Home › Engine / Hybrid System › FC CONTROL › FC CONTROL SYSTEM
RM37H0E _51 Engine / Hybrid System _095966 FC CONTROL _0466766 FC CONTROL SYSTEM C

FC CONTROL  FC CONTROL SYSTEM  P1DEF00  FC System No Activation  


DESCRIPTION

The FC stack consists of 330 cells. The amounts of hydrogen and air that are fed into the FC stack, and the FC stack temperature are regulated for stable power generation.

If the cell voltage, which is based on each cell voltage watched by the cell monitor, is abnormally low despite that both hydrogen and air are supplied more than the specified amounts and the cooling system is operating properly, the EV control ECU interprets it as a FC stack malfunction, and stores this DTC.

A477023C03
0.094,1.354 0.25,0.313 false 6.896,2.792 7.135,2.979 0.24,0.188 10 false *1 6.875,1.458 7.125,1.688 0.25,0.229 10 false *2 6.479,5.344 6.792,5.5 0.313,0.156 10 false *3 5.646,5.344 5.958,5.5 0.313,0.156 10 false *4 6.51,4.75 6.823,4.906 0.313,0.156 10 false *6 5.604,4.771 5.917,4.927 0.313,0.156 10 false *7 4.76,4.76 5.073,4.917 0.313,0.156 10 false *8 6.458,3.635 6.771,3.792 0.313,0.156 10 false *9 5.563,3.646 6.031,3.802 0.469,0.156 10 false *10 4.729,3.646 5.198,3.802 0.469,0.156 10 false *11 5.521,1.646 5.99,1.802 0.469,0.156 10 false *12 5.125,0.542 5.594,0.698 0.469,0.156 10 false *13 4.719,0.5 5.188,0.656 0.469,0.156 10 false *14 4.323,1.188 4.792,1.344 0.469,0.156 10 false *15 3.823,0.542 4.292,0.698 0.469,0.156 10 false *16 3.958,1.604 4.427,1.76 0.469,0.156 10 false *17 3.583,2.573 4.052,2.729 0.469,0.156 10 false *18 3.021,1.583 3.49,1.74 0.469,0.156 10 false *19 0.573,6.083 1.042,6.24 0.469,0.156 10 false *20 0.448,5.438 0.917,5.594 0.469,0.156 10 false *21 0.708,5.438 1.177,5.594 0.469,0.156 10 false *22 1.458,6.208 1.927,6.365 0.469,0.156 10 false *23 1.458,5.854 1.927,6.01 0.469,0.156 10 false *24 1.917,6.042 2.385,6.198 0.469,0.156 10 false *25 2.24,6.167 2.708,6.323 0.469,0.156 10 false *26 2.531,6.167 3,6.323 0.469,0.156 10 false *27 0.438,0.927 0.906,1.083 0.469,0.156 10 false *28 2.552,3.198 2.813,3.448 0.26,0.25 10 false *46 0.354,0.438 0.823,0.594 0.469,0.156 10 false *30 1.646,0.542 2.115,0.698 0.469,0.156 10 false *31 2.427,2.208 2.896,2.365 0.469,0.156 10 false *32 1.385,2.646 1.854,2.802 0.469,0.156 10 false *33 1.625,1.594 2.094,1.75 0.469,0.156 10 false *34 4.708,3.99 5.177,4.146 0.469,0.156 10 false *35 0.26,6.104 0.729,6.26 0.469,0.156 10 false *36 3.958,0.958 4.427,1.115 0.469,0.156 10 false *37 4.74,4.167 5.208,4.323 0.469,0.156 10 false *38 6.635,5.573 6.948,5.729 0.313,0.156 10 false *a 6.635,5.885 6.948,6.042 0.313,0.156 10 false *b 6.615,6.208 6.927,6.365 0.313,0.156 10 false *c 5.25,5.844 5.563,6 0.313,0.156 10 false *e 2.542,3.729 3.01,3.885 0.469,0.156 10 false *47 5.604,4.167 6.073,4.323 0.469,0.156 10 false *38 6.458,4.177 6.927,4.333 0.469,0.156 10 false *38 5.583,3.979 6.052,4.135 0.469,0.156 10 false *35 6.448,3.979 6.917,4.135 0.469,0.156 10 false *35 4.781,5.323 5.094,5.479 0.313,0.156 10 false *5 0.208,0.167 0.677,0.323 0.469,0.156 10 false *29 2.896,3.094 3.365,3.25 0.469,0.156 10 false *39 3.531,3.094 4,3.25 0.469,0.156 10 false *40 3.021,3.948 3.49,4.104 0.469,0.156 10 false *41 0.448,4.844 0.917,5 0.469,0.156 10 false *42 6.615,6.521 6.927,6.677 0.313,0.156 10 false *d 0.198,3.708 0.448,4.063 0.25,0.354 10 false *43 0.438,3.708 0.688,4.063 0.25,0.354 10 false *44 0.958,3.719 1.208,4.073 0.25,0.354 10 false *45 4.26,4.917 4.729,5.073 0.469,0.156 10 false *48 3.802,5.469 4.271,5.625 0.469,0.156 10 false *49
*1 Hydrogen Inlet Receptacle Assembly *2 Hydrogen Tank Pressure Sensor (for Inlet Side)
*3 No. 1 Hydrogen Tank Assembly *4 No. 2 Hydrogen Tank Assembly
*5 No. 3 Hydrogen Tank Assembly *6 Hydrogen Tank Temperature Sensor 1
*7 Hydrogen Tank Temperature Sensor 2 *8 Hydrogen Tank Temperature Sensor 3
*9 Tank Shut Valve 1 *10 Tank Shut Valve 2
*11 Tank Shut Valve 3 *12 Hydrogen Tank Pressure Sensor (for Outlet Side)
*13 Hydrogen Supply Regulator Assembly *14 Hydrogen Primary Pressure Sensor
*15 Fuel Injector Assembly *16 Hydrogen Secondary Pressure Sensor
*17 Hydrogen Recirculation Pump Assembly *18 Exhaust Drainage Valve (Hydrogen Recirculation Separator Assembly)
*19 FC Stack Assembly *20 Mass Air Flow Meter Sub-assembly
*21 Airflow Sensor *22 Intake Air Temperature Sensor
*23 FC Air Compressor with Motor Assembly *24 FC Air Compressor
*25 Intercooler *26 FC Stack Inlet Air Temperature Sensor (Vacuum Sensor Assembly)
*27 FC Stack Inlet Air Pressure Sensor (Vacuum Sensor Assembly) *28 FC Radiator Assembly
*29 EV Radiator Assembly *30 Water Temperature Sensor (for Radiator Outlet Side)
*31 FC Cooling Water Pump Assembly *32 Water Temperature Sensor (for FC Stack Outlet Side)
*33 FC Cooling Water Temperature Control Valve *34 FC Cooling Water Ion Exchanger Assembly
*35 Manual Valve *36 Air Cleaner Filter Element Sub-assembly
*37 Pressure Relief Valve *38 Pressure Relief Device
*39 FC Air Pressure Regulator Assembly (Air Sealing Valve) *40 FC Air Pressure Regulator Assembly (Air Pressure Regulating Valve)
*41 FC Air By-pass Valve Assembly (Air Shunt Valve) *42 Atmospheric Pressure Sensor (EV control ECU)
*43 Inverter with Converter Assembly *44 FC Converter Assembly
*45 EV Cooling Water Pump Assembly *46 Heater Accessory Assembly
*47 Water Pump Assembly with Motor *48 Electric Heater Sub-assembly
*49 Heater Radiator Unit Sub-assembly - -
*a Hydrogen System *b Air System
*c FC Cooling System *d EV Cooling System
*e To the Exhaust Drainage Pipe - -


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1DEF00 FC System No Activation If any of the following conditions are met:
·

Lowest cell voltage has decreased below lower voltage limit.

(1 trip detection logic)

·

Lowest cell voltage has decreased below voltage tolerance value 3 times.

(1 trip detection logic)

·

If all of the following conditions are met, and lowest cell voltage has decreased below a calculated threshold:

(1 trip detection logic)

-

Cell monitor is normal

-

+B voltage is not low

-

"FC Work Mode" is in a condition other than FC Shutdown


·

If the decreased amount of hydrogen pressure is large when the FC system stops, a cross leakage malfunction is detected.

(3 trip detection logic)

·

When the FC system start sequence has timed out, a malfunction is detected.

(1 trip detection logic)


·

FC stack assembly

·

Air system components

·

Hydrogen system components (fuel injector, hydrogen supply regulator assembly, high-range hydrogen pressure pipe, medium-range hydrogen pressure pipe, low-range hydrogen pressure pipe, exhaust drainage valve (hydrogen recirculation separator assembly), hydrogen secondary pressure sensor)

·

FC cooling system components (water temperature sensor (for FC stack outlet side), FC cooling water pump assembly)

·

FC stack coolant


Master Warning: Comes on EV B

Detection timing
Vehicle Condition FC shutdown
(ignition switch ON)
FC startup process FC intermittent operation FC is generating power
(vehicle is in stationary)
FC is generating power
(vehicle is traveling)
FC shutdown process
Data List
"FC Work Mode"
Stop Startup Working Finishing
Data List
"FC Intermittent Operation"
OFF ON OFF OFF
DTC Detection - ○ ○ ○ ○ ○

NOTICE:

If low quality hydrogen is applied, this DTC may be output.


HINT:

By accessing the "FC Work Mode" and "FC Intermittent Operation" in the freeze frame data, the FC system condition at the time the malfunction occurred can be checked.


Related Data List
DTC No. Data List
P1DEF00
·

FC Work Mode

·

FC Stack Cell Average Minimum Voltage

·

FC Stack Cell Minimum Voltage

·

Estimate FC Stack Cell Minimum Voltage 1

·

Estimate FC Stack Cell Minimum Voltage 2

·

FC Stack Cell Average Minimum Voltage ch

·

FC Stack Cell Minimum Voltage ch

·

Target Hydrogen Pump Speed

·

FC Coolant Pump Speed

·

Low-Range Hydrogen Pressure (Filtered Value)

·

Target Low-Range Hydrogen Pressure

·

Atmospheric Pressure (Filtered Value)

·

Exhaust Drainage Valve

·

Target Air Sealing Valve Position



HINT:
·

Refer to the "FC Stack Cell Minimum Voltage" and "FC Stack Cell Average Minimum Voltage" in the Data List when troubleshooting. The cell voltage is normally within approximately 0 to 1 V, and the FC voltage is in a range of approximately between from 222 to 330 V (when the vehicle is stationary and is in modes other than intermittent operation).

·

This DTC may be output due to malfunctions in the hydrogen, air or cooling systems. If DTCs for those systems are found, troubleshoot them first. In addition, check the freeze frame data and Data List values for the hydrogen pressure, air pressure, airflow volume, and FC stack outlet coolant temperature (less than approximately 75°C (167°F)).

-

Low-range hydrogen pressure:

Compare the "Target Low-range Hydrogen Pressure" and the "Low-Range Hydrogen Pressure (Filtered Value)" in the Data List.

-

Medium-range hydrogen pressure:

"Medium-Range Hydrogen Pressure (Filtered Value)" is in a range of approximately 1000 to 1600 kPa(abs).

-

Hydrogen Pump Speed:

Compare the "Target Hydrogen Pump Speed" and the "Hydrogen Pump Speed" in the Data List.

-

Air pressure:

Compare the "Target FC Inlet Air Pressure" and the "FC Inlet Air Pressure (Filtered Value)" in the Data List.

-

Airflow volume:

Compare the "Target Mass Air Flow" and the "Mass Air Flow (Filtered Value)" in the Data List.

-

FC Air Compressor Motor Speed:

Compare the "Target FC Air Compressor Motor Speed" and the "FC Air Compressor Motor Speed" in the Data List.




CAUTION / NOTICE / HINT

CAUTION:
A341072

·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

Click hereEngine / Hybrid System>FUEL>FUEL SYSTEM>PRECAUTION



NOTICE:
·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



HINT:
·

Forcing the SOC of the EV supply battery assembly to decrease by applying electrical loads such as turning on the air conditioning (HOT MAX, maximum airflow), or depressing the accelerator pedal with the shift state in park (P), the "FC Intermittent Operation" of the Data List is easily to enter OFF (power generation mode).


After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 10 to 20 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local laws.




PROCEDURE

1.CHECK DTC OUTPUT
NOTICE:

The freeze frame data*1 is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.


Pre-procedure1

a.

None


Procedure1

a.

According to the display on the GTS, check for DTCs in the Health Check.

Result:
Result Proceed to
Only P1DEF00 is output A
P1DEF00 is output and DTCs other than the DTCs in the table below are output B
P1DEF00 is output and any DTCs in the table below are output C

Malfunction Content Relevant DTC
Microcomputer malfunction/Power source circuit malfunction P1D8396 (EV) Hydrogen Pump Inverter Component Internal Failure
P1DC896 (EV) FC Coolant Pump Inverter Component Internal Failure
P1DCF96 (EV) Cell Monitor Component Internal Failure
P1EF394 (EV) Fuel Cell Control Module Unexpected Operation
Communication system malfunction P1D8387 (EV) Lost Communication with Hydrogen Pump Inverter Missing Message
P1DC887 (EV) Lost Communication with FC Coolant Pump Inverter Missing Message
P1E7F87 (EV) Communication Error from Fuel Cell Control Module to Hybrid/EV Powertrain Control Module Missing Message
Sensor and actuator circuit malfunction P010031 (EV) Mass or Volume Air Flow Sensor "A" No Signal
P1D2496 (EV) Hydrogen Pump Component Internal Failure
P1D2511 (EV) Radiator Outlet Coolant Temperature Sensor Circuit Short to Ground
P1D2515 (EV) Radiator Outlet Coolant Temperature Sensor Circuit Short to Battery or Open
P1D251C (EV) Radiator Outlet Coolant Temperature Sensor Circuit Voltage Out of Range
P1D2A11 (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Short to Ground
P1D2A15 (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Short to Battery or Open
P1D2A1C (EV) FC Stack Outlet Coolant Temperature Sensor Circuit Voltage Out of Range
P1D2F96 (EV) FC Coolant Pump Component Internal Failure
P1D7F96 (EV) FC Air Compressor Motor Component Internal Failure
P1D9011 (EV) FC Stack Inlet Pressure Sensor Circuit Short to Ground
P1D9015 (EV) FC Stack Inlet Pressure Sensor Circuit Short to Battery or Open
P1E4862 (EV) FC Stack Inlet Pressure Sensor/Barometric Pressure Sensor "B" Signal Compare Failure
P1F089F (EV) FC Shutdown Signal Stuck Off
P1F6C71 (EV) Air Sealing Valve Actuator Stuck
P1F6D71 (EV) Air Shunt Valve Actuator Stuck
P1F6E71 (EV) Air Pressure Regulating Valve Actuator Stuck
P222A12 (EV) Barometric Pressure Sensor "B" Circuit Short to Battery
P222A14 (EV) Barometric Pressure Sensor "B" Circuit Short to Ground or Open
P1D9A1C (FC) Hydrogen Injector 1 Circuit Voltage Out of Range
P1DA01C (FC) Hydrogen Injector 2 Circuit Voltage Out of Range
P1DA51C (FC) Hydrogen Injector 3 Circuit Voltage Out of Range
P1DAA12 (FC) Exhaust Drainage Valve Circuit Short to Battery
P1DAA14 (FC) Exhaust Drainage Valve Circuit Short to Ground or Open
P1DB511 (FC) Medium-Range Hydrogen Pressure Sensor Circuit Short to Ground
P1DB515 (FC) Medium-Range Hydrogen Pressure Sensor Circuit Short to Battery or Open
P1DBA11 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Ground
P1DBA15 (FC) Low-Range Hydrogen Pressure Sensor Circuit Short to Battery or Open
P1DC618 (FC) Air Sealing Valve Circuit Current Below Threshold
P1DC619 (FC) Air Sealing Valve Circuit Current Above Threshold
P1DC711 (FC) Air Sealing Valve Position Sensor Circuit Short to Ground
P1DC715 (FC) Air Sealing Valve Position Sensor Circuit Short to Battery or Open
P1DD514 (FC) Radiator Rotary Valve Circuit 1 Circuit Short to Ground or Open
P1E7A18 (FC) Air Shunt Valve Circuit Current Below Threshold
P1E7A19 (FC) Air Shunt Valve Circuit Current Above Threshold
P1E7B11 (FC) Air Shunt Valve Position Sensor Circuit Short to Ground
P1E7B15 (FC) Air Shunt Valve Position Sensor Circuit Short to Battery or Open
P1E7C18 (FC) Air Pressure Regulating Valve Circuit Current Below Threshold
P1E7C19 (FC) Air Pressure Regulating Valve Circuit Current Above Threshold
P1E7D11 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Ground
P1E7D15 (FC) Air Pressure Regulating Valve Position Sensor Circuit Short to Battery or Open
P1E7E87 (FC) Lost Communication with Hybrid/EV Powertrain Control Module (SIL) Missing Message
P1EFD14 (FC) Radiator Rotary Valve Circuit 2 Circuit Short to Ground or Open
P1EFE14 (FC) Radiator Rotary Valve Circuit 3 Circuit Short to Ground or Open
P1EFF14 (FC) Radiator Rotary Valve Circuit 4 Circuit Short to Ground or Open
System malfunction P1D2F00 (EV) FC Coolant Pump Performance
P1D3F16 (EV) FC Stack Internal Voltage Circuit Voltage Below Threshold
P1D7F62 (EV) FC Air Compressor Motor Signal Compare Failure
P1DC000 (EV) Low-Range Hydrogen Pressure Too Low
P1DC500 (EV) FC Air Pressure Too High
P1DDF00 (EV) FC Air Flow Malfunction
P1DDF79 (EV) FC Air Flow Mechanical Linkage Failure
P1DE400 (EV) FC Cooling System Performance


HINT:
·

DTC P1DEF00 may be store due to problems that cause the DTCs shown above to be output. If such happens, troubleshoot the suspected area(s) corresponding to the output DTC(s) in order of the listed DTCs shown in the table above.

·

*1: The "FC Stack Cell Minimum Voltage" or "FC Stack Cell Average Minimum Voltage" may have been below approximately 0 V. While the FC stack is warmed up in quick mode when the FC system is cold, the cell voltage may decrease even if the FC system is normal.




Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK COOLANT (FC STACK COOLANT) LEAK

B

2.CHECK COOLANT (FC STACK COOLANT) LEAK

C

GO TO DTC CHART

2.CHECK COOLANT (FC STACK COOLANT) LEAK

Pre-procedure1

a.

None


Procedure1

a.

Check the FC stack coolant level in the FC radiator reserve tank.


b.

Check for FC coolant leaks.

Click hereEngine / Hybrid System>COOLING>COOLING SYSTEM>ON-VEHICLE INSPECTION

Result:
Result Proceed to
No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line. A
No leaks are found and the FC coolant level in the FC radiator reserve tank is below the low line. B
FC coolant leaks are evident. C


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.




Post-procedure1

a.

None



A

3.CHECK COOLANT HOSE

B

38.ADD FC STACK COOLANT

C

INSPECT COOLANT LEAK AND ADD COOLANT

3.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged



Result:
Proceed to
OK
NG



OK

4.CHECK FC STARTUP

NG

REPAIR OR REPLACE COOLANT HOSE

4.CHECK FC STARTUP

Pre-procedure1

a.

Turn the ignition switch ON.


Procedure1

a.

Turn the ignition switch to ON (READY) while checking the "FC Work Mode" and "Target Air Sealing Valve Position".

Powertrain > EV > Data List
Tester Display
FC Work Mode
Target Air Sealing Valve Position
50003 397 962,737
Result:
Result Proceed to
"FC Work Mode" switches to "Working" A
The "FC Work Mode" is "Stop" without switching to "Working", and the "FC Work Mode" switches to "Stop" after the "Target Air Sealing Valve Position" reaches 100% with the "FC Work Mode" being "Startup" B
The "FC Work Mode" is "Stop" without switching to "Working", and the "FC Work Mode" switches to "Stop" with the "Target Air Sealing Valve Position" remaining at 0% and the "FC Work Mode" being "Startup" C



Post-procedure1

a.

Turn the ignition switch off.



A

5.CHECK FREEZE FRAME DATA

B

26.CHECK FREEZE FRAME DATA

C

36.PERFORM LEAK CHECK
5.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None


Procedure1

a.

Read the freeze frame data of DTC P1DEF00.

Powertrain > EV > DTC(P1DEF00) > Freeze Frame Data
Tester Display
Atmospheric Pressure (Filtered Value)
FC Work Mode
Estimate FC Stack Cell Minimum Voltage 1
Estimate FC Stack Cell Minimum Voltage 2
Target Low-Range Hydrogen Pressure
Low-Range Hydrogen Pressure (Filtered Value)
50040 397 889,962,926,927,1033,1032 P1DEF00
Result:
Result Proceed to
"Low-Range Hydrogen Pressure (Filtered Value)" is lower than "Target Low-Range Hydrogen Pressure" by 15 kPa or more A
The "FC Work Mode" is "Startup" and the difference between the "Low-Range Hydrogen Pressure (Filtered Value)" and "Atmospheric Pressure (Filtered Value)" is +/-5 kPa or more
"FC Work Mode" is Finishing, and "Estimate FC Stack Cell Minimum Voltage 1" and "Estimate FC Stack Cell Minimum Voltage 2" are -0.3 V or higher B
Other than above C



Post-procedure1

a.

Turn the ignition switch off.



A

6.CHECK HYDROGEN GAS LEAK

B

REPLACE FC STACK ASSEMBLY

C

11.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
6.CHECK HYDROGEN GAS LEAK
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.

·

Open the hood with the ignition switch off, check for hydrogen leaks around the underbody and in the front compartment with a hydrogen gas detector. If leakage is found, pay extra attention to fire safety in the following operations.



HINT:

For procedures to check for leaks from hydrogen pipes and components (high-range pressure and medium-range pressure), refer toEngine / Hybrid System>FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION.


Pre-procedure1

a.

Turn the ignition switch off.


b.

Remove the under cover.


Procedure1

a.

Check that the hydrogen tank and hydrogen pipes are not damaged.


b.

Check for a gas leaking sound, and then check if there are hydrogen leaks in the hydrogen pipes and components with a hydrogen gas detector.

A477015C02
6.219,3.813 6.031,3.052 true 6.469,3.281 6.469,2.99 true 4.01,2.719 4.219,2.635 true 4.688,1.406 5.104,0.698 true 5.646,3.49 5.729,2.813 true 6.635,1.833 6.729,1.135 true 4.969,2.323 5.563,2.177 true 4.917,2.146 5.26,2.042 true 4.969,2.469 5.323,2.396 true 2.552,2.135 2.844,1.667 true 4.906,2.031 5.479,1.729 true 2.698,3.563 3.188,2.792 true 1.292,2.104 1.979,1.5 true 0.531,1.885 0.24,0.927 true 4.49,3.708 4.396,3.313 true 6.406,2.865 6.146,2.25 true 4.208,2.177 4.01,1.781 true 4.906,3.885 4.854,3.26 true 5.021,3.052 5.469,3.979 true 0.99,1.854 1.313,1.115 true 6.24,4.01 6.448,4.198 0.208,0.188 10 false *1 5.563,3.563 5.802,3.729 0.24,0.167 10 false *2 5.281,1.969 5.594,2.125 0.313,0.156 10 false *3 5.51,1.635 5.823,1.792 0.313,0.156 10 false *5 2.865,1.51 3.177,1.667 0.313,0.156 10 false *6 1.302,0.979 1.615,1.135 0.313,0.156 10 false *14 6.667,0.958 6.979,1.115 0.313,0.156 10 false *8 6.042,2.063 6.354,2.219 0.313,0.156 10 false *9 5.427,4.021 5.896,4.177 0.469,0.156 10 false *10 2.583,3.583 3.052,3.74 0.469,0.156 10 false *11 2.01,1.375 2.281,1.531 0.271,0.156 10 false *12 0.708,3.26 1.021,3.417 0.313,0.156 10 false : *a 0.719,3.49 1.031,3.646 0.313,0.156 10 false : *b 0.729,3.75 1.042,3.906 0.313,0.156 10 false : *c 0.75,4.01 1.063,4.167 0.313,0.156 10 false : *d 3.823,2.698 4.063,2.865 0.24,0.167 10 false *2 5.375,2.323 5.688,2.479 0.313,0.156 10 false *3 5.177,0.604 5.49,0.76 0.313,0.156 10 false *7 4.781,2.99 5.25,3.146 0.469,0.156 10 false *10 6.406,3.323 6.646,3.49 0.24,0.167 10 false *2 4.385,3.781 4.625,3.948 0.24,0.167 10 false *2 5.615,2.094 5.927,2.25 0.313,0.156 10 false *4 3.885,1.542 4.198,1.698 0.313,0.156 10 false *9 4.844,3.938 5.156,4.094 0.313,0.156 10 false *9 0.115,0.76 0.385,0.917 0.271,0.156 10 false *13
*1 Hydrogen Inlet Receptacle Assembly *2 High-range Hydrogen Pressure Pipe (for filling)
*3 Hydrogen Tank Tube Joint *4 Hydrogen Tank Pressure Sensor (for Inlet Side)
*5 Hydrogen Tank Pressure Sensor (for Outlet Side) *6 No. 1 Hydrogen Tank Assembly
*7 No. 2 Hydrogen Tank Assembly *8 No. 3 Hydrogen Tank Assembly
*9 High-range Hydrogen Pressure Pipe (for feeding) *10 Hydrogen Supply Regulator Assembly
*11 Medium-range Hydrogen Pressure Pipe *12 Low-range Hydrogen Pressure Pipe
*13 FC Stack Assembly *14 Hydrogen Injector
*a High-range Pressure Area (when filling)
(Hydrogen Inlet Receptacle Assembly → Hydrogen Tank Assembly )
*b High-range Pressure Area
(Hydrogen Tank Assembly → Hydrogen Supply Regulator Assembly)
*c Medium-range Pressure Area
(Hydrogen Supply Regulator Assembly → Hydrogen Injector)
*d Low-range Pressure Area
(Hydrogen Injector → FC Stack)



Standard value:

300 ppm or less. (Hydrogen gas detector)


Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the under cover.



OK

7.READ VALUE USING GTS (HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

NG

35.CHECK HYDROGEN GAS LEAKAGE POINT
7.READ VALUE USING GTS (HIGH-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
High-Range Hydrogen Pressure (Filtered Value)
50003 397 1030
Result:
Result Proceed to
The value of High-Range Hydrogen Pressure (Filtered Value) is less than 5000 kPa(abs) A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

8.CHARGE HYDROGEN GAS

B

9.READ VALUE USING GTS (MEDIUM-RANGE HYDROGEN PRESSURE (FILTERED VALUE))
8.CHARGE HYDROGEN GAS
a.

Fill the tank until the "High-Range Hydrogen Pressure (Filtered Value)" in the Data List exceeds 5000 kPa(abs).


Result:
Proceed to
NEXT



NEXT

9.READ VALUE USING GTS (MEDIUM-RANGE HYDROGEN PRESSURE (FILTERED VALUE))
9.READ VALUE USING GTS (MEDIUM-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Medium-Range Hydrogen Pressure (Filtered Value)
50003 397 1031
Result:
Result Proceed to
The value of Medium-Range Hydrogen Pressure (Filtered Value) is 1100 kPa(abs) or less A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN SUPPLY REGULATOR ASSEMBLY

B

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT HYDROGEN INJECTOR)
10.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT HYDROGEN INJECTOR)

Pre-procedure1

a.

None


Procedure1

a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working and "FC Intermittent Operation" is OFF.

Powertrain > EV > Active Test
Active Test Display
Control the Select Hydrogen Injector
Data List Display
FC Work Mode
FC Intermittent Operation
Hydrogen Injector 1 Injection Period
Hydrogen Injector 2 Injection Period
Hydrogen Injector 3 Injection Period
Medium-Range Hydrogen Pressure (Filtered Value)
Low-Range Hydrogen Pressure (Filtered Value)
50004 397 42005 962,872,739,740,741,1031,1032

b.

While performing the "Control the Select Hydrogen Injector" Active Test, check "Medium-Range Hydrogen Pressure (Filtered Value)" and "Low-Range Hydrogen Pressure (Filtered Value)" in the Data List.

NOTICE:

If the Active Test cannot be performed, check "Low-Range Hydrogen Pressure (Filtered Value)" and "Medium-Range Hydrogen Pressure (Filtered Value)" when either "Hydrogen Injector 1 Injection Period", "Hydrogen Injector 2 Injection Period" or "Hydrogen Injector 3 Injection Period" in the Data List when started is a value other than 0 μs.


HINT:

If either "Hydrogen Injector 1 Injection Period", "Hydrogen Injector 2 Injection Period" or "Hydrogen Injector 3 Injection Period" shows a value other than 0 μs, an injection command is being sent to the injector.


Reference example
A476939E01
2.552,2.281 2.969,2.656 false 0.094,0.083 2.896,0.594 2.802,0.51 10 false Hydrogen Injector 1 (2) (3) Injection Request 0.604,1.448 1.219,1.646 0.615,0.198 10 false 0 μs 2.698,1.875 4.688,2.073 1.99,0.198 10 false One injection 0.271,1.927 2.219,2.521 1.948,0.594 10 false Low-Range Hydrogen Pressure (Filtered Value) 0.135,2.427 1.021,2.771 0.885,0.344 10 false 165 kPa(abs) 0.135,3.26 1.021,3.604 0.885,0.344 10 false 140 kPa(abs) 3.146,2.354 4.031,2.698 0.885,0.344 10 false 160 kPa(abs) 3.156,3.188 4.042,3.531 0.885,0.344 10 false 145 kPa(abs) 1.667,2.177 2.635,2.635 0.969,0.458 10 false 5 kPa or more

Result:
Result Proceed to
For each hydrogen injector, their "Low-Range Hydrogen Pressure (Filtered Value)s" in the Data List increase by more than 5 kPa per injection.
(During normal operation)
A
"Medium-Range Hydrogen Pressure (Filtered Value)" in the Data List decreases 100 kPa or more per injection for each hydrogen injector*1 B
"Low-Range Hydrogen Pressure (Filtered Value)" in the Data List changes significantly over the target value during 1 injection by each of the hydrogen injectors*2 C
Pressure does not change when each of the hydrogen injectors is performing injection, or any of the hydrogen injectors is not performing injection*3 D


HINT:
·

*1: The decrease in "Medium-Range Hydrogen Pressure (Filtered Value)" may be due to insufficient supply caused by a malfunction in the hydrogen supply regulator assembly.

·

*2: When there is a blockage in the low pressure hydrogen pipes, "Low-Range Hydrogen Pressure (Filtered Value)" increases significantly when the hydrogen injector is performing injection, and decreases rapidly when the hydrogen injector stops injection.

·

*3: The hydrogen injector is malfunctioning.

·

*3: As to the change in pressure caused by the hydrogen injector's injection, be sure to check it in all of the hydrogen injectors.

·

*3: If all hydrogen injectors are malfunctioning, replace the hydrogen supply pressure regulator assembly.




Post-procedure1

a.

None



A

11.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

B

REPLACE HYDROGEN SUPPLY REGULATOR ASSEMBLY

C

27.CHECK HYDROGEN LOW-PRESSURE PIPING

D

REPLACE MALFUNCTIONING FUEL INJECTOR ASSEMBLY
HINT:

If all hydrogen injectors are malfunctioning, replace the hydrogen supply pressure regulator assembly



11.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Check that the air cleaner filter element sub-assembly is not clogged.

OK:

The air cleaner filter element sub-assembly is not clogged



Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE AND EXHAUST PIPING

NG

12.CLEAN OR REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
12.CLEAN OR REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Clean or replace the air cleaner filter element sub-assembly.

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CLEANER FILTER ELEMENT>REMOVAL



Result:
Proceed to
NEXT



NEXT

13.CHECK INTAKE AND EXHAUST PIPING
13.CHECK INTAKE AND EXHAUST PIPING
a.

Check that no air comes in without flowing through each part of the intake air system and the exhaust drainage pipe is not clogged, disconnected, or damaged.

OK:

The intake and exhaust piping is not clogged, disconnected or damaged



Result:
Proceed to
OK
NG



OK

14.CHECK EXHAUST HYDROGEN GAS

NG

20.REPAIR OR REPLACE MALFUNCTIONING PARTS
14.CHECK EXHAUST HYDROGEN GAS
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



Pre-procedure1

a.

Ensure the safety of the areas in front and at the back of the vehicle.


b.

Put wheel chocks and securely apply the parking brake.


Procedure1

a.

Turn the ignition switch to ON (READY) with the shift state in park (P), and check that the Data List "FC Work Mode" is Working, "FC Intermittent Operation" is OFF, and "Exhaust Drainage Valve" is Close.

Powertrain > EV > Active Test
Active Test Display
Activate the Exhaust Drainage Valve
Data List Display
FC Work Mode
FC Intermittent Operation
Exhaust Drainage Valve
50004 397 42006 962,872,818

b.
A476956C02
0.875,2.563 1.833,1.885 true 2.042,2.042 2.75,1.583 2.75,1.583 2.938,1.573 true 0.604,2.563 0.917,2.76 0.313,0.198 10 true *1 3,1.49 3.313,1.688 0.313,0.198 10 true *2
*1 Tailpipe
*2 Hydrogen Gas Detector Probe


Use the hydrogen gas detector to measure and record the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is closed.

NOTICE:
·

Perform this measurement in an environment where there is no wind.

·

Position the hydrogen gas detector probe in an area 100 mm (3.94 in.) away from the tailpipe opening. (Avoid locations underneath the tailpipe opening)

·

Position the hydrogen gas detector probe so that it is free from dropping water that comes from the tailpipe opening.




c.

Perform the "Activate the Exhaust Drainage Valve" Active Test several times over 1 minute, and then, starting from the third test, use the hydrogen gas detector to measure the hydrogen concentration in gas released from the tailpipe when the exhaust drainage valve is open.

HINT:
·

The exhaust drainage valve will open for 1 second each time the Active Test is performed, so measure the hydrogen concentration for several seconds.

·

Hydrogen concentration may not increase while coolant escapes when the valve is first opened. Therefore, start measuring from the third test.

·

There is a delayed response when performing detection using the hydrogen gas detector, so measure for several seconds.

·

"FC Intermittent Operation" in the Data List will be more likely to turn OFF if the accelerator pedal is depressed with the shift state in park (P).




Result:
Result Proceed to
The hydrogen concentration of the hydrogen gas detector will increase when "Exhaust Drainage Valve" in the Data List is Open rather than when "Exhaust Drainage Valve" is Close. A
Other than above* B


*: The exhaust drainage valve is malfunctioning

Exhaust drainage valve is stuck closed:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained low.


Exhaust drainage valve is stuck open:

Regardless of the "Exhaust Drainage Valve Driving Request" being ON or OFF, the concentration shown on the hydrogen gas detector has remained high when the ignition switch is on (READY).



Post-procedure1

a.

Turn the ignition switch off.



A

15.CHECK VEHICLE CONTROL HISTORY

B

REPLACE HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

15.CHECK VEHICLE CONTROL HISTORY
a.

Check Vehicle Control History (RoB).

Powertrain > EV > Utility
Tester Display
Vehicle Control History (RoB)
50005 397 55
Result:
Result Proceed to
Vehicle control history item "FC System Start/Stop Failure" is not output A
Vehicle control history item "FC System Start/Stop Failure" is output B




A

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)

B

26.CHECK FREEZE FRAME DATA
16.PERFORM ACTIVE TEST USING GTS (CONTROL THE FC COOLANT PUMP)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

Check that "FC Stack Outlet Coolant Temperature (Filtered Value)" is 40°C or more.

Powertrain > EV > Active Test
Active Test Display
Control the FC Coolant Pump
Data List Display
FC Coolant Pump Drive Speed
FC Coolant Pump Speed
Target FC Coolant Pump Speed
FC Stack Outlet Coolant Temperature (Filtered Value)
50004 397 17 704,909,908,998
HINT:

If 40°C or less, drive the vehicle on urban roads for approximately 10 minutes to warm it up.



b.

Perform the Active Test for 10 seconds or more at 3100 rpm.


Result:
Proceed to
NEXT


Post-procedure1

a.

None



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1D2F00 is output A
DTCs are not output B


HINT:

P1DEF00 (FC System No Activation) may be output due to the FC cooling water pump assembly, so check if P1D2F00 (FC Coolant Pump Performance) is output.



Post-procedure1

a.

Turn the ignition switch off.



B

18.INSPECT WATER TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

A

REPLACE FC COOLING WATER PUMP ASSEMBLY

18.INSPECT WATER TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

OK

19.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

NG

REPLACE WATER TEMPERATURE SENSOR (FOR FC STACK OUTLET SIDE)

19.READ VALUE USING GTS (LOW-RANGE HYDROGEN PRESSURE (FILTERED VALUE))

Pre-procedure1

a.

Remove the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor).

HINT:

Click hereEngine / Hybrid System>FC CONTROL>HYDROGEN PRESSURE SENSOR>REMOVAL



b.

Reconnect the hydrogen secondary pressure sensor (low-range hydrogen pressure sensor) connector.


Procedure1

a.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Low-Range Hydrogen Pressure (Filtered Value)
50003 397 1032

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa (15 psi).

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (0.1 psi). This varies by weather.




c.

Compare the "Low-Range Hydrogen Pressure (Filtered Value)" values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Difference between "Low-Range Hydrogen Pressure (Filtered Value)" in Data List and normal atmospheric pressure value is 35 kPa or more. A
Other than above. B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE HYDROGEN SECONDARY PRESSURE SENSOR

B

21.CLEAR DTC
20.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

14.CHECK EXHAUST HYDROGEN GAS
21.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

22.SIMULATION TEST
22.SIMULATION TEST

Pre-procedure1

a.

Drive the vehicle for 10 to 20 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).

If vehicle speeds, accelerator pedal positions, road conditions, ambient temperatures and climates at the time the malfunction occurred can be confirmed, take them into account.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1DEF00 is output B


NOTICE:

If low quality compressed hydrogen is applied, this DTC may be output.



Post-procedure1

a.

Turn the ignition switch off.



A

B

23.REPLACE FC STACK ASSEMBLY
23.REPLACE FC STACK ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.CLEAR DTC
24.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

25.SIMULATION TEST
25.SIMULATION TEST

Pre-procedure1

a.

Drive the vehicle for 10 to 20 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).

If vehicle speeds, accelerator pedal positions, road conditions, ambient temperatures and climates at the time the malfunction occurred can be confirmed, take them into account.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1DEF00 is output B


NOTICE:

If low quality compressed hydrogen is applied, this DTC may be output.



Post-procedure1

a.

Turn the ignition switch off.



A

END

B

REPLACE HYDROGEN RECIRCULATION PUMP ASSEMBLY

26.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None


Procedure1

a.

Read the freeze frame data of Vehicle control history item "FC System Start/Stop Failure".

Confirmation Item
Target Hydrogen Pump Speed
FC Coolant Pump Speed

Result:
Result Proceed to
"Target Hydrogen Pump Speed" is 3900 to 4100 rpm and "FC Coolant Pump Speed" is 3800 rpm or less A
Other than above B



Post-procedure1

a.

Clear the Vehicle Control History (RoB).

HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>VEHICLE CONTROL HISTORY (RoB)




A

B

29.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))
27.CHECK HYDROGEN LOW-PRESSURE PIPING
a.

Check the hydrogen low-pressure piping for deformation or damage.

OK:

The hydrogen low-pressure piping is not deformed or damaged



Result:
Proceed to
OK
NG



OK

28.CHECK HYDROGEN LOW-PRESSURE PIPING

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

28.CHECK HYDROGEN LOW-PRESSURE PIPING
a.

Remove the hydrogen low-pressure piping and check for blockage in the filter, etc. as well as internal deformation or damage.

OK:

There is no blockage in filter, etc., and no internal deformation or damage



Result:
Proceed to
OK
NG



OK

REPLACE FC STACK ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

29.READ VALUE USING GTS (MASS AIR FLOW (FILTERED VALUE))

Pre-procedure1

a.

None


Procedure1

a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > EV > Data List
Tester Display
Mass Air Flow (Filtered Value)
50003 397 897
Result:
Result Proceed to
The value of Mass Air Flow (Filtered Value) is less than 8 L/min A
None of the above conditions are met B



Post-procedure1

a.

Turn the ignition switch off.



A

30.CLEAR DTC

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

30.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

31.SIMULATION TEST
31.SIMULATION TEST

Pre-procedure1

a.

Drive the vehicle for 10 to 20 minutes according to the freeze frame data (Vehicle Speed, Accelerator Degree, etc.).

If vehicle speeds, accelerator pedal positions, road conditions, ambient temperatures and climates at the time the malfunction occurred can be confirmed, take them into account.

CAUTION:

Perform this road test only in an appropriate safe location, in accordance with all local traffic laws.



Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
P1DEF00 is output B


NOTICE:

If low quality compressed hydrogen is applied, this DTC may be output.



Post-procedure1

a.

Turn the ignition switch off.



A

B

32.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)
32.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air sealing valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air sealing valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air sealing valve).



OK

33.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR SEALING VALVE)

33.CHECK FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

Pre-procedure1

a.

Remove the FC air pressure regulator assembly (air pressure regulating valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR CONTROL VALVE>REMOVAL



Procedure1

a.

Visually check the FC air pressure regulator assembly (air pressure regulating valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air pressure regulator assembly (air pressure regulating valve).



OK

34.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

NG

REPLACE FC AIR PRESSURE REGULATOR ASSEMBLY (AIR PRESSURE REGULATING VALVE)

34.CHECK FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

Pre-procedure1

a.

Remove the FC air by-pass valve assembly (air shunt valve).

HINT:

Click hereEngine / Hybrid System>INTAKE / EXHAUST>AIR BYPASS VALVE>REMOVAL



Procedure1

a.

Visually check the FC air by-pass valve assembly (air shunt valve).

OK:

The valve shaft is not bent or otherwise damaged



Result:
Proceed to
OK
NG


Post-procedure1

a.

Install the FC air by-pass valve assembly (air shunt valve).



OK

REPLACE FC STACK ASSEMBLY

NG

REPLACE FC AIR BY-PASS VALVE ASSEMBLY (AIR SHUNT VALVE)

35.CHECK HYDROGEN GAS LEAKAGE POINT
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



a.

Apply soapy water to locate hydrogen leaking areas.

NOTICE:

Do not apply soapy water to the FC stack assembly. If a hydrogen gas detector identifies gas leaks from the FC stack assembly, replace the FC stack assembly with new one.


Result:
Proceed to
NEXT




NEXT

REPLACE MALFUNCTIONING PARTS

36.PERFORM LEAK CHECK
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



a.

Perform Leak Check (Low Pressure Point Leak Check) in the Utility menu.

Powertrain > EV > Utility
Tester Display
Leak Check
50005 397 4671

b.

While performing the Low Pressure Point Leak Check, check the "Low-Range Hydrogen Pressure (Filtered Value)" and "Target Low-Range Hydrogen Pressure" displayed on the GTS.


c.

While performing the Low Pressure Point Leak Check, measure the hydrogen concentration around the FC stack and at the tailpipe with a hydrogen gas detector.


Result:
Result Proceed to
The hydrogen concentration around the FC stack is 300 ppm or more A
The "Low-Range Hydrogen Pressure (Filtered Value)" displayed on the GTS is below the "Target Low-Range Hydrogen Pressure" B
The hydrogen concentration at the tailpipe is 30000 ppm or more (If the measurement range of the hydrogen gas detector is insufficient, the hydrogen concentration reaches 90% of the upper limit of the measurement range within 5 seconds of starting a measurement) C
The hydrogen concentration at the tailpipe is below 30000 ppm (If the measurement range of the hydrogen gas detector is insufficient, the hydrogen concentration does not reach 90% of the upper limit of the measurement range within 5 seconds of starting a measurement) D



A

37.CHECK HYDROGEN GAS LEAKAGE POINT

B

REPLACE HYDROGEN SUPPLY REGULATOR ASSEMBLY

C

REPLACE HYDROGEN RECIRCULATION SEPARATOR ASSEMBLY

D

REPLACE FC STACK ASSEMBLY

37.CHECK HYDROGEN GAS LEAKAGE POINT
CAUTION:
·

Work procedures must be performed in an area with good ventilation (airflow) where hydrogen gas will not accumulate, and flames or other things that could act as ignition sources must not be present.

·

Accumulated hydrogen gas could ignite, resulting in a serious accident.



a.

Perform Leak Check (Low Pressure Point Leak Check) in the Utility menu.

Powertrain > EV > Utility
Tester Display
Leak Check
50005 397 4671

b.

Apply soapy water to locate hydrogen leaking areas.

NOTICE:

Do not apply soapy water to the FC stack assembly. If a hydrogen gas detector identifies gas leaks from the FC stack assembly, replace the FC stack assembly with new one.


Result:
Proceed to
NEXT




NEXT

REPLACE MALFUNCTIONING PARTS

38.ADD FC STACK COOLANT

Pre-procedure1

a.

Add FC stack coolant and bleed air.


Procedure1

a.

After bleeding air, check the coolant level and check for coolant leaks again.

OK:

No leaks are found and the FC coolant level in the FC radiator reserve tank is above the low line.


HINT:
·

After repairing the FC coolant leaks and adding coolant, perform the "Control the FC Coolant Pump" and "Control the Radiator Fan 1" Active Test and make sure that there are no malfunctions.

·

If a coolant leak cannot be found despite that the coolant in the radiator reserve tank is below the Low level, leakage may have occurred inside the FC stack or in the air conditioning system.

In this case, add coolant and then bleed air from the coolant. If the coolant level is still too low but a coolant leak cannot be confirmed even in the air conditioning system, the coolant leak is in the FC stack. Replace the FC stack.

·

If there is a leak in the FC stack, DTC P0AA649 may be output to the EV control ECU.



Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

END

NG

REPLACE FC STACK ASSEMBLY