Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1D3F16  FC Stack Internal Voltage Circuit Voltage Below Threshold  


DESCRIPTION

During FC power generation, the FC stack generates a voltage of 220 to 330 V and feeds it into the FC converter assembly through the stack positive and negative circuits. (The stack voltage gradually decreases as the FC system stops)

If a voltage, which is normally 220 to 330 V, between the stack positive and negative circuits decreases abnormally, due to overcurrent caused by short-circuited terminals, the EV control ECU interprets it as a malfunction and store this DTC.

A479009E02
6.271,0.125 7.125,0.948 0.854,0.823 10 false Each cell is measured (1cell) 6.219,3.75 7.073,4.573 0.854,0.823 10 false Each cell is measured (1cell) 6.26,1.948 7.073,2.729 0.813,0.781 10 false 2 cells are measured (328 cells in total) 5.281,4.438 6.51,4.635 1.229,0.198 10 false FC Stack 3.771,4.229 5.271,5.115 1.5,0.885 10 false FC Stack Voltage Sensor (Cell Monitor) 2.438,4.229 3.49,4.823 1.052,0.594 10 false FC Boost Control ECU 2.146,5.292 3.667,5.75 1.521,0.458 10 false FC Converter Assembly 4.167,5.323 5.844,5.688 1.677,0.365 10 false FC Stack Assembly 3.969,0.531 4.74,0.729 0.771,0.198 10 false CMPWC 3.969,3.615 4.583,3.813 0.615,0.198 10 false CMGO 3.979,1.948 4.594,2.146 0.615,0.198 10 false DCCH 2.948,1.917 3.563,2.115 0.615,0.198 10 false DCCH 3.958,2.333 4.573,2.531 0.615,0.198 10 false DCCL 2.979,2.323 3.594,2.521 0.615,0.198 10 false DCCL 2.896,3.604 3.51,3.802 0.615,0.198 10 false CMGO 2.792,0.552 3.563,0.75 0.771,0.198 10 false CMPWC 2.438,1.875 3.052,2.073 0.615,0.198 10 false CA1H 2.438,2.323 3.052,2.521 0.615,0.198 10 false CA1L 1.542,1.906 2.156,2.104 0.615,0.198 10 false CA1H 1.552,2.281 2.167,2.479 0.615,0.198 10 false CA1L 2.427,0.969 2.885,1.167 0.458,0.198 10 false +B2 2.417,0.51 2.875,0.708 0.458,0.198 10 false +B1 2.417,3.615 2.729,3.813 0.313,0.198 10 false E2 2.417,3.25 2.729,3.448 0.313,0.198 10 false E1 1.042,2.833 3.188,3.031 2.146,0.198 10 false EV Control ECU 1.198,1.583 1.813,1.781 0.615,0.198 10 false MREL 0.583,1.167 1.448,1.375 0.865,0.208 10 false IGCT NO. 1 0.313,1.813 1.177,2.021 0.865,0.208 10 false IGCT NO. 1 0.323,2.458 1.188,2.667 0.865,0.208 10 false R/R RR# 2 1.458,0.635 1.948,1.177 0.49,0.542 10 false IGCT NO. 7 0.51,3.198 3.115,3.396 2.604,0.198 10 false Auxiliary Battery

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1D3F16 FC Stack Internal Voltage Circuit Voltage Below Threshold If the FC stack total voltage (sum of each cell voltage measured by the cell monitor) has decreased below a specified voltage.
This malfunction detection is activated when the amount of supplied air and hydrogen is sufficient during power generation of the FC stack ("FC Work Mode" is in FC Working).
(1 trip detection logic)
·

FC stack assembly

·

Cell monitor (FC stack voltage sensor)

·

No. 3 FC converter wire

·

Fuell cell stack monitor wire

·

Exhaust Drainage Valve

·

Mass air flow meter sub-assembly

·

Hydrogen secondary pressure sensor (low-range hydrogen pressure sensor)

·

FC air pressure regulator assembly (air pressure regulating valve)

·

FC air by-pass valve assembly (air shunt valve)

·

FC air pressure regulator assembly (air sealing valve)


Master Warning: Comes on EV B

HINT:

If there is a short circuit in the FC stack output (trigger for this DTC), the FC system cannot be actuated. If actuation is allowed, the malfunction has not been reproduced.


Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - - ○ ○ ○ -

HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1D3F16
·

Total Voltage

·

FC Voltage (Filtered Value)



CAUTION / NOTICE / HINT

NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift state in park (P), the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).


After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF.

2.

Check that the "Total Voltage" value of the Data List is more than 200 V (except for a situation where an ambient temperature is below 0°C (32°F) or intermittent operation is active).



PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1D3F16 is output A
P1D3F16 is output and DTCs other than the DTCs in the table below are output B
P1D3F16 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1D8396 (EV) Hydrogen Pump Inverter Component Internal Failure
P1DCF96 (EV) Cell Monitor Component Internal Failure
Communication system malfunction P1D8387 (EV) Lost Communication with Hydrogen Pump Inverter Missing Message
System malfunction P1D2496 (EV) Hydrogen Pump Component Internal Failure
P1D7F62 (EV) FC Air Compressor Motor Signal Compare Failure
P1D7F96 (EV) FC Air Compressor Motor Component Internal Failure
P1DC000 (EV) Low-Range Hydrogen Pressure Too Low
P1DC500 (EV) FC Air Pressure Too High
P1DDF00 (EV) FC Air Flow Malfunction
P1DDF79 (EV) FC Air Flow Mechanical Linkage Failure
P1E427A (EV) Hydrogen Leak (Excessive Hydrogen Flow) Fluid Leak or Seal Failure
P1E4862 (EV) FC Stack Inlet Pressure Sensor/Barometric Pressure Sensor "B" Signal Compare Failure
P1F6C71 (EV) Air Sealing Valve Actuator Stuck
P1F6D71 (EV) Air Shunt Valve Actuator Stuck
P1F6E71 (EV) Air Pressure Regulating Valve Actuator Stuck


HINT:

DTC P1D3F16 may be store due to problems that cause the DTCs shown above to output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA

C

GO TO DTC CHART

2.CHECK FREEZE FRAME DATA
NOTICE:

The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

Read the freeze frame data of DTC P1D3F16.

Powertrain > EV > DTC(P1D3F16) > Freeze Frame Data
Tester Display
Total Voltage
FC Voltage (Filtered Value)
50040 397 929,923 P1D3F16
Result:
Result Proceed to
Other than below A
Voltage difference between "Total Voltage" and "FC Voltage (Filtered Value)" is more than 50 V* B


*: The cell monitor (FC stack voltage sensor) is malfunctioning



Post-procedure1

a.

Turn the ignition switch off.



A

3.CLEAR DTC

B

REPLACE FC CONVERTER AND FC STACK ASSEMBLY COMPONENT PARTS

Replace the FC converter and FC stack assembly components listed below.

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL

·

Cell monitor (FC stack voltage sensor)

·

No. 3 FC converter wire

·

Fuell cell stack monitor wire


HINT:
·

Refer to the parts location for the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>PARTS LOCATION

·

Refer to the system description for the parts location of the FC converter and FC stack assembly components.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>SYSTEM DESCRIPTION




3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

4.READ VALUE USING GTS (TOTAL VOLTAGE, FC WORK MODE, FC INTERMITTENT OPERATION)
4.READ VALUE USING GTS (TOTAL VOLTAGE, FC WORK MODE, FC INTERMITTENT OPERATION)

Pre-procedure1

a.

None


Procedure1

a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF.

Powertrain > EV > Data List
Tester Display
Total Voltage
FC Work Mode
FC Intermittent Operation
50003 397 929,962,872

b.

Read the "Total Voltage" of the Data List.

Result:
Result Proceed to
FC system can be actuated A
FC system cannot be actuated, and "Total Voltage" is less than 200 V B



Post-procedure1

a.

None



A

5.SIMULATION TEST

B

5.SIMULATION TEST

Pre-procedure1

a.

Drive the vehicle for 10 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.)

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.


HINT:

If vehicle speeds, accelerator pedal positions, road conditions, ambient temperatures and climates at the time the malfunction occurred can be found out, take them into account.



Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1D3F16 is output B



Post-procedure1

a.

Turn the ignition switch off.



A

B

6.CHECK EXHAUST HYDROGEN GAS
6.CHECK EXHAUST HYDROGEN GAS
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



Pre-procedure1

a.

Ensure the safety of the areas in front and at the back of the vehicle.


b.

Put wheel chocks and securely apply the parking brake.


Procedure1

a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working, "FC Intermittent Operation" is OFF, and "Exhaust Drainage Valve" is Close.

Powertrain > EV > Active Test
Active Test Display
Activate the Exhaust Drainage Valve
Data List Display
FC Work Mode
FC Intermittent Operation
Exhaust Drainage Valve
50004 397 42006 962,872,818

b.
A476956C02
0.875,2.563 1.833,1.885 true 2.042,2.042 2.75,1.583 2.75,1.583 2.938,1.573 true 0.604,2.563 0.917,2.76 0.313,0.198 10 true *1 3,1.49 3.313,1.688 0.313,0.198 10 true *2
*1 Tailpipe
*2 Hydrogen Gas Detector Probe


Use the hydrogen gas detector to measure and record the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is closed.

NOTICE:
·

Perform this measurement in an environment where there is no wind.

·

Position the hydrogen gas detector probe in an area 100 mm (3.94 in.) away from the tailpipe opening. (Avoid locations underneath the tailpipe opening)

·

Position the hydrogen gas detector probe so that it is free from dropping water that comes from the tailpipe opening.




c.

Perform the "Activate the Exhaust Drainage Valve" Active Test several times over 1 minute, and then, starting from the third test, use the hydrogen gas detector to measure the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is open.

HINT:
·

The exhaust drainage valve will open for 1 second each time the Active Test is performed, so measure the hydrogen concentration for several seconds.

·

Hydrogen concentration may not increase while coolant escapes when the valve is first opened. Therefore, start measuring from the third test.

·

There is a delayed response when performing detection using the hydrogen gas detector, so measure for several seconds.

·

"FC Intermittent Operation" in the Data List will be more likely to turn OFF if the accelerator pedal is depressed with the shift state in park (P).




Result:
Result Proceed to
The hydrogen concentration of the hydrogen gas detector will increase when "Exhaust Drainage Valve" in the Data List is Open rather than when "Exhaust Drainage Valve" is Close. A
Other than above* B


*: The exhaust drainage valve is malfunctioning

Exhaust drainage valve is stuck closed:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained low.


Exhaust drainage valve is stuck open:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained high when the ignition switch is on (READY).



Post-procedure1

a.

Turn the ignition switch off.



A

7.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))

B

REPLACE HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

7.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Mass Air Flow (Filtered Value)
50003 397 897
Result:
Result Proceed to
The value of Mass Air Flow (Filtered Value) is less than 8 L/min A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

8.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

8.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Remove the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor).

HINT:

Click hereEngine / Hybrid System>FC CONTROL>HYDROGEN PRESSURE SENSOR>REMOVAL



b.

Reconnect the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor) connector.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Low-Range Hydrogen Pressure (Filtered Value)
50003 397 1032

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




c.

Compare the "Low-Range Hydrogen Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "Low-Range Hydrogen Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 35 kPa or more. A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN SECONDARY PRESSURE SENSOR

B

9.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)
9.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air sealing valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air sealing valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air sealing valve).



OK

10.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

10.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air pressure regulating valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air pressure regulating valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air pressure regulating valve).



OK

11.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

11.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

Pre-procedure1

a.

Remove the FC air by-pass valve assembly (air shunt valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR BYPASS VALVE>REMOVAL



Procedure1

a.

Visually check the FC air by-pass valve assembly (air shunt valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air by-pass valve assembly (air shunt valve).



OK

REPLACE FC STACK ASSEMBLY

NG

REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)