leakage point identification for all connecting portions.




l.

If the tank shut valves of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly do not open, open the tank shut valves again.


m.

When the tank shut valve has been opened, if the pressure has gone below 10 MPa (102.0 kgf/cm2, 1450 psi), increase the pressure to 10 MPa (102.0 kgf/cm2, 1450 psi).


n.
A481971C02
2.667,0.865 2.979,1.021 0.313,0.156 10 false *a
*a Close the Nitrogen Cylinder Valve


Close the nitrogen cylinder valve.


o.
A481972C02
1.073,0.406 0.781,0.302 0.781,0.302 0.563,0.302 false 0.542,1.344 0.771,1.5 0.229,0.156 10 false *b 0.385,0.208 0.615,0.365 0.229,0.156 10 false *a
*a SST (Regulator Assembly)
*b Close the SST (Regulator Assembly) Valve


Rotate the handle of SST (regulator assembly) in the counterclockwise direction to close the valve.

SST
09402-62010  (09402-06010)


p.

After closing the nitrogen cylinder valve and the SST (regulator assembly) valve, wait for 10 minutes to allow the pressure in the piping to stabilize.

HINT:

When nitrogen has just been filled, the temperature inside the piping is increased, causing pressure to increase. Afterwards, when the temperature in the piping decreases, the pressure decreases. For this reason, pressure is not stable immediately after nitrogen filling.



q.
A339297

After checking that the pressure gauge has stabilized, wait an additional 30 minutes, and then check the pressure gauge.

OK:

Pressure decrease is 0.2 MPa (2.0 kgf/cm2, 29 psi) or less


·

When the pressure decrease is 0.2 MPa (2.0 kgf/cm2, 29 psi) or less:

Go to "When pressure decrease is 0.2 MPa (2.0 kgf/cm2, 29 psi) or less"

·

When the pressure decrease is more than 0.2 MPa (2.0 kgf/cm2, 29 psi):

Go to "When pressure decrease is more than 0.2 MPa (2.0 kgf/cm2, 29 psi)



r.

When pressure decrease is 0.2 MPa (2.0 kgf/cm2, 29 psi) or less:

i.
A346287C08
0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.635,0.76 1.823,0.948 0.188,0.188 10 true *b
*a SST (Port Assembly)
*b Open the Discharge Valve of SST (Port Assembly)


Slowly open the discharge valve of SST (port assembly) to depressurize the nitrogen gas.

SST
09402-62010  (09402-06020)

NOTICE:

Keep your hands and face away from the discharge port.



ii.
A339293C13
0.531,0.281 0.688,0.281 0.688,0.281 0.917,0.469 false 0.354,0.188 0.667,0.385 0.313,0.198 10 false *a 1.906,0.708 2.104,0.885 0.198,0.177 10 true *b
*a SST (Regulator Assembly)
*b Open the SST (Regulator Assembly) Valve


Slowly rotate the handle of SST (regulator assembly) a small amount in the clockwise direction to open the valve.

SST
09402-62010  (09402-06010)

HINT:

This is done to reduce the pressure of the nitrogen gas between the nitrogen cylinder and SST (regulator assembly).



iii.
A343972C08
0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 2.635,0.198 2.948,0.396 0.313,0.198 10 false *b
*a SST (Port Assembly)
*b Close the Injection Valve of SST (Port Assembly)


Close the injection valve of SST (port assembly).

SST
09402-62010  (09402-06020)


iv.
A343973C08
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.302,0.292 1.615,0.49 0.313,0.198 10 false *b
*a SST (Port Assembly)
*b Close the Discharge Valve of SST (Port Assembly)


Close the discharge valve of SST (port assembly).

SST
09402-62010  (09402-06020)


v.
A479198

Slowly loosen the No. 1 hydrogen supply regulator plug until the hissing sound of gas escaping can be heard, then stop loosening the No. 1 hydrogen supply regulator plug and wait for the sound to stop. Repeat this procedure multiple times until the sound stops occurring, in order to depressurize the nitrogen gas from the medium pressure leak check port of the hydrogen supply regulator.

NOTICE:

When depressurizing the nitrogen gas, only loosen the No. 1 hydrogen supply regulator plug. Do not remove it.



vi.
A479199

Remove the No. 1 hydrogen supply regulator plug from the hydrogen supply regulator.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



vii.
A479200

Remove the O-ring from the hydrogen supply regulator.


viii.
A479201C02
1.781,0.917 2.417,0.917 true 2.417,0.833 2.635,1.031 0.219,0.198 10 true *a
*a Protective Tape


To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, cover the seal portions, threaded portions, and openings of the hydrogen supply regulator with protective tape.


ix.
A479202

To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, do not remove the protective tape covering the seal portions, threaded portions, and openings of the hydrogen supply regulator until immediately before performing work.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



x.
A479203

Apply TOYOTA Genuine FC Grease to a new O-ring and to the threaded portion of the hydrogen supply regulator.


xi.
A479204

Install the O-ring to the hydrogen supply regulator.

NOTICE:

During installation, make sure not to damage the O-ring.



xii.
A479221C02
2.115,0.49 2.354,0.229 2.354,0.229 2.5,0.229 true 2.51,0.906 2.74,1.073 0.229,0.167 10 true *a 2.542,0.146 2.875,0.313 0.333,0.167 10 true SST
*a Torque Wrench Fulcrum Length


Using SST install the No. 1 hydrogen supply regulator plug to the hydrogen supply regulator.

SST
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)




xiii.

Close the tank shut valve of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly.


xiv.

Disconnect the nitrogen cylinder and SST (10 MPa (102 kgf/cm2, 1450 psi) leak inspection tool) from the hydrogen inlet receptacle.

SST
09402-62010  (09402-06010, 09402-06020)
09402-62020  

A481970C03
0.667,0.167 0.854,0.167 0.854,0.167 1.125,0.292 true 1.854,1.146 2.396,1.146 true 1.75,0.49 2.042,0.365 2.042,0.365 2.219,0.365 false 2.406,1.667 2.552,1.427 2.552,1.427 2.698,1.427 false 0.469,0.083 0.781,0.24 0.313,0.156 10 false *a 2.25,0.281 2.563,0.438 0.313,0.156 10 false *b 2.427,1.063 2.74,1.219 0.313,0.156 10 false *c 2.729,1.333 3.042,1.531 0.313,0.198 10 false *d
*a SST (Port Assembly) *b SST (Regulator Assembly)
*c Nitrogen Cylinder *d SST (10 MPa (102 kgf/cm2, 1450 psi) Leak Inspection Tool)



xv.
A479213C02
2.667,3.115 2.667,2.865 true 1.49,2.938 1.302,2.938 1.302,2.938 1.021,2.813 true 1.51,2.854 1.823,3.01 0.313,0.156 10 false *c 0.865,1.969 1.177,2.125 0.313,0.156 10 false *a 2.542,1.958 2.854,2.115 0.313,0.156 10 false *b 1.292,3.094 1.604,3.25 0.313,0.156 10 false *d 2.615,3.125 2.927,3.281 0.313,0.156 10 false *c
*a Manual Valve Closed
*b Manual Valve Open
*c Adjustment Bolt
*d Counterclockwise


Using an 8 mm socket hexagon wrench, rotate the adjustment bolt counterclockwise, and open the No. 1 hydrogen tank assembly manual valve.

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion is damaged, it will be impossible to operate the adjustment bolt.

·

Do not rotate the adjustment bolt more than 4 rotations.

·

Rotating the adjustment bolt more than 4 rotations could damage the manual valve.

·

If the manual valve is damaged, it will be necessary to replace the No. 1 hydrogen tank assembly.

·

Before opening the manual valve, check that the nitrogen gas contained in the hydrogen piping has been depressurized.



HINT:
A479226C02
0.917,1.625 1.094,1.625 1.094,1.625 1.448,1.385 false 0.719,1.531 1.031,1.688 0.313,0.156 10 false *a 3.021,1.271 3.25,1.427 0.229,0.156 10 false *b
*a Adjustment Bolt
*b Protrusion


When the manual valve is opened, the protrusion of the adjustment bolt is 3.5 mm (0.138 in.) or less.



xvi.
A479214C02
2.667,3.115 2.667,2.865 true 1.49,2.938 1.302,2.938 1.302,2.938 1.021,2.813 true 1.51,2.854 1.823,3.01 0.313,0.156 10 false *c 0.865,1.969 1.177,2.125 0.313,0.156 10 false *a 2.542,1.958 2.854,2.115 0.313,0.156 10 false *b 1.292,3.094 1.604,3.25 0.313,0.156 10 false *d 2.615,3.125 2.927,3.281 0.313,0.156 10 false *c
*a Manual Valve Closed
*b Manual Valve Open
*c Adjustment Bolt
*d Counterclockwise


Using an 8 mm socket hexagon wrench, rotate the adjustment bolt counterclockwise, and open the No. 2 hydrogen tank assembly manual valve.

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion is damaged, it will be impossible to operate the adjustment bolt.

·

Do not rotate the adjustment bolt more than 4 rotations.

·

Rotating the adjustment bolt more than 4 rotations could damage the manual valve.

·

If the manual valve is damaged, it will be necessary to replace the No. 2 hydrogen tank assembly.



HINT:
A479226C02
0.917,1.625 1.094,1.625 1.094,1.625 1.448,1.385 false 0.719,1.531 1.031,1.688 0.313,0.156 10 false *a 3.021,1.271 3.25,1.427 0.229,0.156 10 false *b
*a Adjustment Bolt
*b Protrusion


When the manual valve is opened, the protrusion of the adjustment bolt is 3.5 mm (0.138 in.) or less.



xvii.
A479215C02
2.667,3.115 2.667,2.865 true 1.49,2.938 1.302,2.938 1.302,2.938 1.021,2.813 true 1.51,2.854 1.823,3.01 0.313,0.156 10 false *c 0.865,1.969 1.177,2.125 0.313,0.156 10 false *a 2.542,1.958 2.854,2.115 0.313,0.156 10 false *b 1.292,3.094 1.604,3.25 0.313,0.156 10 false *d 2.615,3.125 2.927,3.281 0.313,0.156 10 false *c
*a Manual Valve Closed
*b Manual Valve Open
*c Adjustment Bolt
*d Counterclockwise


Using an 8 mm socket hexagon wrench, rotate the adjustment bolt counterclockwise, and open the No. 3 hydrogen tank assembly manual valve.

NOTICE:
·

The manual valve shuts off the pressure from the hydrogen tank assembly, so be careful not to damage the hexagonal portion.

·

If the hexagonal portion is damaged, it will be impossible to operate the adjustment bolt.

·

Do not rotate the adjustment bolt more than 4 rotations.

·

Rotating the adjustment bolt more than 4 rotations could damage the manual valve.

·

If the manual valve is damaged, it will be necessary to replace the No. 3 hydrogen tank assembly.



HINT:
A479226C02
0.917,1.625 1.094,1.625 1.094,1.625 1.448,1.385 false 0.719,1.531 1.031,1.688 0.313,0.156 10 false *a 3.021,1.271 3.25,1.427 0.229,0.156 10 false *b
*a Adjustment Bolt
*b Protrusion


When the manual valve is opened, the protrusion of the adjustment bolt is 3.5 mm (0.138 in.) or less.



xviii.

After performing primary leak inspection and confirming that there are no leaks, check that compressed hydrogen gas can be filled without any problem at a hydrogen station.



s.

When pressure decrease is more than 0.2 MPa (2.0 kgf/cm2, 29 psi):

i.

Using soapy water, check the connection points to determine the locations of the leaks.

HINT:

If the soapy water on the part connection points is difficult to see, use a mirror and a light.


A482159C03
0.115,0.146 0.427,0.302 0.313,0.156 10 false *a
*a FC Stack-side Leak Check Locations - -


A481968C08
0.156,0.188 0.469,0.344 0.313,0.156 10 false *a
*a Hydrogen Tank-side Leak Check Locations - -


A481969C02
0.167,0.156 0.479,0.313 0.313,0.156 10 false *a
*a Nitrogen Regulator-side Leak Check Locations - -



ii.
A346287C08
0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.635,0.76 1.823,0.948 0.188,0.188 10 true *b
*a SST (Port Assembly)
*b Open the Discharge Valve of SST (Port Assembly)


Slowly open the discharge valve of SST (port assembly) to depressurize the nitrogen gas.

SST
09402-62010  (09402-06020)

NOTICE:

Keep your hands and face away from the discharge port.



iii.
A339293C13
0.531,0.281 0.688,0.281 0.688,0.281 0.917,0.469 false 0.354,0.188 0.667,0.385 0.313,0.198 10 false *a 1.906,0.708 2.104,0.885 0.198,0.177 10 true *b
*a SST (Regulator Assembly)
*b Open the SST (Regulator Assembly) Valve


Slowly rotate the handle of SST (regulator assembly) a small amount in the clockwise direction to open the valve.

SST
09402-62010  (09402-06010)

HINT:

This is done to reduce the pressure of the nitrogen gas between the nitrogen cylinder and SST (regulator assembly).



iv.
A343972C08
0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 2.635,0.198 2.948,0.396 0.313,0.198 10 false *b
*a SST (Port Assembly)
*b Close the Injection Valve of SST (Port Assembly)


Close the injection valve of SST (port assembly).

SST
09402-62010  (09402-06020)


v.
A343973C08
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.302,0.292 1.615,0.49 0.313,0.198 10 false *b
*a SST (Port Assembly)
*b Close the Discharge Valve of SST (Port Assembly)


Close the discharge valve of SST (port assembly).

SST
09402-62010  (09402-06020)


vi.
A479198

Slowly loosen the No. 1 hydrogen supply regulator plug until the hissing sound of gas escaping can be heard, then stop loosening the No. 1 hydrogen supply regulator plug and wait for the sound to stop. Repeat this procedure multiple times until the sound stops occurring, in order to depressurize the nitrogen gas from the medium pressure leak check port of the hydrogen supply regulator.

NOTICE:

When depressurizing the nitrogen gas, only loosen the No. 1 hydrogen supply regulator plug. Do not remove it.



vii.
A479199

Remove the No. 1 hydrogen supply regulator plug from the hydrogen supply regulator.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



viii.
A479200

Remove the O-ring from the hydrogen supply regulator.


ix.
A479201C02
1.781,0.917 2.417,0.917 true 2.417,0.833 2.635,1.031 0.219,0.198 10 true *a
*a Protective Tape


To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, cover the seal portions, threaded portions, and openings of the hydrogen supply regulator with protective tape.


x.
A479202

To prevent damage to the seal portions and threaded portions, and to prevent foreign matter such as dust or metal fragments from entering the openings, do not remove the protective tape covering the seal portions, threaded portions, and openings of the hydrogen supply regulator until immediately before performing work.

NOTICE:

When frost has formed on the hydrogen tank assembly or piping, water droplets may be formed when the frost begins to melt. If water droplets enter the tank or piping, it could result in blockage of the hydrogen piping, so do not allow water droplets to enter the tank or piping.



xi.
A479203

Apply TOYOTA Genuine FC Grease to a new O-ring and to the threaded portion of the hydrogen supply regulator.


xii.
A479204

Install the O-ring to the hydrogen supply regulator.

NOTICE:

During installation, make sure not to damage the O-ring.



xiii.
A479221C02
2.115,0.49 2.354,0.229 2.354,0.229 2.5,0.229 true 2.51,0.906 2.74,1.073 0.229,0.167 10 true *a 2.542,0.146 2.875,0.313 0.333,0.167 10 true SST
*a Torque Wrench Fulcrum Length


Using SST install the No. 1 hydrogen supply regulator plug to the hydrogen supply regulator.

SST
09922-10240  

Torque:
Specified tightening torque:

9.0 N*m (92 kgf*cm, 80 in.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 40 mm (1.57 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 7.2 N*m (73 kgf*cm, 64 in.*lbf)




xiv.

Close the tank shut valve of the No. 1 hydrogen tank assembly, No. 2 hydrogen tank assembly and No. 3 hydrogen tank assembly.


xv.

Disconnect the nitrogen cylinder and SST (10 MPa (102 kgf/cm2, 1450 psi) leak inspection tool) from the hydrogen inlet receptacle.

SST
09402-62010  (09402-06010, 09402-06020)
09402-62020  

A481970C03
0.667,0.167 0.854,0.167 0.854,0.167 1.125,0.292 true 1.854,1.146 2.396,1.146 true 1.75,0.49 2.042,0.365 2.042,0.365 2.219,0.365 false 2.406,1.667 2.552,1.427 2.552,1.427 2.698,1.427 false 0.469,0.083 0.781,0.24 0.313,0.156 10 false *a 2.25,0.281 2.563,0.438 0.313,0.156 10 false *b 2.427,1.063 2.74,1.219 0.313,0.156 10 false *c 2.729,1.333 3.042,1.531 0.313,0.198 10 false *d
*a SST (Port Assembly) *b SST (Regulator Assembly)
*c Nitrogen Cylinder *d SST (10 MPa (102 kgf/cm2, 1450 psi) Leak Inspection Tool)



xvi.

After replacing the leaking component with a new one, perform primary leak inspection again.


xvii.

If there is a leak, check the O-ring for scratches or other damage.


xviii.

If the O-ring is scratched or damaged, replace it with a new one and perform leak inspection again.


xix.

If there is still a leak after replacing the O-ring, replace the hydrogen inlet receptacle assembly with a new one and perform leak inspection again.



Hide 17DB3 15.INSTALL NO. 3 FC EXHAUST PIPE

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 58398F 18.INSTALL NO. 1 FLOOR UNDER COVER

Hide 57628E 19.INSTALL REAR FLOOR SIDE MEMBER COVER LH

Hide 58402K 20.INSTALL NO. 2 FLOOR BOARD SUB-ASSEMBLY

Hide 58403L 21.INSTALL REAR NO. 3 FLOOR BOARD SUB-ASSEMBLY

Hide 58404B 22.INSTALL REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY

Hide 77AE2 23.CONNECT HYDROGEN INLET RECEPTACLE CAP